微纳层叠聚丙烯腈凝胶流动特性的数值模拟研究

建立了层叠流道的三维模型和有限元网格模型，根据流变测试数据，采用Polymat对物料的黏度模型参数进行拟合，并利用Polyflow软件对聚丙烯腈（PAN）凝胶在层叠流道内的三维等温流动过程进行了数值模拟分析。研究发现，当入口流量增大时，层叠流道出口速度的不均匀性增加；沿流动方向流道内压力逐渐降低，并在出口处降低至同一最低值；流道进出口压力差与入口流量大小具有正相关性；在流道的中心截面上剪切速率分布均匀，波动较小。     

爆破位置对深凹露天矿山炮烟扩散的影响研究

深凹露天矿山由于其特殊的结构,爆破产生的炮烟扩散稀释较为困难,严重危害生产作业人员的生命安全与健康。基于实际矿山构建了深凹露天矿山的二维物理及数学模型,采用非稳态数值分析方法研究了不同爆破位置下,深凹露天矿山采坑内爆破炮烟的扩散规律。研究结果表明：不同爆破位置下,露天采坑内均出现复环流,爆破点位置是影响露天采坑内风流结构特征的重要因素；露天采坑内的炮烟最高浓度均随着时间变化而逐渐下降,但下降的速率逐步减小,呈现三个阶段的下降趋势；爆破位置位于背风侧时露天采坑内的炮烟最高浓度和降至安全浓度所需时间远高于迎风侧三个爆破位置；随着背风侧爆破点距采坑底部距离的减小,炮烟最高浓度及降至安全浓度所需时间先降低后增加,炮烟最高浓度及降至安全浓度所需时间随着迎风侧爆破位置距采坑底部距离的减小而增加。研究结果对于指导深凹露天矿山企业合理组织爆破后的生产作业和保障作业人员安全具有重要意义。     

地应力条件下的凿岩爆破数值模拟

为了研究地应力对凿岩爆破的影响,采用DDA方法模拟爆炸应力波作用下考虑地应力条件时的单孔和多孔凿岩爆破破岩过程。模拟发现,随着初始地应力水平的增加,裂纹扩展半径和破岩区域面积减小,裂纹发育主方向趋于地应力的最大主应力方向,初始地应力对裂纹的抑制和引导作用明显;初始地应力水平的增加,对拉伸裂纹的抑制作用更为显著,从而降低了拉伸破坏对爆破破岩的贡献。模拟也表明,在初始地应力存在的条件下,通过对爆破载荷和炮孔布置进行针对性的优化,可以克服地应力带来的影响,并取得预期的爆破效果。本研究对地应力条件下的凿岩爆破工程具有理论和参考意义。     

内含实体对H型垂直轴风力机气动性能的影响

以H型垂直轴风力机及其内含圆柱形实体为研究对象,对NACA0018翼型的五叶片H型垂直轴风力机的气动性能进行数值模拟和实验验证。分析8种不同直径的内含圆柱体,在内含实体截面积占风轮迎风面积之比分别为21.2%、50.0%和76.9%时,风力机风能利用率的峰值分别下降8.04%、20.7%及74.3%。结果表明：随着内含实体直径的增大,风能利用率的峰值逐渐减小,开始较为缓慢,达到一定值时快速下降。小直径内含实体主要影响叶片在下风区的转矩,对风能利用率的影响较小,而大直径内含实体还会影响叶片在上风区的转矩,其风能利用率迅速减小。对于内含固定直径的实体,比如在现有建筑物外侧安装风力机时,其风轮半径的选择需综合考虑风能利用率和风力机的建造成本两方面的因素。研究结果可为建筑物与垂直轴风力机进行有效结合以提高风能的利用提供参考。     

Combining a new baseboard radiator with a fan coil system for improving heating performance and reduce energy consumption

In the present work, the heating performance of a new system combined with a new modified baseboard radiator and fan coil is investigated. Using longitudinal fins with special geometry and also forced airflow at the end of the system causes that at the lower inlet water temperature compared with the conventional models, higher heat output rate be obtained. The heat output rate of the new modified system is obtained by experimental metrology based on the European Standard No. EN-442. Temperature and velocity distribution in the room space is done by simulation of the modified system in the Flovent software. Computational fluid dynamics (CFD) results are validated against experimental results and there is a good agreement between them. Also, the energy consumption of the system during the winter season is calculated in TRANSYS software. Experimental results show that the heat output rate of a new modified heating system with inlet water temperature in the range of 45–55°C is on average 4.17 times higher compared with the conventional model. CFD simulation also showed that the combined system provides good thermal comfort conditions. Energy consumption of the new system reduced about 13% compared with conventional models.     

Flow field simulation and pressure drop modeling by a porous medium in PEM fuel cells

For proton-exchange membrane fuel cells, the distribution of reactant flow in the stack is critical to the fuel cell's efficiency. The uneven distribution of reactant flow in the stack may cause poor current density, low performance, and material degradation. To understand and accurately predict the flow field in the proton-exchange membrane fuel cell system, the present study aims to develop a simple correlation to analyze the pressure drop in fuel cell stacks. The flow channel in each cell of a stack is treated as a porous medium, and a power-law model is used to approximate the porous medium momentum source term. For the stacks with fewer cell numbers, namely, 1, 5, and 10 cells, the parameters in the power law are established based on the experimental data. Then, a correlation is developed to simulate the flow and predict the pressure drop in the stack with higher cell numbers (ie, 20 and 40 cells). The simulations show that the pressure drop in each cell of a stack is almost invariable, and the average pressure drop decreases with increasing the number of cells. The flow uniformity in the stacks with different cell numbers is evaluated using the dimensionless pressure drop and the pressure drop ratios. It suggests that the lower the cell number, the more uniform the pressure drop. The developed model is conducive to efficiently designing the flow channel for a fuel cell stack with large cell numbers.     

基于CFD⁃DEM的水下切粒装置水室内颗粒流动过程数值模拟

基于CFD?DEM耦合方法，研究了颗粒在水室内的流动状态，分析了不同刀盘转速、粒子水通入量和水室出口角度对造粒过程的影响，发现提高刀盘转速、增加粒子水通入量和水室出口倾斜一定的角度都有利于水室内颗粒的排出。进一步研究了颗粒与碎屑在水室内的流动，发现在水室出口处二者的流动基本呈现出一定的分离角度。     

Squeezed MHD tangent hyperbolic fluid flow across a sensor surface

In the present numerical study, the combined effect of temperature-dependent thermal conductivity, linear thermal radiation, and magnetic effect on shear-thinning tangent hyperbolic fluid past a sensor surface has been studied. After converting the modelled partial differential equations into ordinary differential equations by using similarity transformation, the system of equations is tackled with the aid of the shooting method. The influence of important parameters on the fluid motion and energy distribution is displayed graphically and analyzed in detail. The presented simulations depict that a significant rise in fluid velocity is noticed for an enhancement in the magnetic parameter while an opposite trend is observed for the temperature distribution. Moreover, the skin friction coefficient decreases as the squeezed flow index is increased.     

媒体融合背景下高校学生记者队伍培养策略

媒体融合发展是高校开展新闻宣传工作的必然要求，针对高校学生记者队伍建设中存在的问题，提出要以“选修课+线上学习资源+校内培训”为抓手，学习相关专业学科知识；以学校融媒体中心为基础，为学生记者提供实践平台；深化学生记者对媒体融合传播理念的认识，不断提升互联网思维和创新能力。     

基于云网PoP的弹性边缘网络设计思路探讨

移动边缘云是公司“云+5G”双引擎战略的最佳契合点,边缘网络是发挥移动云“大云”产品和5G网络融合优势,实现云网统筹、构建运营商“连接+计算”核心能力的关键。运营商传统接入网存在云网割裂、分段入云和组网复杂等突出问题,难以适应边缘业务敏捷交付要求。本文通过深入分析边缘云业务特征和技术架构,对标业界主流云商建设实践,研究基于云网PoP网的边缘网络建设思路,创新性提出云网一体化规划设计和建设交付流程变革,基于云网POP统一网络和业务锚点,构建Overlay和Underlay融合双层加速网络架构,探索Spine-leaf化的新型城域接入网实现L3下沉和弹性扩容等方法,实现“云+网+应用”一体化敏捷交付的边缘网络能力。