用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。     

A new controller for boost dc–dc converters based on a novel sliding surface

ABSTRACT

In this paper, two control schemes for boost converters affected by uncertainties in input voltage and load are proposed. The boost converter dynamics is redefined in terms of new state variables to facilitate the use of a disturbance observer that can estimate matched and unmatched disturbances. A sliding surface, which is new in the context of boost converters, is proposed to enable tracking and regulation of output voltage without requiring measurement of input voltage and load current. The stability of the overall system including the disturbance observer, the sliding variable and the output is proved. The performance of the schemes is assessed for regulation of output voltage and tracking of reference voltage by simulation as well as experimentation in which various types of uncertainties and various types of reference voltages are considered.     

超精密气体静压系统节流器法向随机微振动研究

以无气腔平面节流器为研究对象,对节流器流固耦合法向随机微振动进行了理论仿真和实验研究。受限于节流器厚度与气膜厚度尺寸的差异和输入初始边界条件,建立了节流器的COMSOL仿真简化模型,对节流器-气膜微流场进行双向流固耦合数值模拟。仿真结果表明,节流器的法向随机微振动幅值关于节流器中心对称,且由中心向边缘逐渐增大;微振动幅值随气体入口流速的增大而增大。实验采用纳米级激光测振仪,依次测量供气压力为0.1,0.2,…,0.5 MPa时尺寸为75 mm×50 mm×14 mm的HEXAGON双环联结型节流器多个不同位置的法向振动,实验结果表明,法向随机微振动幅值分布特性与仿真结果一致,关于节流器中心对称,且由中心向边缘逐渐增大,验证了节流器法向微振动的"跷跷板"振动形式;在0.5 MPa供气压力下,边缘振动幅值超过1 nm。对实验数据进行功率谱密度分析,结果表明不同供气压力下法向随机微振动均在9.4 kHz和10.6 kHz处产生较大功率,可认为与节流器-气膜流固耦合系统的固有频率有关。研究结果有效地揭示了节流器法向随机微振动的特性,为气体静压系统避开随机共振区、优化气体静压系统的设计提供了理论指导。     

采动覆岩卸荷膨胀累积效应

地下煤层开采引起的岩层运动是一系列安全和环境问题的根源,研究采动岩层运动规律是安全、高效、绿色开采的重要基础。通过对岩层运动过程的研究,揭示了采动覆岩卸荷膨胀累积效应及其对岩层运动规律的影响机制。研究表明:采动覆岩经历了卸荷膨胀与再压实的动态过程。受关键层结构控制,上覆岩层由下向上成组破断运动,关键层破断前,阻断了上覆载荷向下方岩层的传递,导致其因卸荷而产生膨胀,包括碎胀与弹性膨胀。随着关键层破断高度增加,覆岩卸荷高度同步增大,因卸荷而膨胀的岩层总厚度不断增大;同时卸荷煤岩也受到已破断关键层载荷的压实作用,从而造成覆岩卸荷膨胀总量的不断变化。将这种覆岩卸荷膨胀总量随覆岩卸荷高度动态变化的现象定义为采动覆岩卸荷膨胀累积效应,进而建立了理论模型,并通过淮北海孜煤矿巨厚火成岩下采煤覆岩裂隙实测进行了验证。结果表明,采动覆岩卸荷膨胀累积效应对采动岩层运动规律产生了重要影响,如影响覆岩关键层下离层量,影响覆岩关键层贯通破断的高度,影响不同开采条件的地表下沉系数等。采动覆岩卸荷膨胀累积效应改变了对离层存在形式的传统认识,该效应的存在导致关键层下最大离层量一般小于采高的10%,覆岩可注浆充填空间并非传统认识上的“离层区”,而主要是注浆充填压力“压实”作用下将覆岩卸荷累积膨胀所转化出的那部分空间,该发现指导了覆岩隔离注浆充填绿色开采技术的创新研发及其在建筑物压煤开采中的成功实践。     

A New Design Methodology for Time-Based Capacitance-to-Digital Converters (T-CDCs)

This paper introduces a 9-bit time-based capacitance-to-digital converter (T-CDC). This T-CDC adopts a new design methodology for parasitic cancellation with a simple calibration technique. In T-CDCs, the input sensor capacitance is first converted into a delay pulse using a capacitance-to-time converter (CTC) circuit; then this delay signal is converted into a digital code through a time-to-digital converter (TDC) circuit. A prototype of the proposed T-CDC is implemented in UMC 0.13 μm CMOS technology. This T-CDC consumes 8.42 μW and achieves a maximum SNR of 45.14 dB with a conversion time of 1 μs that corresponds to a figure of merit (FoM) of 16.4 fJ/Conv.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

基于平均功率平衡控制的磁悬浮分子泵电力失效补偿方法

高速磁悬浮涡轮分子泵（Turbo Molecular Pump, TMP）因其高能量密度、微振动、无需润滑等优点被广泛应用于工业领域，但外部电源失效时，高速转子跌落后与保护轴承产生剧烈撞击和摩擦，将给系统带来致命损害。针对以上问题，提出一种基于平均功率平衡法的电力失效补偿控制（Power Failure Compensation Control, PFCC）方法。首先，设计电机能量回馈电路；其次，对Buck-Boost变换器进行数学建模，设计一种双环非线性控制器，其中电流内环使用滑模控制，电压外环使用平均功率平衡控制（Average Power Balance Control, APBC），并利用Lyapunov函数推导出系统的稳定性条件；最后，通过搭建磁悬浮分子泵PFCC实验平台，对所提出的方法进行实验验证。结果表明：本文所提出的方法具有快速响应和输出鲁棒性，磁悬浮转子由额定转速21000 r/min降至3900 r/min时跌落，电机能量转化效率为96.6%，提高了磁轴承系统的安全性。     

Single-switch boost-buck DC-DC converter for industrial fuel cell and photovoltaics applications

The realization of dc-dc converters performs a vital function in exploiting renewable energy sources such as solar photovoltaic (PV) and fuel cell applications. This paper demonstrates a single-switch unidirectional buck-boost dc-dc converter for continuous power flow control, excluding the hybrid switched-capacitor. The proposed converter utilizes a limited number of passive components, only four diodes and three inductors required, in addition to six capacitors. The converter can operate at a wide input voltage range with continues input current. The converter has experimented under real-time conditions with 660 W PV system. The obtained efficiency ranges from 93% to 98%. Furthermore, the converter has interfaced with 550 W fuel cell operated under different fuel pressure. The realized efficiency ranges from 91% to 97%. The maximum measured inductance current ripple is limited to under 0.70 A in both scenarios, whereas 0.16 V is the maximum output voltage ripple.