双螺旋结构电容式棒位测量传感器偏心性能研究

控制棒棒位测量传感器是低温核供热堆控制棒步进和落棒测量的关键设备，其精度和可靠性直接关系到反应堆的安全性。对于双螺旋结构电容式棒位测量传感器，完成了传感器静态特性实验，利用有限元分析方法建立了传感器的计算模型，模型计算结果与实验结果符合良好。在此基础上，采用有限元模型结合正交试验方法分析了极板张角、极板螺距、陶瓷管壁厚度等设计参数对传感器偏心性能的影响，获得了传感器设计参数的优化组合。研究结果表明，减小极板张角、增大极板螺距、增大陶瓷管壁厚度、减小陶瓷管相对介电常数有助于减小传感器偏心误差，由正交试验方法获得的参数组合能实现棒位测量不失步的要求。研究成果为双螺旋结构电容式棒位测量传感器的设计和优化奠定了基础。     

A novel multi-objective optimization method: Input values effect on responses (IVER)

In this study, a novel multi-objective optimization method based on the best effect of unique input (independent variable) values on responses (dependent variables) was proposed. The proposed method was compared with optimization using Derringer & Suich function that is still the most used. The comparison was made using the response values measured in real experiments and available in the literature. The advantages of the proposed method such as not needing the polynomial model aiming to predict the response values, no parameter selection problem, being able to offer optimum range instead of single optimum value, being suitable for use with existing experimental designs and being simple and interpretable were demonstrated as a result of comparison. It was also suggested how the proposed method will be effective according to experimental designs, and application for the users' application was presented.     

差分准对立学习多目标蚁狮算法

为解决多目标优化问题，对经典的蚁狮算法进行改进，提出了基于差分进化的准对立学习多目标蚁狮算法（DEQOMALO）。该算法针对蚁狮算法易陷入局部最优的不足，一方面，该算法引用差分进化的思想，充分利用种群和精英蚁狮的信息对原算法中蚂蚁个体的位置更新方式进行改进；另一方面采用反向学习策略对蚂蚁种群进行优化，将原种群个体和其准对立个体进行混合并择优作为新的种群，大大增加种群的多样性。选取典型的标准测试函数，将提出的算法与原始蚁狮算法以及其他传统进化策略优化的蚁狮算法进行比较。实验结果表明，改进算法在收敛性和分布性上均有很大程度的提升，在解决双目标优化问题上具有较好的鲁棒性和有效性。     

An improved iterative stochastic multi-objective acceptability analysis method for robust alternative selection in new product development

Alternative selection in new product development (NPD) is a multi-criteria decision-making (MCDM) problem. It usually starts with incomplete, imprecise or even partially missing information. Currently, most existing methods in dealing with this problem cannot work well if required information is incomplete or missing. It is acknowledged that stochastic multi-objective acceptability analysis (SMAA) can be applied to address MCDM problem with incomplete preference information and uncertain criteria measurements. In SMAA, alternatives are evaluated based on SMAA measurements (acceptability index, central weight vector and confidence factor). The discriminability of SMAA for the optimum alternative heavily depends on differences of SMAA measurements among different alternatives. Usually, a large number of alternatives and high level of uncertainty are involved in alternative selection in NPD. In this situation, the differences among SMAA measurements are not obvious, and therefore SMAA cannot deal with such problem very well. To this end, this paper proposes an improved SMAA method called Iterative-SMAA (I-SMAA) for alternative selection in NPD. In the I-SMAA, an iterative multi-step decision-making process is suggested to improve differences of SMAA measurements among different alternatives, and thus assist decision makers (DMs) to positively discern from the most preferred alternative. To enhance the decision-making efficiency, sensitive criteria are acquired in each iteration by ranking sensitivity analysis. DMs are guided to provide partial preference information and give more accurate criteria measurements for sensitive criteria rather than all criteria. Eventually, to verify the proposed method, a numerical example of the existing literature is solved with the method, and the results are compared. And then, a practical example of a preparation equipment for coal samples is further employed to verify the practicability of the proposed I-SMAA.     

Multi-objective optimal allocation strategy for the energy internet in Huangpu District,Guangzhou, China

To improve the overall efficiency of the energy system, the basic structure for the energy internet of coordination and optimization of “generation-grid-load-storage” of Huangpu District, Guangzhou, China is designed, while the arrangement for the output of centralized and distributed energy module and energy storage are proposed. Taking economic benefit maximization, environmental benefit maximization and energy efficiency maximization as sub-objectives, the mathematical model of multi-objective optimal allocation and operation strategy of the energy internet is established considering supply-demand balance constraints, equipment characteristic constraints, operation mode constraints, and energy conditions constraints. The calculation results show that without considering the outsourced electricity, the balanced strategy, the economic development strategy, the environmental protection strategy, and the energy efficiency strategy are obtained by calculation, which are all superior to the traditional energy supply strategy. Moreover, considering the outsourced electricity, the proportion of outsourced electricity to total electricity is 19.8%, which is the system optimization of the energy internet under certain power demand. Compared with other strategies without outsourced electricity, the outsourced electricity strategy can have a certain emission reduction effect, but at the same time reduce the economic benefit. Furthermore, the huge difference in demand for thermal and cooling load between industrial and commercial areas results in the installed capacity of gas distributed energy stations in industrial areas being nearly twice as large as that in commercial areas. The distributed photovoltaic power generation is allocated according to the proportion of the installed roof areas of photovoltaic power generation system in residential, industrial, and commercial areas.     

红外菲涅尔透镜的注射超声辅助成型优化

为了提升聚合物红外菲涅尔透镜的光学性能,以其表面微沟槽的成型质量为目标,提出了一种高效的注射超声辅助成型方法,并对工艺参数进行了综合质量优化。首先分析了超声振动对聚合物的加热和加压效应,设计了一套一模两腔的对比试验模具;接着以红外菲涅尔透镜的调制传递函数MTF和齿形平均高度h为优化质量目标,设计了四步骤的多目标优化流程,通过试验设计、基于BP神经网络的质量目标与注射工艺参数关系建模、基于NSGA-Ⅱ的多目标优化和试验验证进行工艺参数的综合优化。实验结果表明:该多目标优化流程具有很高的精度,MTF和h的平均预测误差MPE分别为4.16%和3.32%;注射超声辅助成型的菲涅尔透镜微沟槽具有更高的复制质量,其齿沟槽平均高度h增加了15.6%,且h值的波动量随着h值的增大而增大,MTF值受齿高h均匀性的影响大于齿高h对其的影响。     

基于深度学习的传感器优化布置方法

针对传感器优化布置(optimal sensor placement,简称OSP)问题,提出了一种新的使用深度神经网络的解决方案,并以简化的桥梁形状的桁架结构中的振动测试传感器优化为例进行了验证。首先,选择一种传统的传感器优化布置方法,对自动化生成的大量不同的桁架结构分别进行传感器优化布置计算,将所得优化布置结果在进行数据预处理后构建出深度学习方法所需要的训练集与验证集;其次,使用Python语言和深度学习框架TensorFlow设计实现与本研究问题适配的深度神经网络模型并训练;然后,随机生成了新的桁架结构参数;最后,将深度神经网络输出的传感器布置结果和传统方法的计算结果进行了比较,验证了本研究方法的有效性以及在速度上、可移植性与可扩展性方面的性能优势。     

绿色住区参数化优化设计平台的开发进展与展望

绿色住区设计是建设宜居城市和实现节能减排目标的重要手段与方法。文章首先回顾绿色住区参数化优化设计方法及平台概况，在此基础上，重点介绍平面生成、噪声计算、通风计算、可视度计算等新增功能和天空遮挡算法升级，以及广州市的工程应用，最后展望平台研发与应用的未来发展方向。     

基于变压器最优漏磁信息的绕组变形分类方法

为了判别电力变压器绕组变形状况,提出一种基于最优漏磁信息及多层聚类编码和最优权重译码的ECOC分类器对变压器绕组变形分类的方法,首先利用多层聚类算法构建最优ECOC编码矩阵,然后通过最优权重译码算法对分类器输出进行译码得出变压器绕组具体变形类别,建立变压器绕组二维漏磁场有限元模型,计算得出绕组可能出现的变形形式和绕组区域变形前后的磁感应强度值数据,从而得出磁感应强度测量点;最后利用所建立模型得出的绕组变形数据进行仿真判别。结果表明,所建立的分类器在绕组变形判别时具有较高的准确性,可用于变压器绕组变形类型的检测。     

[成形过程仿真优化与集成计算材料工程]限定加热管布局的快速热循环注塑成形模具电加热系统优化

针对管道布局、最大允许能耗给定条件下快速热循环注塑成形（RHCM）注塑模具型腔表面快速均匀加热的问题，提出以单根加热棒热流密度为设计变量，以模具型腔表面升温效率和温度分布均匀性为目标，结合有限元模拟、响应面设计以及多目标粒子群优化技术来优化RHCM模具电加热系统。与优化前相比，加热系统优化后，模具型腔表面最大温差降低63.4%，加热系统总能耗降低9%。对比了不同注塑成形工艺条件下成形的平板塑件表面质量，结果表明，相对传统注塑成形（CIM）工艺，RHCM工艺将制品表面粗糙度Ra从320 nm降低到118 nm，并有效抑制了制品表面熔接痕、缩痕等缺陷；发现制品表面粗糙度与型腔表面对应点温度成负相关，说明优化后的型腔表面温度分布更有利于提升制品表面质量。