Topology optimization of flexure hinges with a prescribed compliance matrix based on the adaptive spring model and stress constraint

This paper focuses on the configuration design of flexure hinges with a prescribed compliance matrix and preset rotational center position. A new method for the topology optimization of flexure hinges is proposed based on the adaptive spring model and stress constraint. The hinge optimization model is formulated by maximizing the bending displacement with a spring while optimizing the compliance matrix to a prescribed value. To avoid numerical instability, an artificial spring is used as an auxiliary calculation, and a new strategy is developed for adaptively adjusting the spring stiffness according to the prescribed compliance matrix. The maximum stress of flexure hinge is limited by using a normalized P-norm of the effective von Mises stress, and a position constraint of rotational center is proposed to predetermine the position of the rotational center. In addition, to reduce the error of the stress measurement, a simple but effective filtering method is presented to obtain a complete black-and-white design. Numerical examples are used to verify the proposed method. Topology results show that the obtained flexure hinges have the prescribed compliance matrix and preset rotational center position while also meeting the stress requirements.     

杂化包覆玄武岩鳞片/环氧涂料制备与性能

本文在环氧涂料中添加玄武岩鳞片，提高其防腐蚀性能。针对玄武岩鳞片的团聚问题，通过机械力化学改性工艺，采用正硅酸四乙酯、HY-311型钛酸酯偶联剂、E-44型环氧树脂对玄武岩鳞片进行杂化包覆，结果表明，杂化包覆后玄武岩鳞片的沉降时间从2h提高至96 h。杂化包覆玄武岩鳞片添加量为20%涂层的性能最优，附着力为13.40 MPa，耐盐雾时间为2000 h，在3.5%NaCl溶液中浸泡2000 h后，0.01 Hz的阻抗模值仍然有5.15×109 Ω·cm2。     

车门铰链系统与车门下沉刚度的相关性

针对某型车门下沉问题,通过台架试验获得车门、铰链和车身等各单因素下沉量和车门绞链系统整体下沉量,对单因素下沉量与系统整体下沉刚度进行线性拟合分析,得到车门铰链系统各单因素与系统下沉刚度的相关度排序.对前、后车门分别选取相关度较高的单因素进行优化,最终改进方案的仿真和试验结果证明该方案可有效地提升车门下沉刚度.采用定量分析法可快速找出影响下沉刚度的敏感因素,并能够快速生成优化方案,为新车型设计提供参考.     

电石汽车卸料、破碎、除尘、输送一体化智能系统——中吴天玺系统

针对PVC企业电石车间存在的粉尘污染严重、人工操作安全隐患大等问题,江苏中吴环境工程设计研究有限公司开发了电石汽车卸料、破碎、除尘、输送一体化智能系统(即中吴天玺系统),对该系统的工艺流程、系统组成、占地空间、经济效益和社会效益簣方面进行了介绍。     

Sustainable optimization of waste management network over extended planning time horizon

This study proposes a multiperiod mixed integer linear programming model for the management of a single municipal solid waste (MSW) treatment plant with sustainability as the objective. Discrete and continuous variables define the capacity selections for diverse MSW technologies, and the operation of the MSW network, respectively. The economic target is considered to maximize the net present value. The environmental impact is the minimization of a normalized environmental objective function (NEOF). The social target is the maximization of jobs. An interesting feature about the research work is the requirement of biodrying technologies for MSW moisture content control. Due to the conflicted nature among the sustainability components, a multiobjective optimization (MO) is carried out to find the Pareto optimal solutions. The MO results show that the Pareto optimal solutions vary around profit range of $4.9–8.5 billion, NEOF impact range of 3.2–3.6 units, and social benefit range of 2700–4828 jobs.     

An integrated dimensionality reduction and surrogate optimization approach for plant-wide chemical process operation

With liquefied natural gas becoming increasingly prevalent as a flexible source of energy, the design and optimization of industrial refrigeration cycles becomes even more important. In this article, we propose an integrated surrogate modeling and optimization framework to model and optimize the complex CryoMan Cascade refrigeration cycle. Dimensionality reduction techniques are used to reduce the large number of process decision variables which are subsequently supplied to an array of Gaussian processes, modeling both the process objective as well as feasibility constraints. Through iterative resampling of the rigorous model, this data-driven surrogate is continually refined and subsequently optimized. This approach was not only able to improve on the results of directly optimizing the process flow sheet but also located the set of optimal operating conditions in only 2 h as opposed to the original 3 weeks, facilitating its use in the operational optimization and enhanced process design of large-scale industrial chemical systems.     

基于PMU的电力系统监控体系结构优化设计

文中提出了一种利用有限数量的相量测量单元(PMU)和相量数据集中器(PDC)设计最优监控结构的方法。通过在大量的设定值场景下,使电力系统可观测性曲线的期望值最大化,同时使通信基础设施成本最小化,最终确定PMU和PDC的最佳位置。提出了一种非线性动态扩展卡尔曼滤波(EFK)状态观测器。这种状态观测器可以将暂态行为转换为由代数微分方程描述的广域电力系统,而无需非线性反演技术。最后以IEEE-5电力系统为例,说明了该方法的有效性。     

智能电网中D2D网络的通信资源管理优化方案

当前在智能电网的应用中,各种智能终端的使用,使得移动数据流量空前增长,电力互联方式在面临海量数据传输的需求时,由于资源受限,信道间会产生一定的干扰,从而影响通信质量。为了解决通信资源管理这一问题,与常见的移动边缘计算(MEC)方法不同,文中提出了一种网络资源分配方法,优化链路选择和子信道分配,以实现能量效率的最大化。仿真结果表明,与没有卸载和部分优化的方法相比,此方法在能效方面有了很大的提高。     

An optimal configuration for hybrid SOFC,gas turbine,and Proton Exchange Membrane Electrolyzer using a developed Aquila Optimizer

In this research, a technical, economic and environmental analysis has been proposed to a Hybrid Solid Oxide Fuel Cell (SOFC) system-based hybrid system including biomass, gas turbine, and Proton Exchange Membrane Electrolyzer. A multi-objective optimization technique has been utilized to improve the overall product cost and the exergy effectiveness based on a developed version of Aquila Optimizer (DAO). The main idea of using the developed version is to improve the accuracy and the precision of the original Aquila optimizer. The system is then authenticated in terms of energy/exergy effectiveness, and energy-economic efficiency. The achievements indicate that employing the optimization algorithm for different configurations provided satisfying results for the system.     

钢混结构大型厂房整体式爆破拆除

采用整体式控制爆破拆除方案对华电扬州电厂钢筋混凝土框-排架结构厂房进行了爆破拆除。爆破前,对汽机房、厂房外墙和楼梯进行了预处理。将厂房划分为3个爆区,采用非电多回路网格式爆破网路,依靠东侧锅炉房倒塌施加在西侧锅炉房上的倾覆力矩,有效地克服了西侧锅炉房向西倒的难题,可为同类工程提供一定的参考。