One-step to prepare high-performance gas diffusion layer (GDL) with three different functional layers for proton exchange membrane fuel cells (PEMFCs)

Gas diffusion layer (GDL) is one of the most important components of fuel cells. In order to improve the fuel cell performance, GDL has developed from single layer to dual layers, and then to multiple layers. However, dual or multi layers in GDL are usually prepared by layer-by-layer methods, which cost too much time, energy, and resources. In this work, we successfully developed a facile one-step method to prepare a GDL with three functional layers by utilizing the different sedimentation rates and filtration rates of short carbon fiber (CF) and carbon nanotube (CNT). The treatment temperature for this GDL is much lower than that of traditional method. The thickness of the GDL can be effectively controlled from as thin as 50 μm to more than 200 μm by simply adjusting the content of CF. The GDL with high flexibility is suitable to develop high performance flexible electronics. The fuel cell with the GDL has the maximum power density 1021 mW cm^?2, which shows 19% improvement comparing to the conventional one. Therefore, this work breaks the traditional concept that GDL for fuel cells only can be prepared by very complex and high-cost procedure.     

The impact of the thermal treatment during ink preparation on the ionomer-supported catalyst interactions in the catalyst layers

Catalyst slurries (inks) were prepared with and without thermal treatment to determine the support/ionomer structures and interactions in the catalyst layer (CL) which impact on membrane electrode performance and durability. The thermal treatment of the ink has a nominal effect on the ionomer/support structure in which the carbon support is non-graphitised. The agglomerate/aggregate structures have a high degree of support/ionomer interface and sufficient macroporosity for water movement in the CL. This improves the membrane electrode assembly (MEA) performance, but also accelerates electrochemical carbon degradation. Thermal treatment of graphitised support-containing inks resulted in increased performance facilitated by a larger support/ionomer interface. Without thermal treatment, the more hydrophobic support would form aggregate structures in which water contact was restricted, limiting proton transfer, isolating catalyst, decreasing performance. The water limited access, would however, prolong stability during accelerates carbon degradation. The electrochemical properties were studied using full and half MEA cells.     

The origin of interfacial delamination in Au/ceramic cofired LTCC structure

The interfacial delamination of electrode/ceramic multilayer structure will seriously damage the reliability of low temperature co-fired ceramic (LTCC) module in practical applications. In this work, three kinds of glasses employed in Au electrode are designed and prepared to study the abnormal expansion and delamination process in the Au/ceramic LTCC multilayer structure. The interfacial delamination in the co-fired structure is found to be attributed to the abnormal expansion of glass in respect to Au electrode at high temperature, which is originated from the enlarged closed pores during the co-firing process. This conclusion is further confirmed by co-firing the sample in a low-pressure condition. The mechanism and elimination of interfacial delamination here provides a feasible solution for the design of novel glasses in Au electrode for LTCC applications.     

电气设备接地装置的运行与维护探讨

随着现代化进程的加快,电气设备接地装置的应用越来越广泛,从安全的角度考虑,其运行和维护受到了全社会的广泛关注,如何介绍应用当中存在的安全隐患成为当前关注的主要内容。本文系统概括的分析了电气设备接地装置的运行和维护情况,为其安全应用提供一定的参考。     

High ultraviolet transparent conducting electrodes formed using tantalum oxide/Ag multilayer

We investigated the optical and electrical properties of Ta₂O₅/Ag/Ta₂O₅ films as functions of the thicknesses of the Ta₂O₅ and Ag layers. It was found that with an increase in the thicknesses of the Ta₂O₅ and Ag layers from 10 to 40 nm and from 12 to 24 nm, respectively, the sheet resistance, carrier concentration, electron mobility, and resistivity of the Ta₂O₅/Ag/Ta₂O₅ film varied from 2.02 to 8.95 Ω/sq, 5.74 × 10²¹ to 2.92 × 10²² cm^–3, from 13.21 to 24.07 cm²/V·s, and from 8.89 × 10^-6 to 8.24 × 10^-5 Ω cm, respectively. The average transmittance (T_av) of the multilayer samples ranged from 57.18% to 93.99%, and it depended on the Ta₂O₅ and Ag layer thicknesses. The highest T_av of 93.99% was observed for the film with 35 nm thick Ta₂O₅ and 18 nm thick Ag layers, and the peak Haacke's figure of merit (157.04 × 10^–3 Ω^–1) was obtained for 20 nm thick Ta₂O₅ and 21 nm thick Ag layers. Ta₂O₅ (100 nm) and Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) samples had optical bandgaps of 4.70 and 4.45 eV, respectively. Film Wizard simulations were conducted to understand the dependence of the transmittance of the multilayer on the thicknesses of the Ta₂O₅ and Ag layers, and phasor analyses were performed to determine how the transmittance of the Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) film depended on the Ta₂O₅ layer's thickness.     

基于多层感知器的气液两相流流型识别方法

通过对电阻层析成像数据采集原理和深度学习网络的研究,提出了一种基于阵列电阻值和多层感知器深度学习网络相结合的流型识别方法。利用电阻层析成像系统中的16个电极传感器来获取流型样本数据,并构建出流型识别数据库,然后对多层感知器深度学习网络进行训练,获得可以识别不同流型的网络。实验结果表明,采用阵列电阻值结合多层感知器网络对流型进行学习和识别的方法,流型识别准确率可以达到95%,解决了流型图像生成过程与数据特征预选过程中流型特征损失的问题,流型识别性能得到了提高。     

Study on estimating electric potential in space between parallel electrodes

We have been studying on estimating distribution of permittivity between measurement electrodes using capacitance and electric potential. Two arc electrodes were separated by long distance and there electrodes were surrounded by additional electrodes respectively. In past research work, we carried out numerical electric analysis for calculating the capacitance and electric potential using Finite Element Method (FEM) and compared with experimental and numerical results. The capacitance values were almost agreed with experimental and numerical results. However, the electric potential values were different between experimental and numerical results in conventional studies. In this paper, we proposed an equivalent circuit including the stray capacity and measurement method for capacitance, the electric potential in space between long distance electrodes was estimated.     

Simulation studies on a rotating ring disk electrode: Effects of ionic migration with kinetic complication-disk results

In continuation to my previous work (Guha S. AIChE J. 2013;59(4):1390-1399), in this work, effects of ionic migration are evaluated for disk region of a rotating ring disk electrode system by numerically solving complex differential equations, developed for mass transfer along with kinetic complication in presence of ionic migration under limiting current condition. The system for simulation is 0.01 M Fe₂(SO₄)₃ solution with H₂SO₄ as supporting electrolyte. Simulation cases are presence and absence of ionic migration with kinetic complication (oxidation of Fe²⁺ to Fe³⁺ under O₂ pressure). Results show that concentration boundary layer thickness of reactant Fe³⁺ reduces appreciably and steady-state disk current reduces substantially in presence of migration. Simulated steady-state disk current in absence of migration case agrees well with published data. Results indicate higher Fe²⁺ concentration in presence of migration and thereby higher rate of oxidation of Fe²⁺ to Fe³⁺ at all rate constant values.