Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

A methodology for the estimation of transverse failure strength of an oxidized lamina from isothermal aging studies

Surface oxidation and ensuing damage substantially decrease the service life of High Temperature Polymer Matrix Composite (HTPMC) structures. Oxidative degradation behavior of composites is strongly dependent on the coupling between chemical and mechanical responses of the material. In a composite lamina, the onset of damage and subsequent coupled acceleration of both damage and oxidation are controlled by the transverse failure strength of the oxidized regions. The direct measurement of this strength from experimentation is challenging and cumbersome. A model-based methodology for estimating the mean transverse failure strength of the oxidized regions of a unidirectional composite is described in this paper. As the strength of the oxidized region is expected to show a high-degree of spatial variability, the estimated mean is shown to be relatively insensitive to the effect of strength variance. The developed methodology is illustrated with isothermal aging data available for a typical high-temperature composite system.     

Kinetics of light-induced degradation in compensated boron-doped silicon investigated using photoluminescence and numerical simulation

We use photoluminescence to observe light-induced degradation in silicon in real time. Numerical simulations are used to match our results and lifetime decay data from the literature with theoretical models for the generation of the light-induced boron–oxygen defects. It is found that the existing model of the slowly generated defect SRC, where its saturated concentration is a function of the majority carrier concentration, does not explain certain results in both p- and n-type samples. A new model is proposed in which the saturated SRC concentration is controlled by the total hole concentration under illumination.     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

Environmental factors and kinetics of microbial degradation of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) in an aqueous medium

Environmental factors such as oxygen, temperature, and microbial species may have significant effects on decomposition of biodegradable polymers. A representative biodegradable, thermoplastic polymer, poly(3‐hydroxybutyrate‐co‐hydroxyvalerate) (PHBV), was decomposed in an aqueous medium under controlled laboratory conditions by soil microbes for the intrinsic degradation kinetics and the effects of the environmental factors on polymer biodegradation. The amount of proteins, including the PHBV depolymerases, that attached to the polymer surfaces was quite constant during the period of significant mass loss of the polymer specimens. The microbial polymer degradation followed a zero‐order rate model, so the residual mass fraction of PHBV films declined linearly with time. The mixed aerobic microbial organisms from fertile soil showed a higher activity of polymer degradation than an aerobic PHBV‐producing bacterium and the mixed anaerobes in the same soil. The mixed anaerobic microorganisms from barren soil decomposed the polymer at a slower rate than the anaerobes from fertile soil, and this was attributed to fewer microbial cells in the barren soil instead of the difference in the microbial species. The temperature effect on PHBV degradation can be described with an Arrhenius equation, and the activation energy is around 16 kcal/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 205–213, 2003     

气流式加速度传感器的敏感机理

介绍了在研制气流式加速度传感器过程中，为对气流式加速度传感器进行建模，作者对气流式加速度传感器的工作机理进行了理论性探讨。在分析过程中以流体力学、传热学和惯性理论为基础并结合实验结果，建立了适合于气流式加速度传感器的气体运动方程和能量方程。同时还讨论了热线测量加速度的方法及根据实验分析了输入加速度对腔体内温度及传感器输出电压的影响，从而为进一步研究一系列气流式传感器的工作机理提供了方法。     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

Abrasion phenomena in twill tencel fabric

The abrasion characteristics of Tencel fabrics were evaluated by Martindale abrasion and laundering, and the breakdown mechanism of fibers was surveyed by scanning electron microscopy. The fabric was subjected to pad‐dry‐cure treatment with two different types of modified dimethyloldihydroxyethylene urea resins (Reaktant DH and Reaktant FC). Although the degree of dry abrasion varied with different resins, the damage exhibited by individual fibers differed little from untreated to resin‐treated; the major mechanism of abrasion was through friction, and the mechanism of fiber failure was multiple splitting and transverse cracking. In untreated Tencel, the characteristic feature of wet abrasion was massive fibrillation, and in crosslinked fabrics, the wet abrasion mechanism was through fiber slippage and slicing action, although in the Reaktant FC‐treated fabric, the wet abrasion mechanism was more through slicing than through fiber splitting. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1391–1398, 2006     

阳离子化多元醇防塌剂的研制

室内研究和现场应用表明,聚乙烯醇类防塌剂表现出较明显的增粘负效应,可引起钻井液粘度的急剧增加,严重影响其推广应用.通过金属盐催化降解和阳离子化反应,研制出了抑制性好且增粘负效应低的阳离子化改性多元醇防塌剂.考察了阳离子化试剂、反应温度、反应时间对取代度、反应效率和产品主要性能的影响,得出了阳离子化多元醇防塌剂最佳制备条件,即：PVA与阳离子化试剂物质的量比为1：1,反应温度为50℃,反应时间为4 h,阳离子度可达0.435.