Analysis of pressure and heat distribution in a dilating or contracting filter chamber with two outlets using multivariate spectral quasilinearization method

The development of efficient filters is an essential part of industrial machinery design, specifically to increase the lifespan of a machine. In the filter chamber design considered in this study, the magnetic material is placed along the horizontal surface of the filter chamber. The inside of the filter chamber is layered with a porous material to restrict the outflow of unwanted particles. This study aims to investigate the flow, pressure, and heat distribution in a dilating or contracting filter chamber with two outlets driven by injection through a permeable surface. The proposed model of the fluid dynamics within the filter chamber follows the conservation equations in the form of partial differential equations. The model equations are further reduced to a steady case through Lie's symmetry group of transformation. They are then solved using a multivariate spectral-based quasilinearization method on the Chebyshev–Gauss–Lobatto nodes. Insights and analyses of the thermophysical parameters that drive optimal outflow during the filtration process are provided through the graphs of the numerical solutions of the differential equations. We find, among other results, that expansion of the filter chamber leads to an overall decrease in internal pressure and an increase in heat distribution inside the filter chamber. The results also show that shrinking the filter chamber increases the internal momentum inside the filter, which leads to more outflow of filtrates.     

Frequency response data-based peak filter design applied to MIMO large-scale high-precision scan stage

A large-scale high-precision scan stage is important equipment in the industrial productions of micro-fabrication such as flat panel display (FPD) lithography systems. Designing controllers for multi-input multi-output (MIMO) systems is time-consuming and needs experience because of the interaction between each axis and many controller tuning parameters. The aim of this study is to develop a peak filter design method based on frequency response data to reduce repetitive disturbance. This data-based approach does not use the model and only uses the frequency response data of the controlled system and the disturbance spectrum calculated from the scanning error data (Contribution 1). The peak filter is designed by convex optimization and satisfies robust stability conditions for six-degree-of-freedom systems (Contribution 2). The control performance of the designed peak filter is experimentally demonstrated with an industrial MIMO large-scale high-precision scan stage in reducing the scanning error of the main stroke of the translation along the $x$-axis (Contribution 3).     

Subdivision based isogeometric analysis for geometric flows

We present a new isogeometric analysis (IGA) approach based on extended Loop subdivision scheme for solving various geometric flows defined on subdivision surfaces. The studied flows include the second-order, fourth-order, and sixth-order geometric flows, such as averaged mean curvature flow, constant mean curvature flow, and minimal mean-curvature-variation flow, which are generally derived by minimizing the associate energy functionals with $L^2$-gradient flow respectively. The geometric flows are discretized by means of subdivision based IGA, where the finite element space is formulated by the limit form of the extended Loop subdivision for different initial control meshes. The basis functions, consisting of quartic box-splines corresponding to each subdivided control mesh, are utilized to represent the geometry exactly. For the cases of the evolution of open surfaces with any shape boundary, high-order continuous boundary conditions derived from the mixed variational forms of the geometric flows should be implemented to be consistent with the isogeometric concept. For time discretization, we adopt an adaptive semi-implicit Euler scheme. By several numerical experiments, we study the convergence behaviors of the proposed approach for solving the geometric flows with high-order boundary conditions. Moreover, the numerical results also show the accuracy and efficiency of the proposed method.     

GO/PI复合纳米纤维的制备及其过滤性能研究

为制备高过滤效率、低过滤阻力的空气过滤材料,将氧化石墨烯纳米颗粒(GO)掺杂到聚酰亚胺(PI)纺丝溶液中,制备氧化石墨烯/聚酰亚胺(GO/PI)复合纳米纤维过滤材料。通过观察其形貌、过滤性能来确定最优纺丝工艺参数。结果表明:当PI质量分数为30%,GO质量分数为1%,纺丝电压为25 kV,接收距离为20 cm时,复合纳米薄膜的纤维形貌较好,过滤性能优良。与PI纯组分纳米纤维过滤材料相比,GO/PI复合纳米纤维过滤材料的过滤性能更好,制得GO/PI复合纳米纤维膜的平均孔径为1.8μm,过滤效率为99.68%,过滤阻力仅为85.35 Pa。     

采煤机惯性导航定位动态零速修正技术

基于捷联惯性导航与轴编码器组合的采煤机惯性导航定位是综采工作面可行的采煤机定位技术。惯性导航提供姿态角参数，轴编码器提供速度参数，采煤机惯性导航定位利用航位推算算法解算出东北天坐标系下的位置坐标。为了进一步提高定位精度，在消除确定性偏差的基础上，根据惯性导航姿态误差方程，以东、北、天3个方向的平台失准角为状态量构建状态方程，根据动态零速修正技术的非完整约束条件，以采煤机坐标系横向和垂直方向速度值为观测量构建量测方程，建立卡尔曼滤波模型，并进行移动平台模拟采煤机运行试验验证。在试验条件下，第3刀导航东、北方向最大误差分别由0.639 7，0.856 7 m减小为0.456 4，0.594 2 m。第4刀导航东、北方向最大误差分别由0.644 4，0.910 6 m减小为0.466 5，0.603 0 m。东、北方向定位精度提升了30%。     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.     

A broadband filter with two transmission zeros adopting a new design method

A new design method was proposed in this article to insert transmission zeros in the broadband filters. In this method, the coupling line was connected to a certain position on the resonator. And then the coupling strength was adjusted by the connecting position. The open end of the resonator was hung and then the cross‐coupling was introduced to realize transmission zeros. This coupling method could add an adjustable parameter to improve the freedom of design and convenient to insert the transmission zeros. To verify this method, a highly selective coupled‐line microstrip filter with two transmission zeros was designed, fabricated, and measured. The measured results were in good agreement with the simulated ones. The return and insertion losses of the broadband filter were better than 18 and 2 dB, respectively. The relative bandwidth of the filter (FBW) was more than 68%. The rectangular coefficient (30 dB:1 dB) was less than 1.21.     

Passive target detection and tracking from electromagnetic field measurements

This paper presents a novel approach to the localization of moving targets in a complex environment based on the measurement of the perturbations induced by the target presence on an independently‐generated time‐varying electromagnetic field. Field perturbations are measured via a set of sensors deployed over the domain of interest and used to detect and track a possible target by resorting to a particle Bernoulli filter (PBF). To comply with real‐time operation, the PBF works along with an artificial neural network (ANN) model of the environment trained offline via finite elements (FEs). The performance of the proposed algorithm is assessed via simulation experiments.     

Microwave bandpass filter by feedback interference topology

This paper proposes a signal feedback interference topology to control the characteristics of a coupled line bandpass filter. Control is carried out by varying the ratio of the transmission line parameters of the forward and the feedback couplers. The topology produces a compact filter that does not require a complicated design or fabrication. The results of the insertion and return losses show that the feedback‐controlled design has desirable features in terms of the design frequency, fractional bandwidth, stopband rejection level, roll‐off rate and insertion loss. The test results of the fabricated prototype achieved good agreement with the simulation results of the ideal transmission line design model. Several microwave, modern wireless and mobile/satellite communication systems may benefit from such a filter design due to its compactness and flexibility.