Development of high pressure membraneless alkaline electrolyzer

A technology for cyclic generation of hydrogen and oxygen using electrodes made of variable valency material that does not need the use of separating ion-exchange membranes is presented. The technological solution enables to fabricate electrolyzers for uninterrupted producing high-pressure hydrogen with reduced energy intensity of the production. The total work for compressing 1 m³ of hydrogen and 0.5 m³ of oxygen has been estimated. Results of investigation of influence of discrete supply of DC current to the electrolysis cell, in order to improve the processes of gas evolution and to simplify the power systems of the electrolysis plant, have been considered. There is also considered an electrolysis installation equipped with a thermosorption compressor in which LaNi₅ is used as a hydride-forming compound. The comparative characteristics of the developed electrolyzer and the currently used hydrogen generators are given.     

Ablation behavior of thin-blade co-deposited C/Cx-SiCy composites under the influence of the complex fluid conditions of the oxyacetylene torch

This paper offers a new way of testing the ablation property of material under an oxyacetylene torch using a thin-blade specimen, which costs much less time to reach the maximum temperature and provides a harsh turbulence fluid field that's closer to reality. The thin-blade specimen experiences a higher turbulent intensity than the traditional disk-like specimen, leading to more efficient heat exchange. The fluid field simulation agrees with the testing results. In addition, we manage to synthesize the C/Cx-SiCy composites with the co-deposition chemical vapor infiltration (CVI) method. The C/Cx-SiCy composites exhibit a similar anti-ablation property as C/C composites and consist of enough SiC phase simultaneously, combining the advantages of both C/C composites and C/SiC composites. The thin-blade C/Cx-SiCy composites show a lower linear ablation rate (1.6 μm/s) than C/C composites (4.1 μm/s) and C/SiC composites (19.6 μm/s) during the oxyacetylene test. The glass layer formed on the surface of C/Cx-SiCy could cling to the bulk material instead of peeling off due to the high PyC content in the matrix could protect the SiO₂ from blowing away.     

基于压缩机-支架系统的异常噪声研究

针对某乘用车发动机转速在1 573 r/min，压缩机开启时车内噪声异常的问题，对样车进行试验分析与诊断，对压缩机-支架系统进行仿真分析，提出改进方案并验证改进效果。利用LMS声振信号采集系统采集振动噪声数据，采用频谱分析、阶次追踪等方法，并结合压缩机-支架系统模态仿真结果，确定车内异常噪声是压缩机轴频21阶与压缩机-支架系统3阶模态频率接近发生共振造成的。通过优化支架结构来提高压缩机-支架系统3阶模态频率以此来避免共振，并换装橡胶驱动盘缓和压缩机输入扭矩波动。将改进结构进行整车试验，结果表明：匀速工况空调开启时问题转速下，车内噪声降低了2.5 dB(A)；匀加速工况空调开启时发动机转速1 500~1 650 r/min区间，车内噪声无峰值，其余转速空调开启时改进前/后车内噪声基本不变，噪声波动趋势平缓。     

空压机润滑油系统可靠性试验研究

对空压机润滑系统进行分析,提出了一种润滑油压力调节机构,保证了空压机在高油温时油压正常,为空压机运动件提供充分润滑,从而提高空压机运行的可靠性。实验证明了该机构是可靠的,为空压机润滑系统设计提供了参考依据。     

CO压缩机优化运行总结

为确保原CO压缩机在净化系统升级改造项目实施后能安全稳定运行,采取了流程优化、工艺条件论证、设备缺陷排查、联锁指标重新确定等一系列措施。改造措施实施后,CO压缩机出口压力稳定在3.23 MPa左右,有效缓解了前后工序压力波动对压缩机稳定运行的影响,各级水冷却器的换热效果也得到了较大的改善。     

菌型叶根动叶片叶根叶冠内径向的加工

菌型叶根动叶片是一种新型的动叶片,采用数控铣加工叶根内径向面时留0.1~0.2mm余量,然后在进行叶根内径向磨削,叶冠直接加工到位,没有后序磨削加工,由于叶根叶冠在加工过程中不是一次装夹完成的,根冠存在一定的落差,在后续的装配中容易产生配合间隙,无法达到要求。文中介绍了一种新的加工工艺,解决了这一问题。     

航空发动机复杂扭曲叶片分步电解加工研究

为实现复杂扭曲叶片在较小间隙下的稳定加工,提出了一种分步式电解加工的工艺方法,建立了复杂扭曲叶片小间隙(0.2 mm)和大间隙下(0.5 mm)扭曲流道的流道模型,采用有限元法进行了流场仿真研究,结果表明增加流道间隙可以解决流道中涡流和流场紊乱的问题。开展了复杂扭曲叶片小间隙连续式加工和分步式加工的试验研究。结果表明,采用小间隙连续式加工,当阴极进给至3.8 mm位置时,在叶片排气边靠近叶根流道扭曲处出现短路打火情况;而采用分步式加工方式能够实现加工的顺利进行。     

基于儒可夫斯基变换的涡轮钻具叶片设计及性能分析

为提高涡轮钻具叶片使用性能和创新叶片设计理论,提出了基于儒可夫斯基保角变换法与经典水力翼型相结合的涡轮钻具叶片设计新方法,以?127涡轮钻具叶片为研究对象,运用搭建的涡轮钻具叶型参数化设计平台和自主设计的涡轮钻具性能测试台架,完成了5种翼型的造型设计,研究了5种叶片流场性能,开展了设计叶片的性能测试实验,对比分析了设计叶片与塔里木油田某型在役?127涡轮叶片的实际效能。实验及仿真结果表明,基于新方法设计的NACA-0012翼型加厚叶片在600 r/min转速及15 L/s流量的设计工况下,其单级扭矩达5.83 N·m,较相同条件下某在役?127涡轮的单级扭矩提高约6.4%,级效率提高约1.16%,整体性能有了实质提升。     

IBM PC集群计算机ATA磁盘系统升级技术方法研究

文章概述了IBMPC集群计算机的系统结构。对该系统在石油地震资料处理应用中存在的ATA磁盘系统故障率高的问题进行了分析，提出了针对刀片式服务器的ATA磁盘系统进行升级的解决方案。对石油地震资料处理高性能运算具有一定的参考价值。