Superhydrophobic aluminum alloy surface with excellent universality,corrosion resistance,and antifouling performance prepared without prepolishing

It is urgently necessary to seek more simple and effective methods to construct superhydrophobic metal surfaces to improve the corrosion resistance and antifouling performance. Herein, a facile method for fabricating superhydrophobic aluminum alloy surface is developed via boiling water treatment and stearic acid modification. It is noteworthy that no prepolishing on aluminum alloy is required and no caustic reagents and typical equipments are used during the preparation procedure. Therefore, the fabrication method is quite a simple and environment-friendly technique. Both micro- and nano-scaled binary structure forms at the resultant aluminum alloy surface while long alkyl chains are grafted onto the rough aluminum alloy surface chemically. Consequently, the resultant aluminum alloy exhibits outstanding superhydrophobicity. More importantly, the superhydrophobicity has excellent universality, diversity, stability, excellent corrosion resistance, and antifouling performance. The facile preparation, excellent superhydrophobic durability, and outstanding performance are quite in favor of the practical application.     

氮含量及固溶温度对21-6-9奥氏体不锈钢组织和硬度的影响

为了探讨氮含量及固溶温度对21-6-9不锈钢组织和硬度的影响,分别在950、1000、1050和1100 ℃对3种不同氮含量的热轧态21-6-9不锈钢进行1 h固溶处理,通过光学显微镜观察其组织结构,结合Thermo-Calc热力学计算对试验钢的微观组织进行分析,并对其进行硬度测试。结果表明,0.20%~0.28%N的21-6-9不锈钢热轧后沿轧制方向析出铁素体,且钢中铁素体经950~1100 ℃固溶处理可消除,当N含量达到0.34%时,试验钢中不再出现铁素体。随着固溶处理温度的升高,21-6-9不锈钢的晶粒组织长大,硬度降低。N含量的增加可显著提高固溶态21-6-9不锈钢的硬度,其增加程度随固溶处理温度的升高而减弱。     

电子文件完整性检测系统的设计与实现

对电子文件完整性检查的方法进行了研究.电子文件完整性检查主要是关注某个文件是否被更改.利用信息摘要函数强有力的加密机制,识别文件发生的微小变化,只要是入侵者成功的攻击导致文件任何改变,都能被电子文件完整性检测系统发现,从而保证了对电子文件的完整性检查.文章介绍了CRC32、MD5、SHA-1算法的C语言实现.     

The influence of white mud on the water absorption,surface wettability,mechanical, and dynamic thermomechanical properties of core–shell structured wood-plastic composites

European Journal of Wood and Wood Products - To obtain the optimum balance between performance and cost, white mud (lime mud) was incorporated into the shell layer of core–shell structured...     

Low-Velocity Impact Damage Simulation of Biaxial Warp-Knitted Flexible Composite with Simplified Microstructure Model

Applied Composite Materials - In this paper, the low-velocity impact deformation behavior of biaxial warp-knitted flexible composite was investigated. A simplified finite element model (FEM) of the...     

Enhanced photoelectric properties of PbSnSe thin films via quick oxygen ion-implantation sensitization

Journal of Materials Science - Although chalcogenide materials continue to generate considerable interest due to great potentials for various optoelectronic devices, annealing for a long time in...     

Thermo-adjusted self-healing epoxy resins based on Diels–Alder dynamic chemical reaction

Micro-damage in materials could be repaired by endowing materials with self-healing performance. Herein, an epoxy resin with excellent self-healing performance grounded on thermo-reversible Diels–Alder dynamic chemical reaction was developed. Results showed that the bending strength and adhesive behavior of epoxy resin were influenced dramatically upon treatment with various temperatures. More importantly, damages created in epoxy resin could be repaired completely after suitable heat treatments. What is more, the healed epoxy resin exhibited much higher bending strength and adhesive performance than the pristine one did. The materials could be damaged and then repaired repeatedly. Meanwhile, the as-prepared self-healing epoxy resin exhibited excellent thermal reversibility and controllable adhesion. The thermo-adjusted self-healing performance endowed epoxy resin with recyclable and reusable performance. Therefore, the research made it possible of recycling waste epoxy resins.     

PTFE浓度对电厂冷却水管Ni-Mo-PPTFE复合镀层形貌和防垢性能的影响

采用单因素实验法研究PTFE浓度对电厂冷却水管常用的20#钢表面Ni-Mo-P/PTFE镀层的形貌和防垢性能的影响.结果表明,不同PTFE浓度下复合镀层的形貌特征既存在相似之处也存在差异.在5～20 mL/L的范围内随着PTFE浓度增加,复合镀层平整度提高,生垢速率减小,主要归因于复合镀层中PTFE质量分数逐渐升高.但当PTFE浓度超过20 mL/L,随着PTFE浓度继续增加,复合镀层平整度和防垢性能有所下降.PTFE浓度为20 mL/L时,该复合镀层表面较为平整,PTFE质量分数达到3.19％,具有相对较好的防垢性能.