Influence of temperature on acoustic emission source location accuracy in underground structure

An acoustic emission (AE) experiment was carried out to explore the AE location accuracy influenced by temperature. A hollow hemispherical specimen was used to simulate common underground structures. In the process of heating with the flame, the pulse signal of constant frequency was stimulated as an AE source. Then AE signals received by each sensor were collected and used for comparing localization accuracy at different temperatures. Results show that location errors of AE keep the same phenomenon in the early and middle heating stages. In the later stage of heating, location errors of AE increase sharply due to the appearance of cracks. This provides some beneficial suggestions on decreasing location errors of structural cracks caused by temperature and improves the ability of underground structure disaster prevention and control.     

基于改进SOA-VMD的磁声发射信号去噪算法

磁声发射（MAE）是铁磁性材料磁化过程中产生的声发射信号，在构件应力检测和微观损伤检测中有着广泛的应用。针对MAE信号非稳态、复杂性、衰减性等特点，提出海鸥算法结合变分模态分解（SOA-VMD）的去噪方法，为克服海鸥算法求解过程中易陷入局部最优解问题，利用柯西变异算子产生随机迭代过程，使改进算法即柯西变异海欧算法（CVSOA）跳出早熟收敛。采用以幅值谱熵为适应度函数，优化VMD算法中分解模态个数K和二次惩戒因子α两个参数，将含噪声的MAE信号进行VMD分解重构。经仿真信号和实际检测信号分析表明，改进后的CVSOA-VMD算法全局寻优能力和去噪性能优于传统的SOA-VMD算法，降噪后的MAE信号特征值对于不同应力下均方根、偏斜度特征值的重复性更好，可靠性更高。     

冰下单载波水声通信试验研究

北极地区战略地位的提高促进了极区各种应用的快速发展，冰下水声通信成为其中一个热点问题。为了研究冰下单载波水声通信性能，在黄海冰区开展冰下试验。重点分析了内嵌锁相环的多通道判决反馈均衡(Multi-channelDecision Feedback Equalization, M-DFE)技术在冰下水声通信中抗多途时延的能力，研究比较了改进比例归一化最小均方(Improved Proportional normalized Least Mean Square, IPNLMS)算法和递归最小二乘(Recursive Least Squares,RLS)算法的均衡性能。试验结果表明IPNLMS和RLS都能克服信道多途效应带来的影响。在牺牲计算复杂度的前提下，RLS具有更好的均衡效果，M-DFE在冰下环境中能够有效消除码间干扰。     

烯丙基聚烷氧基环氧醚的制备及其性能

针对烯丙基聚烷氧基环氧醚中存在催化剂和钾钠离子含量高,导致制备的三元共聚嵌段硅油反应活性差的问题,研究了在无相转移催化剂的条件下制备烯丙基聚烷氧基环氧醚的方法,表征了产物的结构,分析了制备条件对产物pH值与环氧指数的影响;以其为原料制备了三元共聚嵌段硅油,并对棉织物进行柔软整理,分析了整理后织物的亲水性、手感及物理力学性能。结果表明:当原料烯丙基聚氧乙烯醚、环氧氯丙烷和氢氧化钠的量比为1∶2.5∶1.5,冰醋酸的添加量是过量氢氧化钠的1.1倍时,产物烯丙基聚烷氧基环氧醚的环氧指数为1.77 mol/kg,pH值小于7,精制后钾钠离子含量可降低到5 μg/g以下;织物经过硅油整理后具有较好的亲水性,当整理液质量浓度为30 g/L时,毛效达到7.3 cm,手感评级达到4.7级以上,织物整体性能有所提高。     

Poly(4-styrenesulfonic acid) doped polypyrrole/tungsten oxide/reduced graphene oxide nanocomposite films based surface acoustic wave sensors for NO sensing behavior

Poly(4-styrenesulfonic acid) (PSSA) doped polypyrrole (PPy)/tungsten oxide (WO₃)/reduced graphene oxide (rGO) hybrid nanocomposite have been successfully synthesized using appropriate amounts of PSSA, pyrrole monomer, WO₃, and rGO dispersed in aqueous solution through in situ chemical oxidation polymerization. Here, a simple spin coating method was used to fabricate a nitric oxide (NO) gas sensor composed of the aforementioned nanocomposite on a surface acoustic wave (SAW) resonator. This sensor can detect NO gas at concentrations of 1–110 parts per billion (ppb) at room temperature in dry air, with a sensitivity of 12 Hz/ppb and response and recovery times of <2 min. Moreover, its limit of detection (LOD) is 0.31 ppb for a signal to noise ratio of 3. It demonstrates repeatability, fast response, and recovery at room temperature. Moreover, its sensory performance remains highly stable over 30 days with only a 6.3% decrease in sensitivity. In addition, the sensor is highly selective for NO, even when nitrogen dioxide, ammonia, and carbon dioxide are applied as interfering gases. The inclusion of rGO (with large specific surface area) and the synergic effect of n-type WO₃ nanoparticles in the p-type PPy matrix (leading to p-n heterojunction region formation) possibly underlie the efficient sensing performance of our sensor.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Study of SU-8 photoresist cross-linking process by atomic force acoustic microscopy

In this paper, a method is presented to detect the different phases of epoxy cross-linking process and the subsurface structures of SU-8 thin films by atomic force acoustic microscopy (AFAM). The AFAM imaging of SU-8 thin films was investigated under different exposure and bake conditions. Optimized conditions were obtained for the cross-linking of SU-8 thin film at the exposure does of eight laser pulses with the laser fluence 10 mJ cm^–2 per pulse and the post exposure bake (PEB) time at 90 s. The subsurface structures of undeveloped SU-8 thin films were visible in the AFAM images. This method provides an effective and low-cost way for the determination of different phases of epoxy cross-linking process in nanostructured compounds, for the non-destructive testing of subsurface defects, and for the evaluation of the quality of patterned structures.     

The Art of Masonry

Brick masonry is not only a question of building physics, building construction and durability, i.e. sustainability, but has much to do with aesthetics and making sense, which may have been forgotten in modern architecture with its absolute lack of décor. Masonry as an art form has been scarce since the era of brick expressionism. Recently, there have been some exceptions – and thoroughly welcome. The ”Fjordenhus“ in Vejle, Denmark, is an astonishing example.     

In‐plane shear damage behaviours of 2D needled C/SiC composites

Understanding the in‐plane shear behaviour of composites is essential to establish the design basis for practical applications. This study aims to investigate the shear damage behaviours of 2D needled C/SiC composites by various characterization techniques. The effect of layer arrangement on shear modulus and strength was discussed via shear stress‐strain responses. The shear strain field evolution and uniformity variation were studied by digital image correlation. It shows that the uniformity of shear strain field changes with the shear load, and the shear strain field evolution consist of 5 stages. The electrical resistivity measurement results indicate that structural deformation and damage evolution caused the electrical resistivity change. Furthermore, the damage evolution has a double effect on the electrical resistivity variation. The acoustic emission monitoring shows that the shear damage evolution is a 3‐stage nonlinear process before failure. The shear damages were categorized via acoustic characteristics. Besides, the postfailure behaviours were also discussed in this study.