用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

一种适合∑-△A／D转换器的FIR数字滤波器

讨论了一种用于∑-△A／D转换器的固定系数半带（half-band）FIR数字滤波器，分析了其线性相位特性和低通滤波特性，给出了频率仿真结果，以及在Cadence设计系统中的电路和版图实现。     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

一种平面结构的V波段上变频器

介绍了平面结构的V波段变频器，该变频器采用平衡变频结构，变频电路主体为平面结构，同时采用了E面探针结构的波导微带转换作为射频信号输出，文中给出了该上变频器的电路软件仿真结果和实测结果以及E面探针波导微带转换的仿真和测试结果，最后给出了该上变频器的实物结构。     

基于谐振原理的硅微机械加速度计

基于力学振动原理 ,导出敏感梁类谐振振动的微分方程 ,给出了振梁型加速度计的设计原理。指出了加速度计谐振梁频率的相对变化量与梁的厚度无关 ;为避免输出非线性频率信号 ,频率的相对变化率和激励振动的振幅都不宜太大