电网设备线夹开裂原因

某电力公司变电站用铝合金设备线夹在运行过程发生批次开裂事故,通过宏观观察、断口分析、化学成分分析、力学性能测试、冷冻模拟试验等方法,对设备线夹的开裂原因和开裂机理进行了分析。结果表明:设备线夹焊缝存在焊接缺陷,导致焊缝强度下降;设备线夹接线管底部存在积水空间,寒冷天气下积水结冰,体积膨胀,使焊缝承受设计工况外的负载而过载开裂,造成了线夹开裂。     

Water vapor volatilization and oxidation induced surface cracking of environmental barrier coating systems: A numerical approach

A numerical model is developed for surface crack propagation in brittle ceramic coatings, aiming at the intrinsic failure of rare-earth silicate environmental barrier coating systems (EBCs) under combustion conditions in advanced gas turbines. The main features of progressive degradation of EBCs in such conditions are captured, including selective silica vaporization in the top coat due to exposure to water vapor, diffusion path-dependent bond coat oxidation, as well as crack propagation during cyclic thermal loading. In light of these features, user-defined subroutines are implemented in finite element analysis, where surface crack growth is simulated by node separation. Numerical results are validated by existing experimental data, in terms of monosilicate layer thickening, thermal oxide growth, and fracture behaviors. The experimentally observed quasi-linear oxidation in the early stage is also elucidated. Furthermore, it is suggested that surface crack undergoes rapid propagation in the late stage of extended thermal cycling in water vapor and leads to catastrophic failure, driven by both thermal mismatch and oxide growth stresses. The latter is identified as the dominant mechanism of penetration. Based on detailed analyses of failure mechanisms, the optimization strategy of EBCs composition is proposed, balancing the trade-off between mechanical compliance and erosion resistance.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Inhibition of stress corrosion cracking in 304 stainless steel through titanium ion implantation

The effects of titanium ion implantation on the stress corrosion cracking (SCC) behaviour of 304 austenitic stainless steel were studied. Slow strain rate tests (SSRTs) were conducted on 304 steel in air and in 5?wt-% NaCl solution. The microscopic effects of ion implantation were evaluated by Stopping and Range of Ions in Matter Procedures (SRIM). Fracture morphologies and microstructures were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The fracture surfaces illustrate that ion implantation significantly inhibits the corrosion pits that initiate SCC. A dense passive film, which inhibits SCC, was formed during the ion implantation process. SCC initiation was restrained due to the dense dislocation nets that were generated by titanium ion implantation.

Highlights

• Ion implantation inhibits SCC susceptibility.

• The lack of Cr at the grain boundary leads to the expansion of SCC along the grain boundary.

• Implantation-induced damage leads to high-density dislocations.

• The surface was amorphised due to high-density dislocations.

     

β-环糊精修饰Ni/SFCC强化C9石油树脂催化加氢性能

以废弃的流化催化裂化催化剂（简称SFCC）为载体、β-环糊精为金属络合剂、硝酸镍为镍源，采用湿法浸渍法制备β-环糊精修饰的Ni/SFCC催化剂（简称Ni/SFCC-CD催化剂），考察其对C9石油树脂的催化加氢性能。通过BET比表面积测试、H2程序升温还原、X射线光电子能谱等手段对催化剂的物相结构进行表征，研究β-环糊精的作用机理及其对催化剂加氢性能的影响。研究结果表明：在反应温度为260 ℃、反应压力为7 MPa、反应时间为2.0 h的最优条件下，采用Ni/SFCC-CD催化C9石油树脂加氢，可制得溴值为1.45 gBr/（100 g）、色号（加纳德）小于1的水白色氢化C9石油树脂，催化剂循环使用4次后仍保持良好活性；β-环糊精的作用机理是：β-环糊精与硝酸镍产生络合作用，抑制硝酸镍的分解、控制NiO的结晶过程和增强活性组分Ni与载体之间的相互作用力，从而提高了Ni/SFCC-CD的催化活性和稳定性。     

Effect of cutting process on the stress corrosion susceptibility of AISI 304L stainless steel

During manufacturing of a component, cutting, turning, grinding, and milling operations are inevitable and these operations induce surface residual stresses. In this study, it is shown that, depending on the process employed for cutting, residual stresses generated at the cut surfaces can vary widely and they can, in turn, make the cut surfaces of austenitic stainless steel (SS) prone to stress corrosion cracking (SCC). An austenitic SS 304L plate was cut using three different procesess: bandsaw cutting, cutting using the cut-off wheel, and shearing. Surface residual stress measurement using the X-ray diffraction (XRD) technique is carried out close to the cutting edges and on the cross-section. SCC susceptibility studies were carried out as per ASTM G36 in 45% boiling magnesium chloride solution. Optical microscopic examination showed the presence of cracks, and confocal microscopy was used to measure the depth of cracks. The study confirmed that high tensile residual stresses present in the cut surfaces produced by cut-off wheel and shear cutting make the surfaces susceptible to SCC while the surfaces produced by bandsaw cutting are resistant to SCC. Hence, it is shown that there is a definite risk of SCC for product forms of austenitic SS with cut surfaces produced using cutting processes that generate high tensile residual stresses stored for a long period of time in a susceptible environment.     

某带钢连续热浸镀机组卧式连续退火炉水冷炉辊的开裂原因

采用宏观和微观形貌观察、化学成分分析、显微组织观察、硬度测试等方法,对某带钢连续热浸镀机组卧式连续退火炉水冷炉辊的开裂原因进行了分析。结果表明:水冷炉辊辊套成分中不含铌元素,镍元素含量偏低,导致组织中形成网状富铬碳化物析出相;辊套内腔结垢、水冷不畅使水冷炉辊产生局部过热,导致工作侧辊套基体中粒状合金碳化物的析出和网状富铬碳化物的长大,使工作侧辊套的脆性增加;随着结垢的沉积,水冷炉辊出现轴承转动不畅,甚至堵转现象;在热应力、扭力作用下,裂纹在网状富铬碳化物析出相中形成并沿网状碳化物逐渐向基体内扩展,最终导致水冷炉辊的开裂。     

Comprehensive study on hydrogen induced cracking of electrical resistance welded API X52 pipeline steel

Different heat treatment cycles were designed in order to investigate the effect of microstructural changes on hydrogen induced cracking resistance (HIC) and mechanical properties of the electric resistance welded steel. The heat treating of the as-welded specimen improved the ductility and impact toughness. After heat treatment, the uniform hardness profile was obtained for the welded specimens. The removal of local hard zones reduced the risk of HIC. The chemical composition and clustering of inclusions have a deleterious effect on cracking resistance in the H₂S environment. Aluminosilicate compounds and MnS inclusions were favorite sites for HIC. The most promising post weld heat treatment for improving mechanical properties and the resistance to HIC was the application of two-cycle quenching followed by tempering.