Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Determinants of the intention to use non-medical insertable digital devices: The case of Chile and Colombia

In the past, thinking of carrying electronic devices inside our bodies was only posed by non-real scenarios. The emergence of insertable devices has changed this. Since this technology is still in its initial development stages, few studies have investigated factors that influence its acceptance. This paper analyzes the predictors of the intention to use non-medical insertable devices in two Latin American contexts. We used partial least squares structural equation modeling to examine whether six constructs predicted intention to use insertable devices. A questionnaire was administered to undergraduate students located in Colombia and Chile (n = 672). We also examined whether these predictors influenced intention differently for both of them. Four common constructs significantly and positively influenced both Chilean and Colombian respondents to use insertable devices (hedonic motivation, habit, performance expectancy, and social influence). Also, the habit has a complementary mediating effect on the relationship between social influence and behavioral intention. By contrast, effort expectations were a positive and significant predictor, but only among Chilean respondents. Findings suggest that when technologies are emerging, well-known predictors of intention (e.g., performance and effort expectations) are less influential than predictors related to self-efficacy (e.g., habit and hedonic motivation). The use of insertable devices has a significant impact on society. Thus, a better understanding of what motivates their use has implications for both academia and industry.     

Field-Effect Chiral Anomaly Devices with Dirac Semimetal

Charge-based field-effect transistors (FETs) greatly suffer from unavoidable carrier scattering and heat dissipation. Analogous to valley degree of freedom in semiconductors, chiral anomaly current in Weyl/Dirac semimetals is theoretically predicted to be nearly nondissipative over long distances, but still lacks experimental ways to efficiently control its transport. Here, field-effect chirality devices are demonstrated with Dirac semimetal PtSe₂, in which its Fermi level is close to the Dirac point in the conduction band owing to intrinsic defects. The chiral anomaly is further corroborated by the planar Hall effect and nonlocal valley transport measurement, which can also be effectively modulated by external fields, showing robust nonlocal valley transport with micrometer diffusion length. Similar to charge-based FETs, the chiral conductivity in PtSe₂ devices can be modulated by electrostatic gating with an ON/OFF ratio of more than 10³. Basic logic functions in the devices are also demonstrated with electric and magnetic fields as input signals.     

Orange to green switching anthraquinone-based electrochromic material

An easily accessible anthraquinone-benzodithiophene-based high bandgap polymer (PTAq) was synthesized by Stille coupling reactions in remarkably high yield (96.5%). The highest occupied molecular orbital energy level of the polymer was estimated from the onset of oxidation in a cyclic voltammetry study to be −5.7 eV. PTAq showed an orange-to-green color switching with the application of a 1.0-V external potential to the polymer film, which was visible to the naked eye. The optical behavior change was also monitored using ultraviolet–visible absorption spectroscopy and revealed a respectable 75% transmittance change when the polymer film was subjected to a 1.0-V external potential. The high color contrast observed makes PTAq one of the most promising materials for electrochromic device applications. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47729.     

A Complexing Agent to Enable a Wide-Temperature Range Bromine-Based Flow Battery for Stationary Energy Storage

Bromine-based flow batteries (Br-FBs) are considered one of the most promising energy storage systems due to their features of high energy density and low cost. However, they generally suffer from uncontrolled diffusion of corrosive bromine particularly at high temperatures. That is because the interaction between polybromide anions and the commonly used complexing agent (N–methyl–N–ethyl–pyrrolidinium bromide [MEP]) decreases with increasing temperatures, which causes serious self-discharge and capacity fade. Herein, a novel bromine complexing agent, 1–ethyl–2–methyl–pyridinium bromide (BCA), is introduced in Br-FBs to solve the above problems. It is proven that BCA can combine with polybromide anions very well even at a high temperature of 60 °C. Moreover, the BCA contributes to decreasing the electrochemical polarization of Br⁻/Br₂ couple, which in turn improves their power density. As a result, a zinc–bromine flow battery with BCA as the complexing agent can achieve a high energy efficiency of 84% at 40 mA cm⁻², even at high temperature of 60 °C and it can stably run for more than 400 cycles without obvious performance decay. This paper provides an effective complexing agent to enable a wide temperature range Br-FB.     

Effect of sintering conditions on structural and morphological properties of Y- and Co-doped BaZrO3 proton conductors

BaZrO₃-based materials doped with a trivalent cation have excellent chemical stability and relatively high proton conductivity which makes them potential proton conducting oxide materials for various electrochemical device applications such as hydrogen processing, high-temperature electrolysis, and solid electrolyte in fuel cells. However, BaZrO₃ showed poor sinterability, requiring high sintering temperatures (1700–2100 °C) with longtime sintering (20–100 h) to achieve the desired microstructure and grain growth. This sintering problem can be solved by slightly doping BaZrO₃ with a sintering aid element. Therefore, in this study, two different zirconate proton conductors: BaZr_0·9Y_0·1O_3-α (BZY) and BaZr_0·955Y_0·03Co_0·015O_3-α (BZYC) were sintered in an air atmosphere and an oxygen atmosphere for 20 h in the temperature range of 1500–1640 °C. The sinterability was evaluated by analyzing the XRD diffraction patterns, lattice constant, lattice strain, crystallite size, relative density, open porosity, closed porosity, surface morphology, grain size, and grain boundary distribution, using the XRD, SEM, EDX, and Archimedes density measurement methods. It is concluded that in an oxygen atmosphere, sintering aid Co not only improves the relative density but also produces highly dense fine particles with clear grain boundaries which are promising for electrochemical hydrogen device applications.     

孕妇可穿戴设备的应用与管理

近年来,孕妇可穿戴设备产业发展迅速,从胎心监护仪到多功能检查仪,实现了胎心、血糖、血压等指标的院内外监测与管理。孕妇可穿戴设备正以一种前所未有的方式将医院和母胎联系在一起。本文介绍可穿戴设备及其关键技术,探讨面向妊娠期女性可穿戴设备的典型应用及医院产科的监护管理模式,并分析当前国内外孕妇可穿戴设备领域面临的问题和对策。     

Reproducible,biocompatible medical materials from biologically derived polysaccharides: Processing and Characterization

Natural polysaccharides like chitosan and dextran have garnered considerable interest in biomedical applications due to their biocompatibility, biodegradability, and nontoxicity. Nonetheless, the development of a reproducible class of medical devices from these materials is challenging and has had limited success. Chitosan and dextran are inherently variable and synthesis using these materials is prone to inconsistencies. In this study, we put forward a robust product development regimen that allows these natural materials to be developed into a reproducible class of biomaterials. First, an array of validated characterization methods (Proton Nuclear Magnetic Resonance, titrations, Ultraviolet spectroscopy, Size Exclusion Chromatography—Multi-Angle Light Scattering, Size Exclusion Chromatography—Refractive Index, and proprietary methods) were developed that allowed rigorous specifications to be set for unprocessed chitosan and dextran, chitosan and dextran intermediates, and chemically modified materials—acrylated chitosan (aCHN) and oxidized dextran (oDEX). Second, a robust and reproducible synthesis scheme involving various in-process controls was developed to chemically modify the unprocessed polysaccharides. Third, purification methods to remove byproducts and low-molecular-weight impurities for both aCHN and oDEX were developed. The study presents a viable strategy for converting variable, natural materials into a reproducible class of biomaterials that can be applied in various biomedical applications. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48454.