Event-triggered variable horizon Supervisory Predictive control of hybrid power plants

The supervision of a hybrid power plant, including solar panels, a gas microturbine and a storage unit operating under varying solar power profiles is considered. The Economic Supervisory Predictive controller assigns the power references to the controlled subsystems of the hybrid cell using a financial criterion. A prediction of the renewable sources power is embedded into the supervisor. Results deteriorate when the solar power is unsteady, owing to the inaccuracy of the predictions for a long-range horizon of 10 s. The receding horizon is switched between an upper and a lower value according to the amplitude of the solar power trend. Theoretical results show the relevance of horizon switching, according to a tradeoff between performance and prediction accuracy. Experimental results, obtained in a Hardware In the Loop (HIL) framework, show the relevance of the variable horizon approach. Power amplifiers allow us to simulate virtual components, such as a gas microturbine, and to blend their powers with that of real devices (storage unit, real solar panels). In this case, fuel savings, reaching 15%, obtained under unsteady operating conditions lead to a better overall performance of the hybrid cell. The overall savings obtained in the experiments amount to 12%.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

探讨加强质量监督管理提高电网安全水平

电网的安全水平主要取决于其使用产品的质量是否过关。如果产品的质量较好，则能建造出优质的电网，电网的安全水平便会随之提高。因此，应加强对产品质量的监督管理，从而提高电网的安全水平。我们可建立质量监督管理系统，及时抽检出质量不过关的产品，从而消除电网运行过程中潜在的安全隐患。     

Third order optical nonlinearities characteristics of Disperse Red1 organic dye molecules inside of polymeric nanocapsules

Measuring nonlinear optical response of a specific material in a mixture, not only leads to investigate the behavior of a particular component in various circumstances, but also can be a way to select suitable combination and optimum concentration of additives and therefore obtaining the maximum nonlinear optical signals. In this work, by using dual-arm Z-scan technique, the nonlinear refractive index of Disperse Red1 (DR1) organic dye molecules inside the core of prepared polymeric nanocapsules was measured among various materials which prepared nanocapsules were made of them. Then the measured value was compared with nonlinear refractive index of DR1 solved in dichloromethane.     

The growth of oleaginous Rhodotorula glutinis in an internal-loop airlift bioreactor by using mixture substrates of rice straw hydrolysate and crude glycerol

The conversion of lignocellulosic biomass (LCB) to microbial oils is attracting a growing amount of attention. However, the growth of the oleaginous yeast Rhodotorula glutinis on LCB hydrolysate (mainly rice straw) only will lead to a low lipid mass fraction, in the range of 10–20%. This study shows that the addition of crude glycerol to the LCB hydrolysate medium can efficiently raise the lipid mass fraction to the range of 30–40%. Crude glycerol is a by-product in the biodiesel production process. The use of renewable LCB hydrolysate and crude glycerol would greatly reduce the substrate cost for microbial oil production using R. glutinis. In addition, the results of experiments show that a low-cost airlift bioreactor is a more suitable fermentation process for the growth of R. glutinis than the use of a conventional agitation tank. When using mixed carbon sources of LCB hydrolysate with 30 kg m⁻³ of reducing sugars and 30 kg m⁻³ of crude glycerol, a maximal cell mass of 21.4 kg m⁻³ and lipid mass fraction of 58.5 ± 6.2 were achieved in an internal loop airlift bioreactor, and this process may have the potential to be applied in scale-up production.     

Food recognition using neural network classifier and multiple hypotheses image segmentation

ABSTRACT

This paper proposes the multiple-hypotheses image segmentation and feed-forward neural network classifier for food recognition to improve the performance. Initially, the food or meal image is given as input. Then, the segmentation is applied to identify the regions, where a particular food item is located using salient region detection, multi-scale segmentation, and fast rejection. Then, the features of every food item are extracted by the global feature and local feature extraction. After the features are obtained, the classification is performed for each segmented region using a feed-forward neural network model. Finally, the calorie value is computed with the aid of (i) food volume and (ii) calorie and nutrition measure based on mass value. The experimental results and performance evaluation are validated. The outcome of the proposed method attains 0.947 for Macro Average Accuracy (MAA) and 0.959 for Standard Accuracy (SA), which provides better classification performance.     

土壤中石油污染物的脱附过程

文章中主要采用有机溶剂萃取法（OSE）对高浓度石油污染土壤进行修复，经过精馏操作，有效回收原油，建立脱附等温曲线，研究了石油污染物在土壤-有机溶剂两相间的迁移规律。     

离心泵并联运行工况点的数值求解

建立了求解多台不同型号离心泵并联运行工况点的数学模型,给出了用数值计算中的“二分法”求解该模型的方法,并附有用Exce l计算的实例。