Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Microcrack healing in zirconia ceramics under a DC electric field/current

Flash event caused by a DC electric field/current was applied to the crack healing in 8 mol % Y₂O₃ stabilized cubic ZrO₂ polycrystals (8Y-CSZ). The flash event, which occurred by applying the DC power higher than a critical value of 100 mW/mm³, successfully healed the microcrack within several minutes without any healing agents at a furnace temperature of 800 °C. As compared to the healing treatment under static annealing, the healing phenomena were accelerated about 2 times under the flash treatment even at the same temperatures, suggesting that the enhanced healing phenomena cannot be explained only by the temperature effect. Since the rate of grain growth was accelerated under the flash treatment, the flash healing would be accelerated through the current-enhanced diffusional processes. This study shows for the first time that the flash event has a potential to apply to the crack healing process in the ceramic materials and composites.     

木质纤维与水泥共同改良软土的力学性能与微观机制分析

通过压实试验、无侧限抗压强度试验和劈裂试验,分析不同木质纤维含量、水泥含量和固化时间对软土力学性能的影响规律,探讨木质纤维、水泥改良软土的微观机制。结果表明,木质纤维的加入对水泥改良软土的击实特性有显著的影响;木质纤维与水泥可有效改善土体的抗压和劈裂抗拉强度,随着木质纤维含量的增加,改良土的抗压和劈裂抗拉强度呈现出明显的“驼峰”现象,并在木质纤维含量为0.25%时最大;木质纤维与水化产物、软土颗粒形成互锁效应,增大了改良土的摩擦力,同时木质纤维还承担一定的拉伸强度,使改良土的劈裂强度增加。     

FeOOH–CoS composite catalyst with high catalytic performances for oxygen evolution reaction at high current density

Water electrolysis is an efficient approach for high-purity hydrogen production. However, the anodic sluggish oxygen evolution reaction (OER) always needs high overpotential and thus brings about superfluous electricity cost of water electrolysis. Therefore, exploiting highly efficient OER electrocatalysts with small overpotential especially at high current density will undoubtedly boost the development of industrial water electrolysis. Herein, we used a simple hydrothermal method to prepare a novel FeOOH–CoS nanocomposite on nickel foam (NF). The as-prepared FeOOH–CoS/NF catalyst displays an excellent OER performance with extremely low overpotentials of 306 and 329 mV at 500 and 1000 mA cm⁻² in 1.0 M KOH, respectively. In addition, the FeOOH–CoS/NF catalyst can maintain excellent catalytic stability for more than 50 h, and the OER catalytic activity shows almost no attenuation no matter after 1000 repeated CV cycles or 50 h of stability test. The high catalytic activity and stability have exceeded most non-noble metal electrocatalysts reported in literature, which makes the FeOOH–CoS/NF composite catalyst have promising applications in the industrial water electrolysis.     

Influence of anode current density on carbon parasitic reactions during electrolysis

In the electro-deoxidation process, carbon parasitic reaction (CO₃^2- + 4e^-=C + 3O^2-) usually occurs when using carbon materials as the anode, which leads to increase of the carbon content in the final metal and decrease of the current efficiency of the process. The aim of this work is to reduce the negative effect of carbon parasitic reaction on the electrolysis process by adjusting anode current density. The results indicate that lower graphite anode area can achieve higher current density, which is helpful to increase the nucleation site of CO₂ bubbles. Most of CO₂ would be released from the anode instead of dissolution in the molten CaCl₂ and reacting with O^2- to form CO₃^2-, thus decreasing the carbon parasitic reaction of the process. Furthermore, the results of the compared experiments show that when the anode area decreases from 172.78 to 4.99 cm², CO₂ concentration in the released gases increases significantly, the carbon mass content in the final metal product decreased from 1.09% to 0.13%, and the current efficiency increased from 6.65% to 36.50%. This study determined a suitable anode current density range for reducing carbon parasitic reaction and provides a valuable reference for the selection of the anode in the electrolysis process.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

微型土压平衡盾构机液压系统故障分析

以微型土压平衡(Earth Pressure Balance,EPB)盾构机推进液压系统作为研究对象,介绍了推进系统的工作原理,对混入空气后的油液黏度和有效体积弹性模量进行分析,建立了推进系统数学模型,并对混入不同百分比空气的系统进行仿真运算,得到了液压缸位移响应和速度响应随系统含气量变化的关系。研究表明:随着液压系统空气含量的增加,液压缸位移响应发生迟滞,速度响应变慢,液压缸在运动时产生振动。结合各液压元件工作原理,依次对实际盾构机推进系统元件进行排气,最终排除了液压系统中混入的空气,为实现盾构机平稳推进提供了理论依据。     

我国中空吹塑行业发展现状及“十四五”期间重点产品、工艺和设备发展方向

从原料、中空成型机和吹塑工艺等方面介绍了我国中空吹塑行业发展现状，并对电子化学品专用超洁净桶、高压储氢四型瓶、全电动中空成型机、微发泡中空成型技术和挤吹聚对苯二甲酸乙二醇酯（PET）容器等在“十四五”期间的重点产品、工艺和设备发展方向进行了展望。