特种工程胎硫化外胎质量缺陷原因分析以及解决措施

我公司使用的硫化机采用氮气定型,二次水硫化的工艺。由于特种工程胎胎体偏厚且大,成型机都比较大,生产过程中的帘布筒、钢丝、胎侧等部件都比较重且大。成型胎面使用胎面缠绕机缠绕,所以整个生产过程难度较大。特种工程胎硫化外胎的主要质量问题有:胎面皮泡、胎侧缺胶、胎侧泡、胎肩侧皮泡、子口内侧露线、子口缺胶、胎肚内缺(窝气)、胎肚露线、胎肚皮泡、胎肚串泡、子口支边、胎冠支边、子口鼓包、外胎花缺等。通过对特种工程胎硫化外胎质量缺陷原因分析,找到相应的解决措施,从而减少硫化外胎质量缺陷。     

遗传算法优化的线性二次型调节器控制下3-UPS并联机器人稳定性分析

通过对3-UPS并联机器人进行动力学建模与状态空间分析,基于遗传算法(GA)优化的线性二次型调节器(LQR)控制方法对其进行控制仿真,结合多体系统振动理论,并运用MATLAB软件和ADAMS软件联合仿真,分别对该并联机器人在动平台施加外部载荷、定平台施加随机振动,以及动、定平台施加复合干扰3种情况下机器人的末端稳定性进行分析。结果表明:GA优化的LQR控制下,机器人动平台质心振动的衰减时间和振动幅度都明显减小,且共振峰也明显降低,但是高频振动处的减振效果不明显;机器人动平台质心x和y方向的共振频率均保持在5 Hz左右,而z方向的共振频率却有明显的后移现象,逐渐向高频(10 Hz)靠近。该研究为分析并联机器人稳定性与工作精度提供了一定的理论基础。     

食品中缩节胺形成机制研究进展

缩节胺是我国农业上普遍使用的一种植物生长调节剂,对棉花、番茄等农产品的生长、发育具有很好的促进能力。然而植物生长调节剂和其他农药一样,也存在某些毒性危害,但缩节胺的毒性和残留在我国并没有得到足够的重视。随着毒理学的发展,科研人员发现部分植物生长调节剂会有致癌作用。同时研究发现在特定的食品加工过程中,由于高温等操作会导致缩节胺的自然形成。食品中形成的缩节胺已成为影响食品安全的重要潜在因素,也吸引了人们对其危害的日益关注。本综述主要探讨了食品中缩节胺的形成机制,阐述参与缩节胺生成所需的甲基供体,总结其毒性研究,以期为缩节胺的控制奠定理论基础。     

IC塔沼气燃烧系统开车调试总结

通过参加伊朗造纸项目废水车间IC塔沼气燃烧系统开车调试总结,介绍了IC塔沼气燃烧系统主要设备及投料试车、控制联锁及调试期间注意事项等。     

云花皱织物的设计与开发

设计与开发了云花皱织物。络筒工序以"高车速、小张力、降毛羽、提产量"为工艺原则;整浆联合工序以"高车速、贴伏毛羽、减磨兼顾增强"为工艺原则;银丝不上浆,按照色经排列要求放在相应的伸缩筘中,并控制好张力;银丝和黑色花式线应穿在规定的综框;织造工序以"高车速、大张力、早开口"为工艺原则。经过对织造准备工序和织造工序的优化使得织造效率达到90%以上,下机一等品率达到93%,入库一等品率达到99%。     

Boost converter with adaptive reference tracking control for dimmable white LED drivers

An LED driver consisting of dimmable current regulators and a boost converter with adaptive reference tracking control (ARTC) is proposed. The ARTC is realized with only one integrator and one subtractor to detect the voltage variation among the current regulators and then to generate an adaptive reference tracking voltage. Based on the reference tracking voltage, the driving voltage of the boost converter is dynamically adjusted, so as to not only maintain a minimum voltage on the current regulator but also keep the required LED-string current. A prototype control circuit including ARTC and PWM control fabricated with TSMC 0.35-μm 2P4M CMOS process validates the proposed technique. The measurement results show that the driving voltage of the boost converter is automatically regulated to compensate for the voltage alteration on the current regulators. Furthermore, the overall efficiency of the LED driver with ARTC is 6.1% better than that of the LED driver without ARTC.     

Calculation of the Characteristics of Salient‐Pole Synchronous Machines Assisted by Permanent Magnets on the Basis of the Operating Principle

In this study we investigate a method for accurately calculating the characteristics of salient‐pole synchronous machines assisted by permanent magnets. First, the operating principle of the machines is investigated by using both finite element analysis and a simple magnetic circuit. Then, a theoretical representation of the assist effect on the permanent magnets is derived based on the magnetic circuit. Finally, the measured and calculated results are compared in order to confirm the validity of the proposed calculation method. We show that the load characteristics of the proposed machine can be accurately estimated from the no‐load and short‐circuit characteristics of the conventional machine without permanent magnets, and the size and magnetization of the inserted permanent magnets.     

High-temperature properties and interface evolution of silicon nitride fiber reinforced silica matrix wave-transparent composite materials

In order to improve the high-temperature performance of wave-transparent materials especially for the high-speed aircrafts application, filament winding combined with sol-gel method was adopted to the fabrication of unidirectional silicon nitride fiber reinforced silica matrix composites. The mechanical properties and the interface evolution at high temperatures were investigated. The results show that the composite sintered in N₂ maintains a flexural strength of 210MPa at up to 1200°C, while its counterpart prepared in air experiences a dramatic reduction to about 73MPa. The degradation is due to the partial oxidation of silicon nitride fibers at the fiber matrix interface. Besides, it is also notable that the bending strength of these two composites undergoes a similar growth from about 160 to 210MPa when tested under 900°C, which can be explained by the release of thermal stress on the silicon nitride fibers.     

喷涂缠绕保温管用全水发泡聚氨酯组合聚醚的研制

用聚醚多元醇A、聚醚二醇B、聚酯多元醇PS-2915、三乙醇胺、水和其他助剂制备了喷涂管道用全水发泡聚氨酯硬泡组合聚醚,并对其反应性能、黏度进行评价,对使用该组合聚醚和多异氰酸酯PM-200制得的聚氨酯泡沫材料的性能进行研究。结果表明,在合适的原料用量时,制得的组合聚醚黏度较低,与多异氰酸酯PM-200的反应速度满足喷涂管道生产工艺要求。当喷涂制得的聚氨酯泡沫单层厚度7 mm左右,泡沫体具有较高的粘接强度、较好的韧性和较低的导热系数,密度61 kg/m^3的泡沫压缩强度达到526 kPa。制得的喷涂管道产品满足GB/T 34611—2017要求。