Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

An adaptive sliding mode observer based near-optimal OER tracking control approach for PEMFC under dynamic operation condition

Tracking control of oxygen excess ratio (OER) is crucial for dynamic performance and operating efficiency of the proton exchange membrane fuel cell (PEMFC). OER tracking errors and overshoots under dynamic load limit the PEMFC output power performance, and also could lead oxygen starvation which seriously affect the life of PEMFC. To solve this problem, an adaptive sliding mode observer based near-optimal OER tracking control approach is proposed in this paper. According to real time load demand, a dynamic OER optimization strategy is designed to obtain an optimal OER. A nonlinear system model based near-optimal controller is designed to minimize the OER tracking error under variable operation condition of PEMFC. An adaptive sliding mode observer is utilized to estimate the uncertain parameters of the PEMFC air supply system and update parameters in near-optimal controller. The proposed control approach is implemented in OER tracking experiments based on air supply system of a 5 kW PEMFC test platform. The experiment results are analyzed and demonstrate the efficacy of the proposed control approach under load changes, external disturbances and parameter uncertainties of PEFMC system.     

Simple and novel synthesis of zirconia whiskers from a phosphate flux

High quality zirconia whiskers have been successfully prepared by molten salt method, using zirconium oxychloride (ZrOCl₂·8H₂O) and sodium phosphate tribasic dodecahydrate (Na₃PO₄·12H₂O) as precursor and molten salt, respectively. The effects of types of molten salt and heat treatment temperature on the formation of zirconia whiskers were characterized by XRD, Raman, DTA-TG, FE-SEM, TEM, SAED and HR-TEM. When Na₃PO₄·12H₂O is utilized as molten salt and the heat treatment temperature is 900?°C, the as-prepared zirconia whiskers with length ranging from 4?µm to 8?µm show an average aspect ratio of 25. The obtained ZrO₂ whiskers with monoclinic structure are elongated along [010] direction and exhibit a smooth surface with no distinct defects. The XRD and Raman results reveal that the phase transformation from tetragonal zirconia to monoclinic zirconia occurs with the increased crystal size and the water quenching treatment can significantly reduce the content of sodium zirconium phosphate [Na_9–4×Zr_x(PO₄)₃] in the final product. The growth mechanism of zirconia whiskers is supposed to be a dissolution-precipitation process. Since the sodium zirconium phosphate [Na_9–4×Zr_x(PO₄)₃] effectively promotes the dissolution of zirconia in liquid molten salt, zirconia can grow into zirconia whiskers according to its anisotropy.     

Structure and crystallization behavior of complex mold flux glasses in the system CaO-Na2O-Li2O-CaF2-B2O3-SiO2: A multi-nuclear NMR spectroscopic study

The structure of mold flux glasses in the system CaO-(Na,Li)₂O-SiO₂-CaF₂ with unusually high modifier contents, stabilized by the addition of ∼4 mol% B₂O₃, is studied using ⁷Li, ²³Na, ¹⁹F, ¹¹B, and ²⁹Si magic-angle-spinning (MAS), and ⁷Li{¹⁹F} and ²³Na{¹⁹F} rotational echo double-resonance (REDOR) nuclear magnetic resonance (NMR) spectroscopy. When taken together, the spectroscopic results indicate that the structure of these glasses consists primarily of dimeric [Si₂O₇]⁻⁶ units that are linked to the (Ca,Na,Li)-O coordination polyhedra, and are interspersed with chains of corner-shared BO₃ units. The F atoms in the structure are exclusively bonded to Ca atoms, forming Ca(O,F)_n coordination polyhedra. This structural scenario is shown to be consistent with the crystallization of cuspidine (3CaO·2SiO₂·CaF₂) from the parent melts on slow supercooling. The progressive addition of Li to a Na-containing base composition results in a corresponding increase in the undercooling required for the nucleation of cuspidine in the melt, which is attributed to the frustrated local structure caused by the mixing of alkali ions.     

Effect of Li2O on the crystallization behavior of CaO-Al2O3-SiO2-Li2O-Ce2O3 mold slags

The effect of Li₂O on the crystallization properties of CaO-Al₂O₃-SiO₂-Li₂O-Ce₂O₃ slags was investigated. With increasing the Li₂O content, LiAlO₂ and CaCeAlO₄ were the main crystalline phases. LiAlO₂ formed for the charge compensating of Li⁺ ions to [AlO₄^5?]-tetrahedrons, and CaCeAlO₄ formed as a result of the charge balance of Ce³⁺ ions, Ca²⁺ ions, and [AlO₆^9?]-octahedrons. Increasing the content of Li₂O to 10%, the crystallization temperature was the highest, and the incubation time was the shortest. The crystallization ability was strong due to the three factors of strengthening the interaction between ions and ion groups, decreasing the polymerization degree, and increasing the melting temperature. Further increasing the content of Li₂O, the crystallization performance was obviously suppressed, because the melting temperature and the force between the cations and the anion groups decreased.     

冠状动脉系统的微分积分终端滑模混沌抑制

冠状动脉系统的混沌现象会导致严重的健康问题。以非线性冠状动脉系统为研究对象，建立了不确定性冠状动脉系统动力学模型，提出了不确定性冠状动脉系统的微分积分终端滑模混沌抑制方法，针对该模型的不确定性设计了扰动观测器，根据Lyapunov理论证明了所设计控制系统的稳定性，通过仿真实验验证了所提出的混沌抑制方法的有效性和可行性。     

Flame extension and the near field under the ceiling for travelling fires inside large compartments

Structures need to be designed to maintain their stability in the event of a fire. The travelling fire methodology (TFM) defines the thermal boundary condition for structural design of large compartments of fires that do not flashover, considering near field and far field regions. TFM assumes a near field temperature of 1200°C, where the flame is impinging on the ceiling without any extension and gives the temperature of the hot gases in the far field from Alpert correlations. This paper revisits the near field assumptions of the TFM and, for the first time, includes horizontal flame extension under the ceiling, which affects the heating exposure of the structural members thus their load-bearing capacity. It also formulates the thermal boundary condition in terms of heat flux rather than in terms of temperature as it is used in TFM, which allows for a more formal treatment of heat transfer. The Hasemi, Wakamatsu, and Lattimer models of heat flux from flame are investigated for the near field. The methodology is applied to an open-plan generic office compartment with a floor area of 960 m² and 3.60 m high with concrete and with protected and unprotected steel structural members. The near field length with flame extension (fTFM) is found to be between 1.5 and 6.5 times longer than without flame extension. The duration of the exposure to peak heat flux depends on the flame length, which is 53 min for fTFM compared with 17 min for TFM, in the case of a slow 5% floor area fire. The peak heat flux is from 112 to 236 kW/m² for the majority of fire sizes using the Wakamatsu model and from 80 to 120 kW/m² for the Hasemi and Lattimer models, compared with 215 to 228 kW/m² for TFM. The results show that for all cases, TFM results in higher structural temperatures compared with different fTFM models (600°C for concrete rebar and 800°C for protected steel beam), except for the Wakamatsu model that for small fires, leads to approximately 20% higher temperatures than TFM. These findings mitigate the uncertainty around the TFM near field model and confirm that it is conservative for calculation of the thermal load on structures. This study contributes to the creation of design tools for better structural fire engineering.     

Effect of storage time and temperature on hydrogen fermentation of food waste

Practically, before being fed to the treatment plant, food waste (FW) is stored for up to a week in a storage tank under ambient temperature condition, which would have an impact on the bioenergy yield. In the present work, FW was stored at different temperatures (5 °C, 20 °C, and 35 °C) for 0 d, 1 d, and 2 d, and it was used as a feedstock for mesophilic H₂ fermentation. H₂ production curves were divided by three groups, finally attaining 1.7–1.8 mol H₂/mol hexose_added, 1.4–1.5 mol H₂/mol hexose_added, and 1.2 mol H₂/mol hexose_added, achieved from the (fresh, FW stored at 5 °C), (FW stored at 20 °C, and 35 °C for 1 d), and (FW stored at 35 °C for 2 d), respectively. The different performance was attributed to the growth of indigenous lactic acid bacteria such as Lactobacillus and Weissella during storage under high temperature condition. In addition, it was found that the activity of homoacetogenic reaction (R17, 4H₂ + CO₂ → Acetate) calculated by establishing metabolic flux balance was different depending on the H₂ production performance. The flux of R17 ranged 0.03–0.06 under low H₂ yield achieved conditions, while it increased to 0.10–0.17 those showing low H₂ yields.     

An Improved Torque Sensorless Speed Control Method for Electric Assisted Bicycle With Consideration of Coordinate Conversion

In this paper, we propose an improved torque sensorless speed control method for electric assisted bicycle, this method considers the coordinate conversion. A low-pass filter is designed in disturbance observer to estimate and compensate the variable disturbance during cycling. A DC motor provides assisted power driving, the assistance method is based on the real-time wheel angular velocity and coordinate system transformation. The effect of observer is proved, and the proposed method guarantees stability under disturbances. It is also compared to the existing methods and their performances are illustrated through simulations. The proposed method improves the performance both in rapidity and stability.      

油气管道缺陷漏磁检测有限元模拟

为了研究油气管道缺陷的漏磁信号特征，基于漏磁检测技术基本原理，采用有限元方法，应用ANSYS软件对含裂纹和气孔缺陷管道磁化后产生的漏磁场进行模拟仿真，得到了描述漏磁场特征的磁通密度径向和轴向分布曲线。通过改变裂纹和气孔的尺寸，得出这两种缺陷形式不同尺寸下的漏磁场分布规律。结果表明，随着裂纹深度增加，磁通密度径向、轴向分量的峰值强度均明显增大；在距管壁表面相同深度下，气孔缺陷磁通密度的峰值随孔径增加而显著增大；相同孔径时，气孔距表面越近，漏磁信号越强。为管道漏磁检测过程中的裂纹和气孔缺陷的特征识别提供了理论基础和实践依据。