工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Influence of pressure and dwell time on pressure-assisted sintering of calcium cobaltite

Calcium cobaltite Ca₃Co₄O₉, abbreviated Co349, is a promising thermoelectric material for high-temperature applications in air. Its anisotropic properties can be assigned to polycrystalline parts by texturing. Tape casting and pressure-assisted sintering (PAS) are a possible future way for a cost-effective mass-production of thermoelectric generators. This study examines the influence of pressure and dwell time during PAS at 900°C of tape-cast Co349 on texture and thermoelectric properties. Tape casting aligns lentoid Co349. PAS results in a textured Co349 microstructure with the thermoelectrically favorable ab-direction perpendicular to the pressing direction. By pressure variation during sintering, the microstructure of Co349 can be tailored either toward a maximum figure of merit as required for energy harvesting or toward a maximum power factor as required for energy harvesting. Moderate pressure of 2.5 MPa results in 25% porosity and a textured microstructure with a figure of merit of 0.13 at 700°C, two times higher than the dry-pressed, pressureless-sintered reference. A pressure of 7.5 MPa leads to 94% density and a high power factor of 326 µW/mK² at 800°C, which is 11 times higher than the dry-pressed reference (30 MPa) from the same powder.     

Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

二苯氨基脲分光光度法测定饮水机热罐中六价铬含量

为了探讨饮水机热罐水中浸出六价铬的含量,采用快速测定六价铬含量的方法:二苯氨基脲分光光度法。试验中对样品进行平行处理并测定浸泡水中六价铬含量,评价热罐水中六价铬的浸出量。结果表明,使用该方法测定饮水机热罐中六价铬含量很稳定,曲线线性良好,线性回归方程为I=0.761 2c+0.002 5,R²=0.999 93,饮水机中热罐浸出六价铬含量为0.010 mg/L。该法对输配水设备产品中浸出六价铬含量的测定具有一定的指导意义。     

Effect of different control strategies on rapid cold start-up of a 30-cell proton exchange membrane fuel cell stack

Many places experience extreme temperatures below −30 °C, which is a great challenge for the fuel cell vehicle (FCV). The aim of this study is to optimize the strategy to achieve rapid cold start-up of the 30-cell stack at different temperature conditions. The test shows that the stack rapidly starts within 30 s at an ambient temperature of −20 °C. Turning on the coolant at −25 °C show stability of the cell voltage at both ends due to the end-plate heating, however, voltage of intermediate cells fluctuates sharply, and successful start-up is completed after 60 s. The cold start strategy changes to load-voltage cooperative control mode when the ambient temperature reduced to −30 °C, the voltage of multiple cells in the middle of the stack fluctuate more drastic, and start-up takes 113 s. The performance and consistency of the stack did not decay after 20 cold start-up experiments, which indicates that our control strategies effectively avoided irreversible damage to the stack caused by freeze-thaw process.     

Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

热轧圆钢热顶锻裂纹原因分析

热顶锻合格率是反映热轧圆钢实物质量的一个重要指标。在对国内外热轧圆钢热顶锻质量控制研究成果综述的基础上，对热轧圆钢的热顶锻质量进行了全面的调查、统计和试验研究，归纳了引起热轧圆钢热顶锻裂纹的常见原因，介绍了热顶锻裂纹分析步骤。通过对热顶锻裂纹的形貌和金相组织进行分析，阐述了引起热顶锻裂纹的冶炼因素和轧制因素，并进行了举例说明。     

A new solid‐state mode of hot corrosion at temperatures below 700°C

Preliminary results on a single‐crystal nickel‐based superalloy indicated that hot corrosion can occur at temperatures as low as 550°C, where liquid formation, generally believed to be responsible for Type II hot corrosion, is not predicted. Additional tests were conducted on pure‐nickel samples at 650°C and below to more clearly elucidate the mechanism of this very low‐temperature hot corrosion. Environments in dry air and O₂‐(2.5, 10, 100, and 1000) ppm SO₂ were studied. Based on the results obtained, a solid‐state corrosion mechanism was inferred. The mechanism relies on the formation of a previously unreported compound phase, which was identified using transmission electron microscope analysis that indicated the stoichiometry of Na₂Ni₂SO₅. Furthermore, it was nanocrystalline in structure and metastable. It was deduced that the Na₂Ni₂SO₅ formation was responsible for the rapid nickel transport required for the observed accelerated corrosion process. Moreover, its eventual decomposition resulted in a mixed product of porous NiO with embedded particles of Na₂SO₄. Application of the proposed mechanism to nickel‐based alloys is discussed.     

Failure mechanism of MCrAlY coating at the coating‐substrate interface under type I hot corrosion

MCrAlY coatings are widely used to provide protection of hot component in modern gas turbine engines against high‐temperature oxidation and hot corrosion. Coating‐substrate interface, where the substrate is only partially covered by the ?coatings, is vulnerable to the hot corrosion attack. The accelerated degradation at the coating‐substrate interface can cause fast spallation of the coating, leading to the early failure of the gas turbine components. In this paper, MCrAlY powder was deposited on IN792 disks by high‐velocity oxygen‐fuel spraying. The hot corrosion behavior of the coated sample was investigated using (0.8Na, 0.2K)₂SO ₄ salt deposition at 900°C in lab air. Results showed a minor attack in the coating center, however, an accelerated corrosion attack at the coating‐substrate interface. The fast growth of corrosion products from substrate caused large local volume expansions at the coating‐substrate interface, resulting in an early coating spallation.