异种铁素体耐热钢接头界面组织及其影响

综述了铁素体与铁素体异种金属焊缝（dissimilar metal welds，DMWs）接头界面组织及其影响。结果表明，在焊后热处理或运行温度下的铁素体钢DMWs接头的不均匀界面组织中，通常会形成脱碳层和增碳层。在铁素体钢DMWs焊接接头界面组织影响因素中，焊缝金属的化学成分有重要影响；焊后热处理规范（温度和时间）、工作温度下运行时间的影响较为突出；焊接工艺参数的影响亦不可忽略。异种钢接头界面处近缝区裂纹的产生，以及接头的蠕变强度随Larson Miller 参数增大而下降等不利影响，均为异种钢界面碳迁移行为所导致。焊缝成分控制法是接头界面组织控制或改善的必要条件，而脱碳层部位转移法能有效防止裂纹发生，亦是接头安全运行的重要工艺措施之一。     

Thermodynamic modeling of gas solubility in aqueous sodium chloride solution

An electrolyte Equation of State is presented by combining the Cubic Plus Association Equation of State,Mean Spherical Approximation and the Born equation.This new model uses experimental relative static permittivity,intend to predict well the activity coefficients of individual ions (ACI) and liquid densities of aqueous solutions.This new model is applied to model water + NaCl binary system and water + gas +NaCl ternary systems.The cation/anion-water interaction parameters of are obtained by fitting the exper-imental data of ACI,mean ionic activity coefficients (MIAC) and liquid densities of water + NaCl binary system.The cation/anion-gas interaction parameters are obtained by fitting the experimental data of gas solubilities in aqueous NaCl solutions.The modeling results show that this new model can correlate well with the phase equilibrium and volumetric properties.Without gas,predictions for ACI,MIAC,and liquid densities present relative average deviations of 1.3％,3.6％ and 1.4％ compared to experimental ref-erence values.For most gas-containing systems,predictions for gas solubilities present relative average deviations lower than 7.0％.Further,the contributions of ACI,and salting effects of NaCl on gases are ana-lyzed and discussed.     

Couple-based particle swarm optimization for short-term hydrothermal scheduling

A novel couple-based particle swarm optimization (CPSO) is presented in this paper, and applied to solve the short-term hydrothermal scheduling (STHS) problem. In CPSO, three improvements are proposed compared to the canonical particle swarm optimization, aimed at overcoming the premature convergence problem. Dynamic particle couples, a unique sub-group structure in maintaining population diversity, is adopted as the population topology, in which every two particles compose a particle couple randomly in each iteration. Based on this topology, an intersectional learning strategy using the partner learning information of last iteration is employed in every particle couple, which can automatically reveal useful history information and reduce the overly rapid evolution speed. Meanwhile, the coefficients of each particle in a particle couple are set as distinct so that the particle movement patterns can be described and controlled more precisely. In order to demonstrate the effectiveness of our proposed CPSO, the algorithm is firstly tested with four multimodal benchmark functions, and then applied to solve an engineering multimodal problem known as STHS, in which two typical test systems with four different cases are tested, and the results are compared with those of other evolutionary methods published in the literature.     

Mg-5Y-3Sm-0.8Ca-0.5Sb合金的高温蠕变行为

采用蠕变实验和理论计算,研究了时效态Mg-5Y-3Sm-0. 8Ca-0. 5Sb合金在250～300℃和50～70 Pa条件下的蠕变行为。结果表明,该合金具有良好的抗高温蠕变性能,其在300℃和70 MPa下的稳态蠕变速率为3. 28×10-8s-1。在50～70 MPa的应力下,当温度由250℃升到300℃时,应力指数由2. 30变为3. 22;在250～300℃的温度下,当应力由50 MPa升到70 MPa时,蠕变激活能由65. 4 kJ/mol变为81. 0 kJ/mol。     

A CCD-ADI method for two-dimensional linear and nonlinear hyperbolic telegraph equations with variable coefficients

In this paper, a combined compact finite difference method (CCD) together with alternating direction implicit (ADI) scheme is developed for two-dimensional linear and nonlinear hyperbolic telegraph equations with variable coefficients. The proposed CCD-ADI method is second-order accurate in time variable and sixth-order accurate in space variable. For the linear hyperbolic equation, the CCD-ADI method is shown to be unconditionally stable by using the Von Neumann stability analysis. Numerical results for both linear and nonlinear hyperbolic equations are presented to illustrate the high accuracy of the proposed method.     

基于双向流固耦合弹性环式挤压油膜阻尼器建模及动力学特性研究

利用数值方法建立了弹性环式挤压油膜阻尼器(ERSFD)的流固耦合模型,分别利用有限元方法以及有限体积法建立了弹性环和内外油膜的CFD数值模型,并进一步利用分时迭代的弱耦合方法实现了油膜以及弹性环控制方程的耦合求解,获得了内油膜的压力分布特性及弹性环的变形,并进一步识别了油膜和弹性环的动力学特性系数;研究了涡动频率、凸台数目、凸台高度、凸台宽度以及弹性环厚度对阻尼器动力学特性系数的影响。结果表明,弹性环的凸台高度对ERSFD油膜动力学特性系数的影响最为明显,ERSFD油膜阻尼与涡动频率无关。     

P91钢管道异常低硬度部位的组织和性能

对电厂运行过程中发现的P91钢主蒸汽管道的低硬度部位进行了微观组织观察、短时力学性能试验和高温持久强度试验,分析了其硬度偏低的原因。结果表明,低硬度区域P91钢组织为铁素体+析出物,位错密度较低,M₂₃C₆相在晶界处粗化聚集,同时析出新相Laves相,使得P91钢的短时力学性能和高温持久强度下降严重。     

热压烧结制备Cu/FeCoCr复合材料的显微组织及热物理性能

利用相图计算的CALPHAD方法和超音雾化制粉技术,在CuFeCoCr体系中设计并制备了一系列微米级复合粉体。通过热压烧结方法在烧结温度为950℃,烧结压力为45 MPa的工艺条件下成功获得块体复合材料。研究了块体复合材料中Cu含量对显微组织,热导率,热膨胀系数以及显微硬度的影响。结果表明:CuFeCoCr块体复合材料均由fcc富铜相和fcc富铁钴铬相组成。该系列复合材料经600℃时效处理8 h后,其热膨胀系数变化范围为5.83×10-6~10.61×10-6 K-1,热导率变化范围为42.17~107.53 W·m-1·K-1。其中Cu55(Fe0.37Cr0.09Co0.54)45复合材料表现出良好的综合性能,即其热膨胀系数和热导率分别为9.08×10-6K-1和91.09 W·m-1·K-1,与电子封装半导体材料的热膨胀系数相匹配。     

Short SiC fiber/Ti3SiC2 MAX phase composites: Fabrication and creep evaluation

The compressive creep of silicon carbide fiber reinforced Ti₃SiC₂ MAX phase with both fine and coarse microstructure was investigated in the temperature range of 1000-1300°C. Comparison of only steady-state creep was done to understand the response of fabricated composite materials toward creep deformation. It was demonstrated that the fibers are more effective in reducing the creep rates for the coarse microstructure by an increase in activation energy compared to the variant with a finer microstructure, being partly a result of the enhanced creep rates for the microstructure with larger grain size. Grain boundary sliding along with fiber fracture appears to be the main creep mechanism for most of the tested temperature range. However, there are indications for a changed creep mechanism for the fine microstructure for the lowest testing temperature. Local pores are formed to accommodate differences in strain related to creeping matrix and predominantly elastically deformed fibers during creep. Microstructural analysis was done on the material before and after creep to understand the deformation mechanics.