宝浪油田宝北区块低渗透油藏层系优化研究

针对宝浪油田宝北区块低孔低渗油藏地质特征以及油层层数多、分布井段长、部分零散层动用难度大等问题 ,研究了宝北区有效厚度、油层层数、单井产能及单井控制地质储量等层系划分与组合的技术经济界限 ,并在此基础上进行了宝北区层系划分与组合优化论证 ,最终优选出宝北区开发层系     

声光效应拉曼-内斯方程矩阵级数解法及声光调制器优化设计

提出一种求解正常声光相互作用拉曼 内斯 (Raman Nath)方程的矩阵级数解法 ,该解法直观方便且具有普遍性。计算结果表明 ,对Q =4 1π ,Bragg衍射的效率只有 97 5 % ;对非对称入射 ,以往的Raman Nath近似解误差较大 ;指出提高Bragg衍射效率的有效途径在于提高声光频率比并给出计算声光器件最优长度的计算公式。     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

A time series bootstrap procedure for interpolation intervals

A sieve bootstrap procedure for constructing interpolation intervals for a general class of linear processes is proposed. This sieve bootstrap provides consistent estimators of the conditional distribution of the missing values, given the observed data. A Monte Carlo experiment is used to show the finite sample properties of the sieve bootstrap and finally, the performance of the proposed method is illustrated with a real data example.     

天津独流减河工程监控系统现地通信单元设计

提出一种配电网电容电流测量的新方法，在零序电压互感器的开口三角侧串联一个可调电感，通过注入一个变频恒流信号寻找配电网的谐振频率，改变可调电感的数值后寻找另一谐振频率，联立2个谐振方程求解电容电流，该方法消除了电压互感器漏抗对测量的影响。开发了配电网电容电流测量仪，经模拟试验和现场测试表明，该方法具有安全、快捷、准确等特点，适用于中性点不接地或经随调式消弧线圈接地配电网。     

基于复数主成分分析的磁共振波谱信号衰减系数的自动校正

衰减系数的校正是磁共振波谱信号处理和分析过程中的一个关键难题。本文基于复数主成分分析，提出了一种自动的磁共振波谱衰减系数的校正方法，较成功地解决了这个难点问题。文中的模拟数据及其实现结果充分验证了该方法的有效性。     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

Developing Cost Response Models for Company-Level Cost Flow Forecasting of Project-Based Corporations

The difficulty in applying the standard curve (S-curve) and cost-schedule integration (CSI) techniques for company-level cost flow forecasting in a project-based industry is the prerequisite of forecasting future unknown individual projects and contract classifications. By analyzing cost flows at the company level through a pool of macroeconomic and internal financial data, this paper proposes an innovative approach to firm-specific model estimation. First, a series of data transformations introduce linear relationships between cost, macroeconomic, and internal financial variables. Second, multivariate regression analysis is employed for initial model building. Third, for the purposes of model restructuring, a subsequent application of Yule–Walker estimates and incomplete principal component analysis is used. This paper uses a sample of four project-based construction firms to demonstrate model performance. Using this methodology, mean absolute percentage error (MAPE) values of the forecasting models range from 0.27 to 0.60%. As such, the transformed cost, macroeconomic, internal financial data could strongly predict company-level cost flow forecasting. While converting the predicted cumulative cost data to periodic cost flows, the MAPE values were augmented, ranging from 7.04 to 17.55%, thus, requiring future research.     

新型复合弹簧的研究

提出一种金属圆锥弹簧与橡胶圆锥弹簧复合而成的弹簧．分析表明：它可以应用于弹性耦合激励振动筛和座式直线振动筛。