Sulfate- and pH-driven metabolic flexibility in sugarcane vinasse dark fermentation stimulates biohydrogen evolution,sulfidogenesis or homoacetogenesis

Dark fermentation of sugarcane vinasse can be used as a “cleaning” step to remove sulfate prior to methanogenesis because sulfidogenic conditions can be successfully established in parallel with biohydrogen production. Using a 2² central composite rotational design (CCRD) and response surface methodology (RSM), this study assessed the impacts of bicarbonate and sulfate availability on the establishment of sulfidogenesis in the thermophilic (55 °C) fermentation of vinasse in batch reactors, equally assessing the impacts on biohydrogen evolution. CCRD-RSM results indicated the favoring of biohydrogen production at the lowest sulfate and bicarbonate concentrations, whilst the opposite was observed for sulfidogenesis. Glycerol, lactate, and hydrogen were the preferential electron donors utilized by sulfate-reducing bacteria (SRB), whilst ethanol was markedly consumed only at high sulfate concentrations. SRB were inhibited by sodium when dosing excess NaHCO₃ and Na₂SO₄. Complementary tests revealed maximum biohydrogen production (2.40 mmol) out of the CCRD, at pH exceeding 7.5 with no interference of sulfidogenesis. Non-efficient biohydrogen production was observed at low pH (<5.0; ～1.90 mmol) because the uptake of lactate was inhibited. Meanwhile, homoacetogenesis was established under intermediate pH range (5.5–6.5), as revealed by the accumulation of acetate (up to 2.5 g L^?1). 16S rRNA gene amplicon sequencing further revealed the genera Thermoanaerobacterium/Pseudoclostridium, Desulfotomaculum/Desulfohalotomaculum and Sporomusaceae/Moorella as the main biohydrogen-producing, sulfate-removing and biohydrogen-consuming (homoacetogens) microbial groups, respectively. Hence, using a single inoculum source, vinasse may provide a butyrate-rich (along with biohydrogen-rich biogas) or a sulfate-free and acetate-rich fermented effluent, depending mainly on proper pH control.     

Tunable BaxSr1-xTiO3 nanoparticles induced high energy storage density in layer-structured asymmetric polymer-based nanocomposites

In order to solve the problem of low charging and discharging energy density of dielectric capacitors, the structure design of layered polymer matrix composites is carried out in this paper. Ba_0.7Sr_0.3TiO₃, Ba_0.8Sr_0.2TiO₃ and Ba_0.9Sr_0.1TiO₃ nanoparticles were successfully prepared by the oxalate coprecipitation method. The surface of Ba_xSr_1-xTiO₃ was successfully coated with dopamine, which promoted the dispersion of the polymer matrix of the ceramic powder. Monolayer Ba_xSr_1-xTiO₃/PVDF composites containing Ba_xSr_1-xTiO₃ with different Ba/Sr ratios were successfully prepared by the casting method. Three-layer asymmetric composites with different fillers were successfully prepared by layer-by-layer casting. The phase and microstructure of the as-prepared materials were analyzed by XRD and SEM. The dielectric, electrical conductivity, ferroelectric and energy storage properties of the composites were tested. The effects and laws of the design of the three-layer asymmetric structure on the dielectric properties and energy storage properties of the layered composites are mainly studied. When the structure of the three-layer asymmetric composite is 1-2-3, the breakdown field strength reaches 330 kV/mm, the discharge energy density reaches 8.51 J/cm³, and the charge-discharge efficiency is 67%. This work demonstrates that layered composites with asymmetric properties can facilitate the development of electrical energy storage.     

毫米波三维异质异构集成技术的进展与应用

三维异质异构集成技术是实现电子信息系统向着微型化、高效能、高整合、低功耗及低成本方向发展的最重要方法,也是决定信息化平台中微电子和微纳系统领域未来发展的一项核心高技术。文章详细介绍了毫米波频段三维异质异构集成技术的优势、近年来的发展趋势以及面临的挑战。利用硅基MEMS 光敏复合薄膜多层布线工艺可实现异质芯片的低损耗互连,同时三维集成高性能封装滤波器、高辐射效率封装天线等无源元件,还能很好地处理布线间的电磁兼容和芯片间的屏蔽问题。最后介绍了一款新型毫米波三维异质异构集成雷达及其在远距离生命体征探测方面的应用。     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Stability assessment of 3D reinforced soil structures under steady unsaturated infiltration

Internal stability assessment of geosynthetic-reinforced soil structures (GRSSs) has been commonly carried out assuming plane-strain conditions and dry backfills. However, failures of GRSSs usually show three-dimensional (3D) features and occur under unsaturated conditions. A procedure based on the kinematic limit-analysis method is proposed herein to assess 3D effects and the role of steady unsaturated infiltration on the required geosynthetic strength for GRSSs. A suction stress-based framework is used to describe the soil stress behavior under steady unsaturated infiltration. Based on the principle of energy-work balance, the required geosynthetic strength is determined. A comparison analysis with the prior research is conducted to verify the developed method. Two kinds of backfills, i.e., high-quality backfill and marginal backfill, are considered for comparison in this work. It is shown that accounting for 3D effects and the role of unsaturated infiltration considerably reduces the required geosynthetic strength. The 3D effects are primarily affected by the width-to-height ratio of GRSSs, and the contribution of unsaturated infiltration is mainly influenced by the soil type, flow rate, GRSS's height, and location of the water table.     

MnS掺杂多孔碳复合材料的制备及电化学性能（两张发票1000+2500）

褐煤作为低级煤资源利用率不高，但褐煤中具有腐植酸成分，将褐煤中提取的腐植酸作为化肥原料，提取后剩余残渣作为碳源，与MnS纳米粒子制备了MnS@C复合材料。采用XRD、拉曼光谱、XPS、N2吸附-脱附、SEM和TEM对样品进行了表征。将该复合材料应用于锂离子电池负极材料，对其电化学性能进行了测试。结果表明，MnS@C复合材料的比表面积和孔容分别为117.19m2/g和0.044mL/g，该电极在0.1 A/g电流密度条件下循环200次后比容量高达830 mA‧h/g，且电极容量保持率为99%左右。在0.2、0.4、0.8、1.0、1.2和1.6 A/g电流密度下比容量分别为644、522、427、399、373和348mAh/g，展现出良好的倍率性能。MnS@C复合材料优异的电化学性能得益于碳基体的存在，不仅可以缓解MnS纳米粒子在嵌锂/脱锂过程中的体积膨胀，而且展示了锂离子电池高性能的巨大潜力，为褐煤的高值化利用作出巨大贡献。     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.     

Catalytic combustion synthesis of CNTs/MgO composite powders and the influences on the thermal shock resistance of low-carbon Al2O3–C refractories

Using MgC₂O₄, Mg powders as raw materials and Ni(NO₃)₂?6H₂O as a catalyst, CNTs/MgO composite powders were prepared by a catalytic combustion synthesis method. The CNTs/MgO composite powders were characterized by XRD, Raman spectroscopy, FESEM/EDS and HRTEM. The effects of catalyst content on the degree of graphitization and aspect ratio of the CNTs in composite powders were investigated. Moreover, the thermal shock resistance of low-carbon Al₂O₃–C refractories after adding the composite powder was investigated. The results indicated that the CNTs prepared with 1 wt% Ni(NO₃)₂?6H₂O addition had a higher degree of graphitization and aspect ratio. In particular, the aspect ratio could reach approximately 200. The growth mechanism of hollow bamboo-like CNTs in the composite powders was proven to be a V-L-S mechanism. The thermal shock resistance of Al₂O₃–C samples could be improved significantly after adding CNTs/MgO composite powders. In particular, compared with CM0, the residual strength ratio of Al₂O₃–C samples with added 2.5 wt% composite powders could be increased 63.9%.