Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

Measurement of the tunnel rate in SIS' tunnel junctions as function of bias voltage

Cryogenic detectors with superconducting tunnel junctions can provide an energy resolution improved by at least one order of magnitude compared with standard semiconductor detectors. While the detection principle was already demonstrated many years ago, the past years were dedicated to the transition from the laboratory sample to practical detectors. Our most favored detector design gives rise to tunnel junctions with electrodes of unequal energy gaps. In such hetero tunnel junctions bias conditions can be established which cause a negative signal current. We report the experimental verification of this effect, and we discuss the yield of charge signal of cryogenic detectors based upon superconducting tunnel junctions.     

Paste Residence Time in a Spouted Bed Dryer. II: Effect of Spout Operational Conditions

Residence time distributions for an aqueous solution of 10% sodium chloride in a spouted bed dryer of inert particles were determined using the stimulus-response technique. Glass and polyethylene beads with diameters 2.6 and 3.4 mm were used as inert bodies in a cylindrical column of 14.0 cm diameter and 60° conical base. The effects of inert bodies load, air, and paste flow rates on the mean residence times and RTD were determined following 2³ factorial designs. The RTD could be correlated to the perfect mixing cell model with R² varying from 0.8684 to 0.9815. The mean residence times in CSBD varied from 10.8 to 13.9 and 10.7 to 13.3 min for glass and polyethylene beads, respectively. For both inert particles, mean residence times increased with bed height and decreased with paste feed rates. Also, terms of interaction among the factors were significant in some cases, showing a complex behavior of paste residence times. Equations obtained by response surface regression could predict mean residence times on glass and polyethylene beads with deviations lower than ±10%.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

A study of solid circulation rate in a circulating fluidized bed

An experimental investigation under cold condition was made to study the effects of some operating/design parameters and non-mechanical L valve configuration on the solid circulation rate in a 4.5 m tall, 0.15 m diameter circulating fluidized bed with riser flow rate varying from 1400 litres/min to 2000 litres/min and bed inventory from 15 kg to 25 kg of sand of average sizes 200 μm, 400 μm and 500 μm. Solid circulation rate was estimated by measuring velocity of sand particle travelling through a vertical Perspex tube section at the bottom of the return leg. It was found to be in the range of 2.8 to 12.3kg/m²s, 0.07 to 9.1kg/m²s and 0.12 to 2.23kg/m²s for sand sizes of 200 μm, 400 μm and 500 μm, respectively for a horizontal L valve. Two mathematical correlations have been developed from the experimental results to predict solid circulation rate as a function of riser flow rate, aeration flow rate, total bed inventory and particle size used.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Effect of additives on formation of natural gas hydrate

The formation of natural gas hydrate (NGH) is studied in this work. Kinetics data of hydrate formation with no agitation were collected at various concentrations of the aqueous solutions with different additives such as alkylpolyglucside, sodium dodecyl benzene sulfonate and potassium oxalate monohydrate. Various kinds of additive increased the formation rates of NGH and its storage capacity and reduced the induction time of NGH formation. Moreover, the storage capacity, the induction time and the hydrate formation rate were influenced by the concentration of the aqueous solution.