Fluid sloshing thermo-mechanical characteristic in a cryogenic fuel storage tank under different gravity acceleration levels

Fluid sloshing usually causes serious safety issues on the dynamic stability and propellant thermal management during the powered-flight phase of launch vehicle. With the wide using of cryogenic propellants, the coupled thermo-mechanical performance during fluid sloshing becomes more prominent. In the present study, one numerical model is established to simulate fluid sloshing by using the VOF method coupled with the mesh motion treatment. The phase change occurring within the tank is considered. Both the experimental validation and mesh sensitivity analysis are made. It shows that present numerical model is acceptable. Based on the developed numerical model, the effect of different super gravity accelerations on fluid sloshing hydrodynamic characteristic is numerically researched. The fluid pressure variation, the sloshing force and sloshing moment, the interface dynamic response and the interface shape variation are investigated, respectively. It shows that the gravity acceleration has caused obvious influences on fluid sloshing characteristic. When the gravity acceleration is higher than 4g₀, fluid sloshing becomes more obvious and must be paid enough attention. With some valuable conclusions obtained, the present work is of great significance for in-depth understanding of fluid sloshing mechanism.     

Effects of an inhomogeneous electron density distribution on the hydrogen distribution in TiZrTaNbAl multi-principal element alloys

A body-centered cubic equiatomic TiZrTaNbAl multi-principal element alloy (MPEA) with elemental fluctuations was investigated to further understand the relationship between the microstructure and hydrogen distribution. In this study, a composition dependence of the hydrogen distribution was observed in the TiZrTaNbAl MPEA. An inhomogeneous electron density distribution of the MPEA was revealed by advanced differential phase-contrast scanning electron microscopy (DPC-STEM) for the first time. The results showed that the electron density has a significant effect on the hydrogen distribution in TiZrTaNbAl MPEAs. This work provides new insight into the design of materials with high hydrogen storage capacity and high hydrogen embrittlement resistance.     

Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

Experimental investigations of enhanced glow based on a pulsed hollow-cathode discharge

In this work, the pulsed hollow cathode discharges at low pressure argon with an axial magnetic field were studied. The results indicate that the pulsed discharge is operated in an enhanced glow(EG) mode. Under the same conditions, the discharge current of the pulsed discharge is two or three orders higher than that of the direct current discharge. The spatial and temporal evolution of the light emission shows that, the current fluctuation at the rising edge of the pulse plays an important role for the EG discharge of pulsed hollow cathode, which forms a high-density, highcurrent and long-distance plasma column outside the cavity.     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

A system for time-fluctuating flow rate measurements in a single-blade pump circuit

Commonly used flow rate measurement systems provide an accurate and stable output value of the quasi-stationary flow rate. In some pump types as e.g. single-blade pumps significant flow rate fluctuations may occur even in steady operation points due to rotor-stator interaction. For the analysis of the time-resolved flow rate a new measurement and evaluation method is presented based on an electromagnetic flow meter. Internal averaging of the flow meter is deactivated and the raw signal is evaluated directly with a sampling rate of 3 kHz. With ensemble-averaging in combination with an impeller position detection, interfering signals acting on the time-resolved measurement signal are filtered out. Accompanying numerical simulations of the pump flow circuit are carried out with a 1D method of characteristics and validated against well-established time-resolved pressure measurements of the pump flow. Experiment and simulation show a resembling trend of pressure as well as flow rate fluctuations over the entire operation range of the pump. Thus, by the combined utilisation of measurement and simulation technique, we assure the validity of the ensemble-averaged flow rate fluctuation results. We find that the flow rate fluctuations show a consistent phase shift to the pressure fluctuations that increases towards overload. The flow rate amplitude is an order of magnitude smaller than the amplitude of the pressure fluctuations.     

摇摆运动下多环路主冷却剂系统自然循环流量的稳定性分析

海洋核动力平台因其突出的安全性已成为当今核能领域热点研究问题之一，但在海洋等非惯性条件下会使一回路系统的热工特性发生变化。针对此问题，本文对几种典型的一回路系统在摇摆条件下的自然循环流量波动特性进行计算分析。分别建立典型的双环路、三环路、四环路的一回路系统模型布置方案，并同时考虑摇摆中心的位置，根据流体动量守恒方程，得到不同状态下一回路系统内的流量变化规律。对于单堆双环路系统，摇摆中心在船上/中/下部位置时，环路流量波动幅度分别为13.2%/11.2%/9.5%，堆芯流量波动幅度分别为0.9%/0.8%/0.6%；对于单堆三环路系统，摇摆中心在船下部时，环路流量和堆芯流量波动幅度分别为9.2%和0.8%；对于单堆四环路系统，摇摆中心在船下部时，布置方案1和方案2的环路流量波动幅度分别为9.5%和9.2%，堆芯流量波动幅度分别为0.9%和0.7%。计算结果表明：采用单堆双环路的设计布置方案是最有利于系统稳定性的。     

Effect of background fluctuation on velocity diagnostics by Mach probe

The effect of background fluctuation on velocity diagnostics is discussed and studied. The kinetic theory of Mach probe (MP) and the theory of BGK mode are combined to evaluate how the measurement of MP is affected by electrostatics fluctuation. It is found that the quantity of speed by the MP model is closer to the effective velocity in the picture of momentum flux rather than the real mean velocity, while, with high fluctuation, the fitting parameter of MP's exponential formula should be corrected.     

电动汽车的双向DC-DC变换器多模态控制方法

针对当前电动汽车功率控制过程中存在负载跳变抗干扰性能差、响应速度较慢等问题,提出一种应用于电动汽车的双向DC-DC变换器多模态控制方法。文章详细分析了电动汽车双向DC-DC变换器的拓扑结构和升降压控制模式;结合不同工况下的变换器工作状态,分析电压和电流模式控制,得出其电压、电流开闭环函数;利用多模态控制方法,由变换器的功能控制单元下达电压、电流环给定信号来实现功率波动平抑控制;在MATLAB中搭建了仿真模型。仿真结果表明,文章所提出的控制方法能够较好地实现双向DC-DC变换器的功率波动平抑功能,具有稳定性好、对负载跳变抗干扰性能强、响应速度快的特点。     

Classification and identification of gas–liquid dispersion states in a jet bubbling reactor

Three gas–liquid dispersion states including flooding, loading, and complete dispersion are observed sequentially in a jet bubbling reactor with an increase of the liquid jet velocity at the nozzle outlet (u_j). The gas–liquid dispersion states are identified through the slope (k) of the curve of fluctuation distribution index (FI) versus u_j as follows: (a) under the flooding, k = 0; (b) under the loading, k > 0; (c) under the complete dispersion, k < 0. In particular, the u_j at the transition points from flooding to loading and from loading to complete dispersion are referred to flooding jet velocity (u_jf, the transition point between k = 0 and k > 0) and complete dispersion jet velocity (u_jcd, the transition point from k > 0 to k < 0), respectively. The average relative deviations of the u_j at the transition points obtained through the acoustic emission measurement and visual observation are less than 5%.