Laser damage resistance of plasma-sprayed alumina and honeycomb skeleton/alumina composite ceramic coatings

Al₂O₃ and honeycomb skeleton-Al₂O₃ composite coatings on Titanium alloy (Ti–6Al–4V) were prepared by atmospheric plasma spraying. A laser ablation experiment on as-sprayed coatings was performed. In this paper, the laser damage resistance, microstructure, phase composition of Al₂O₃ coatings were examined. 3D Dimensional Confocal Microscopy, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and Energy Dispersive Spectrometry (EDS) characterized the laser damage morphology, microstructure, phase composition, and element analysis, respectively. The influence of the honeycomb skeleton on the laser ablation damage on as-sprayed coatings was investigated by a comparative analysis of the laser damage morphology with different laser ablation times and gas flow. The results show that the honeycomb skeleton raises thermal conductivity and thermal diffusivity. Moreover, a “tower”-like dendrite was generated during the laser irradiation of the composite coating. The honeycomb skeleton refined the structure, suppressed crack propagation, and reduced the influence of gas flow on cracks. Under the same experimental laser ablation parameters, the laser damage area of the honeycomb skeleton-Al₂O₃ composite coating was smaller than that of the Al₂O₃ coating. It was demonstrated that the laser damage resistance of the honeycomb skeleton-Al₂O₃ composite coating was superior to that of the Al₂O₃ coating.     

Mechanical performance of ITO/Ag/ITO multilayer films deposited on glass substrate by RF and DC magnetron sputtering

ITO/Ag/ITO multilayer thin films have been a potential substitute of the conventional single-layer transparent conducting film. Nevertheless, the mechanical stability under preparation and in-service conditions still limits their applications and developments. In this paper, the influences of different structural properties as well as layer structure on both surface morphological properties and mechanical properties of the ITO/Ag/ITO multilayer thin films in comparison with commercial single-layer ITO thin film were systematically investigated. The results demonstrate that, i) the tri-layer composite has large impacts on the preferential orientation, and exhibits the decreased values of surface roughness, net lattice distortion and residual stress; ii) the increased hardness (H) and decreased Young's modulus (E) for full annealed ITO/Ag/ITO multilayer films indicate that it is possible to tailor mechanical properties of the materials by manufacturing multilayer composite; iii) the ITO/Ag/ITO multilayer thin film exhibits remarkable improvements in wear resistance with the increase of annealing temperature, which is mainly attributed to the increased ratios of H/E and H³/E².     

Effect of impact angle on wear behavior of Mo2NiB2–Ni cermets with different Ni content

Herein, the influence of the impact angle and Ni content on the wear behavior of Mo₂NiB₂–Ni cermets was studied using an erodent-carrying slurry comprising artificial seawater and SiO₂ sands. The results reveal that the material loss may be attributed to the wear damage caused by SiO₂ sands because cermets are expected to exhibit good corrosion resistance in artificial seawater. The relative density of cermets markedly influences their resistance to wear damage, and the material loss experienced by cermets with poor relative density is 2–4 times higher than that of cermets with good relative density; this occurs because a higher relative density can markedly enhance the mechanical properties and reduce the defects in the cermets. Moreover, the results indicate that as the impact angle increases from 0° to 60°, the manifestation of the wear mechanism changes from damaging the Ni binder phase (caused by single cutting wear) to damaging both the Mo₂NiB₂ ceramic and Ni binder phases due to the combination of cutting wear and impact wear. The wear damage is dominated by the cutting wear and impact wear from SiO₂ sand at the low and high impact angles, respectively. Furthermore, the severe deterioration of the single ceramic skeleton at high impact angles indicates that the synergistic influence of the Mo₂NiB₂ ceramic and Ni binder phases on enhancing the wear resistance of the cermets intensifies at high impact angles.     

Preparation and Characterization of Kenaf Papers Reinforced with Tapioca Starch: Physicomechanical and Morphological Properties

The present study reports the preparation and characterization of kenaf papers that reinforced with tapioca starch by using the ammonium zirconium (IV) carbonate as coupling agent. The examination shows the tearing resistance, tensile strength, and Young’s modulus of the kenaf papers are enhanced with the addition of starch and coupling agent, up to 3% and 1%, respectively. Under the optimum formulation, the degree of coupling reaction is 87%. The Fourier transform infrared and morphological analyses confirm the performance enhancement of kenaf papers is achieved via the formation of chemical bonding between the kenaf fiber and tapioca starch.     

C_4/C_5烯烃骨架异构化催化剂的制备及工业应用

采用水热晶化法合成了FER-S(加结构导向剂)和FER-01(不加结构导向剂)2种FER型ZSM-35分子筛,制备出C_4/C_5烯烃骨架异构化催化剂,利用X射线衍射法、氨气-程序升温脱附法等测试方法表征了分子筛结构,在固定床反应器装置上评价了催化剂异构化反应性能,并在中国石油乌鲁木齐石化公司40万t/a轻汽油醚化装置上考察了FER-S的工业应用情况。结果表明:FER-S,FER-01的结晶度分别为98%,83%,前者的强酸中心少于后者,且前者含有更多的微孔,催化剂性能更佳;FER-S在催化C_4和C_5烯烃异构化的反应中,正构烯烃转化率分别大于35%,45%,异构化选择性均高于90%;工业用FER-S在工业装置运行第1周期(769 h)内的72 h标定期间,C_5正构烯烃转化率达到62.4%～76.8%,异构化选择性高于90%,催化剂经过再生后,第2周期(1 053 h)的运行时间比第1周期至少延长37%。     

激励对往复式骨架油封密封性能的影响

为改善往复式骨架油封的泄漏问题,建立油封唇口密封区流体润滑的数值计算模型,模型考虑密封面粗糙形貌以及油封唇口的径向变形,通过求解雷诺方程分析密封区的流体力学特性,获得密封区的油膜厚度和压力分布,并分析激振频率和振幅对密封性能的影响规律。结果表明:随着激振频率的增加,内外行程中密封区的最小膜厚呈先增加后减小的变化趋势,激振频率越大,往复式骨架油封的密封性越差;内外行程中密封区的的最小膜厚随激振振幅的增加呈非线性增加,激振振幅越大,往复式骨架油封的密封性越好。综合考虑,为提高密封效果,往复式骨架油封适用于小频高幅的工作场合。     

Copy-move forgery detection of duplicated objects using accurate PCET moments and morphological operators

This paper presents a new method for copy-move forgery detection of duplicated objects. A bounding rectangle is drawn around the detected object to form a sub-image. Morphological operator is used to remove the unnecessary small objects. Highly accurate polar complex exponential transform moments are used as features for the detected objects. Euclidian distance and correlation coefficient between the feature vectors are calculated and used for searching the similar objects. A set of 20 forged images with duplicated objects is carefully selected from previously published works. Additional 80 non-forged images are edited by the authors and forged by duplicating different kinds of objects. Numerical simulation is performed where the results show that the proposed method successfully detect different kinds of duplicated objects. The proposed method is much faster than the previously existing methods. Also, it exhibits high robustness to various attacks such as additive white Gaussian noise, JPEG compression, rotation, and scaling.     

乙丙嵌段共聚物相对分子质量及链结构对PP/EPR共混体系结构与性能的影响

设计合成了一系列不同相对分子质量和乙烯平均序列长度的乙丙嵌段共聚物（EP），并将其作为聚丙烯（PP）/二元乙丙橡胶（EPR）共混体系的增容剂，考察了EP用量、相对分子质量及乙烯平均序列长度对共混体系性能及分散相形态演变的影响。结果表明，EP增容PP/EPR体系时存在最佳添加量，少量EP的加入可有效提高PP/EPR共混体系的抗冲击性能，并对分散相尺寸及形态起到良好的调控作用；同时，EP的相对分子质量越大对共混体系的冲击性能提高越明显，EP的组成与EPR越接近，对共混体系的增容效果越明显。     

A novel utilized method of tar derived from biomass gasification for fabricating binder-free all-solid-state hybrid supercapacitors

As an industrial pollutant, tar derived from biomass gasification is used as the precursor for fabricating a novel carbon-metal hydroxides composite electrode. A slurry (the mixture of tar, KOH and melamine) is daubed uniformly onto the nickel foam, which is directly carbonized to form NPC@LDH electrode material. This electrode is further coated with NiCo-LDH nanosheets using an electrodeposition method to form NF@NPC@LDH. The newly made NF@NPC@LDH electrode exhibits a high specific capacity of 9.6 F cm⁻² at a current density of 2 mA cm⁻² and good rate performance (55.3% retention). Furthermore, a hybrid NF@NPC@LDH//NF@PC all-solid-state supercapacitor is fabricated, and the device exhibits high energy density of 1.28 mWh cm⁻³ at a power density of 8.04 mW cm⁻³, low resistance and good cycling stability.