冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

Voltage reference architectures for low-supply-voltage low-power applications

This paper presents a voltage reference generator architecture and two different realizations of it that have been fabricated within a standard 0.18 μm CMOS technology. The architecture takes the advantage of utilizing a sampled-data amplifier (SDA) to optimize the power consumption. The circuits achieve output voltages on the order of 190 mV with temperature coefficients of 43 ppm/°C and 52.5 ppm/°C over the temperature range of 0 to 120°C without any trimming with a 0.8 V single supply. The power consumptions of the circuits are less then 500 nW while occupying an area of 0.2 mm² and 0.08 mm², respectively.     

现场总线在冶炼烟气制酸系统中的应用实践

分析了冶炼烟气制酸工艺的特点，介绍了由PROFIBUS-DP现场总线构建的冶炼厂烟气制酸监控系统，详细介绍了其硬件配置及相应的软件设计。     

多带OFDM-UWB系统峰均功率比降低方法研究

针对多带OFDM—UWB信号存在高峰均功率比的问题，提出了利用扩展与交织降低系统信号峰均功率比的方法。该方法通过对传输数据进行正交扩展与交织，使得进入多载波调制的数据趋于高斯分布，减小了传输数据自相关函数的旁瓣峰值，降低了OFDM-UWB信号的峰均功率比。由于采用正交矩阵进行扩展，扩展前后的数据传输速率保持不变。仿真结果表明，扩展与交织可以有效地降低信号峰均功率比2-5dB左右。同时该方法还具有抗窄带干扰的鲁棒性。     

掺镱双包层高功率光纤激光器输出特性研究

对线形腔掺镱双包层高功率光纤激光器的输出特性进行了研究 ,通过求解速率方程 ,得到了激光器泵浦阈值功率、输出光功率和斜率效率的表达式。分析了光纤长度、腔镜反射率和泵浦波长等因素对激光器阈值功率、输出光功率和斜率效率的影响 ,为高功率光纤激光器的优化设计提供了理论依据