基于双时间点检测的毫米波雷达人流量监测方法

针对现有基于视频监控的人流量统计方案成本高、算法复杂且不利于个人隐私保护的局限性，利用毫米波雷达体积小、成本低、分辨率高的特点，提出了一种基于双时间点检测的人流量监测方法。该方法先获取人体目标散射点位置和多普勒频移信息来构成点云数据，然后根据多普勒频移正负来判断人体的运动方向，并筛选具有高多普勒频移值的点云数据以降低干扰点对聚类结果的影响；在双时间点对特定区域内人员数量进行统计，并根据双时间点之间所获取的点云数据聚类结果对所统计人员数据进行修正。实验结果表明，该方法能够用匿名的方式以较高的正确率统计人员进出。     

High-performance Pb(Ni1/3Nb2/3)O3-PbZrO3-PbTiO3 ceramics with the triple point composition

Ternary 0.552Pb(Ni_1/3Nb_2/3)O₃-xPbZrO₃-(0.448-x)PbTiO₃ (PNN-PZ-PT) ceramics near the triple point compositions were fabricated by an improved two-step sintering method. The triple point composition 0.552PNN-0.135PZ-0.313PT ceramic has outstanding piezoelectric performance with piezoelectric coefficient d₃₃ = 1200 pC/N. Its easy fabrication and low cost make this piezoelectric material an excellent candidate for high sensitivity sensors and ultrasonic transducers. The evolution of domain structures for ceramics with composition near the triple point provides deeper insight into the mechanism of ultrahigh piezoelectric properties of PNN-PZ-PT ceramics.     

Effect of nanostructured grains in co-sputtered Ni-GDC thin-film anode on methane conversion kinetics for low temperature solid oxide fuel cells operating on nearly dry methane

Direct-methane solid oxide fuel cells (DMSOFCs) have recently attracted substantial attention due to their simplified system, reduced cost, and the direct availability of methane fuel obtained from natural gas. Among oxygen-ion conductive materials, doped-ceria such as gadolinium-doped ceria (GDC) or samarium-doped ceria can be incorporated into Ni-based anodes to reinforce their coking resistance, enlarge their electrochemical reaction area, and improve the kinetics of the internal reforming/electrochemical oxidation of methane. To reduce the range of operating temperatures of DMSOFCs while maintaining their performance, the thin film deposition technique of magnetron sputtering was adopted in this work. An Ni-GDC thin-film anode and a Pt thin-film cathode were deposited on scandia-stabilized zirconia (ScSZ) electrolyte supports. This fuel cell was tested with directly supplied methane fuel (3% H₂O) at 500 °C. The results demonstrated the effects of the GDC volume fraction in the anode—which was controlled by co-sputtering power—on open circuit voltage and electrochemical performance. The co-sputtered Ni-GDC anode was able to survive through 36-h operation, although there was some performance degradation. Field-emission scanning electron microscopy results revealed no formation of filamentous carbon on the Ni catalysts, despite the fact that both X-ray photoelectron spectroscopy and Raman spectroscopy analyses detected carbon coking. The relatively high performance and resistance to carbon coking of co-sputtered thin-film anode were attributed to its intrinsic small grain size.     

普通食用油检验关键点分析

以实际案例和文献资料收集为基础,主要围绕食用油检测从采样到结果判定一系列过程中可能涉及的操作风险点进行分析,并对部分典型检验指标(苯并(a)芘、塑化剂、抗氧化剂、残留溶剂、过氧化值、酸价、辣椒素、黄曲霉毒素B1)进行分析,介绍了分析过程中实验室环境、接触器具、试剂、样本本底、特殊基质干扰、指标稳定性等对实验结果有关键影响的因素,并针对具体问题提出解决措施,旨在为食用油检验风险防控提供技术支撑。     

车用有机朗肯循环系统中计量泵的性能研究

在模拟车用有机朗肯循环(organic Rankine cycle,ORC)系统的工作环境下,设计并搭建以R123作为工质的液压隔膜计量泵性能测试平台。在额定转速(2900 r/min)下,通过调节液压隔膜计量泵的冲程(25%、50%、75%、100%)和出口压力,得到变工况下液压隔膜计量泵的特性曲线,并分析液压隔膜计量泵的关键参数对车用ORC系统性能的影响情况。结果表明:液压隔膜计量泵的流量受冲程影响,与出口压力基本无关。其输入功率和实际运行效率均随着冲程的增加而升高,最高分别可达523.91 W、88.27%。应用该液压隔膜计量泵的模拟车用ORC系统吸热量变化范围较广,系统热效率最高可达12.81%。液压隔膜计量泵可应用于车用ORC系统,通过调节液压隔膜计量泵的冲程和出口压力,可实现提高车用ORC系统热效率、增加系统净输出功率的目的。     

薄膜铂电阻元件稳定性测试与分析

高端军事应用环境对测温传感器提出了小结构、高精度、良好的长期稳定性等要求,采用溅射方式制备的薄膜铂电阻元件成为了首选。通过分析薄膜铂电阻元件的结构、工艺,探讨影响稳定性的主要因素,包括薄膜缺陷、杂质、电迁移、结构封装应用与温度应力等。选择薄膜铂电阻在水三相点下的电阻值作为稳定性的比较基准,设计了一款不大于3mK的高精度测试系统。通过对薄膜铂电阻元件进行高温电寿命试验和温度冲击试验,评估得出薄膜铂电阻元件长期稳定性达到10mK,满足设计需求。     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

Analysis and assessment of a nanoparticle seeded small scale absorption refrigeration system driven by a low‐grade waste heat source

The thermoeconomic behaviour of a nanoparticle seeded single effect LiBr‐H₂O absorption refrigeration system (ARS) is investigated for a small scale application. In the proposed method, alumina nanoparticles with volume concentrations of 3%, 5%, and 7% are dispersed into an aqua lithium bromide solution. The multiobjective heat transfer search algorithm is employed to examine the design trade‐off between the coefficient of performance (COP) and total annualized cost (TAC). To analyze the overall performance of the system, the influence of five design parameters, namely the temperatures of the generator, absorber, evaporator, condenser and heat exchanger pipe diameter, are studied. It is found that with an increase in the COP, the TAC of the system is initially raised marginally, and after that, raised rigorously with further increment. The comparative results indicate that the COP and TAC of the nanofluid based ARS system are increased by about 7% and decreased by about 3.2%, respectively, corresponding to the Pareto points of the base ARS system. A lower break‐even point of about 2.6 years is achieved for the ARS system containing nanoparticles compared to the base ARS system. Overall, the ARS system containing 5% nanoparticles is the best solution from a thermodynamic and economic point of view.     

闭口闪点测定方法的对比分析

对我国常用的闭口闪点测定方法宾斯基-马丁闭口杯法、阿贝尔闭口杯法和泰格闭口杯法的测定原理进行对比分析，并采用这3种方法分别对2种有证标准样品、4种有机试剂样品和7种喷气燃料样品的闭口闪点进行测定。结果表明：这3种方法在适用范围、仪器结构、升温速率和点火操作要求等方面都有一定差异，导致采用这3种方法测定同一样品的闭口闪点结果略有差异，闪点测定结果之间的最大差值与样品闪点的高低呈正相关；与阿贝尔闭口杯法相比，宾斯基-马丁闭口杯法测得的闪点结果较高，对于3号喷气燃料，二者之差为0～1.0 ℃，阿贝尔闭口杯法更适合3号喷气燃料闭口闪点的测定；对于纯有机试剂样品，阿贝尔闭口杯法和宾斯基-马丁闭口杯法测得的闪点结果呈现较好的线性关系。     

Hybrid make-to-stock and make-to-order systems: a taxonomic review

Production planning and control (PPC) systems that employ aspects from both make-to-order (MTO) and make-to-stock (MTS) production control are known as hybrid MTS/MTO systems. While both MTO and MTS separately have been studied extensively, their combined use has received less attention. However, the literature on this topic is growing and this paper shows that the review performed in this paper is an important addition to the field. We categorise relevant literature according to a novel taxonomy and show that hybrid MTS/MTO production control can be used in different contexts. In addition, an overview of the modelling techniques and methods used in these papers is provided. Based on the reviewed literature, relevant research questions and directions for future research are identified. Finally, it is shown that hybrid MTS/MTO production control is prevalent in practice by discussing research with industrial applications. The paper contains an overview of research on hybrid MTS/MTO production control to be used as reference for researchers active in the field, and provides managerial insights and directions for future research on this topic.