Comparative Analysis of Platelet-Derived Extracellular Vesicles Using Flow Cytometry and Nanoparticle Tracking Analysis

Growing interest in extracellular vesicles (EVs) has prompted the advancements of protocols for improved EV characterization. As a high-throughput, multi-parameter, and single particle technique, flow cytometry is widely used for EV characterization. The comparison of data on EV concentration, however, is hindered by the lack of standardization between different protocols and instruments. Here, we quantified EV counts of platelet-derived EVs, using two flow cytometers (Gallios and CytoFLEX LX) and nanoparticle tracking analysis (NTA). Phosphatidylserine-exposing EVs were identified by labelling with lactadherin (LA). Calibration with silica-based fluorescent beads showed detection limits of 300 nm and 150 nm for Gallios and CytoFLEX LX, respectively. Accordingly, CytoFLEX LX yielded 40-fold higher EV counts and 13-fold higher counts of LA⁺CD41⁺ EVs compared to Gallios. NTA in fluorescence mode (F-NTA) demonstrated that only 9.5% of all vesicles detected in scatter mode exposed phosphatidylserine, resulting in good agreement of LA⁺ EVs for CytoFLEX LX and F-NTA. Since certain functional characteristics, such as the exposure of pro-coagulant phosphatidylserine, are not equally displayed across the entire EV size range, our study highlights the necessity of indicating the size range of EVs detected with a given approach along with the EV concentration to support the comparability between different studies.     

工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Photo isomerization of cis-cyclooctene to trans-cyclooctene: Integration of a micro-flow reactor and separation by specific adsorption

Liquid-phase adsorption has hardly been established in micro-flow, although this constitutes an industrially vital method for product separation. A micro-flow UV-photo isomerization process converts cis-cyclooctene partly into trans-cyclooctene, leaving an isomeric mixture. Trans-cyclooctene adsorption and thus separation was achieved in a fixed-bed micro-flow reactor, packed with AgNO₃/SiO₂ powder, while the cis-isomer stays in the flow. The closed-loop recycling-flow has been presented as systemic approach to enrich the trans-cyclooctene from its cis-isomer. In-flow adsorption in recycling-mode has hardly been reported so that a full theoretical study has been conducted. This insight is used to evaluate three process design options to reach an optimum yield of trans-cyclooctene. These differ firstly in the variation of the individual residence times in the reactor and separator, the additional process option of refreshing the adsorption column under use, and the periodicity of the recycle flow.     

凌庄子水厂保水堰流量系数试验

凌庄子水厂蓄水池进水口处有一保水堰,为非标准薄壁堰,不能使用已有堰流公式对其过流量进行准确计算。为了得出较为精确的过流流量,按照重力相似准则制作几何比尺为1∶5的模型进行试验研究。在已有自由出流公式的基础上,对自由出流流量系数进行修正并对淹没情况下流量变化过程进行研究。对该非标准堰自由出流流量系数的实测值与经验值进行分析比较,发现堰板槽降低了实际自由出流过流能力。淹没出流的流量系数主要与下游尾水位有关,试验中形成的淹没式堰流受实际堰型尺寸影响,下游尾水位和堰上水位近似相等,不完全适用已有淹没出流流量公式,通过试验给出了修正淹没系数随h/p的变化关系。结果表明利用堰前、堰后水位初步计算过流流量是可行的,可为该工程提供参考,也可为实际工程中非标准矩形堰的流量计算提供思路。     

Simultaneously achieving high energy-storage density and power density under low electric fields in NBT-based ceramics

Aiming at the problem that power density and energy density are difficult to obtain simultaneously under low field, a novel composition (1-x)Na_0·5Bi_0·5TiO₃-xBaZn_1/3Ta_2/3O₃((1-x)NBT-xBZT) was designed and fabricated via solid-state methods. With the addition of BZT, the crystal lattice, structural symmetry, grain size, and dense degree were all increased proved by XRD, Raman, and Archimedes drainage method et al. Because of the enhancement of relaxor behavior, the x=0.10 sample displayed a high permittivity ε_r of 2871±15% and a low dielectric loss tan δ ≤ 0.025 in the wide temperature range of 60–400 ^oC. This ceramic also showed maximum recoverable energy density W_d (2.07 J/cm³) with high efficiency η (71.5%) under a low field of 150 kV/cm. Moreover, pulse discharge testing proved that this ceramic possessed both a significant discharge energy density W_D (0.96 J/cm³) and a record high power density P_D (108.54 MW/cm³). This work provided a promising material for high power and energy applications.     

5A06-O aluminium–magnesium alloy sheet warm hydroforming and optimization of process parameters

The uniaxial tensile test of the 5A06-O aluminium–magnesium (Al–Mg) alloy sheet was performed in the temperature range of 20–300 °C to obtain the true stress–true strain curves at different temperatures and strain rates. The constitutive model of 5A06-O Al–Mg alloy sheet with the temperature range from 150 to 300°C was established. Based on the test results, a unique finite element simulation platform for warm hydroforming of 5A06-O Al–Mg alloy was set up using the general finite element software MSC.Marc to simulate warm hydroforming of classic specimen, and a coupled thermo-mechanical finite element model for warm hydroforming of cylindrical cup was built up. Combined with the experiment, the influence of the temperature field distribution and loading conditions on the sheet formability was studied. The results show that the non-isothermal temperature distribution conditions can significantly improve the forming performance of the material. As the temperature increases, the impact of the punching speed on the forming becomes particularly obvious; the optimal values of the fluid pressure and blank holder force required for forming are reduced.     

Experimental investigation of supercapacitor based regenerative energy storage for a fuel cell vehicle equipped with an alternator

Recently, researchers have devoted more attention to supercapacitors (SCs) to integrate with batteries in energy storage systems (ESSs) for vehicle applications. In this study, we attempted to characterize the use of SCs in the ESS for a PEM fuel cell vehicle equipped with an alternator to maximize the performance of regenerative braking. We applied lithium-ion batteries (LIBs) and SCs as energy storage devices to examine their effect on ESS. Then we used a hysteresis brake to apply controllable braking force on the flywheel to form hybrid braking (HB) and made efforts to study its behavior to suggest a braking control strategy. We also ran the whole system over the rotational speed to cover the range of driving speed. At last, we sized the SCs for the most commonly used fuel cell electric vehicle (FCEV) in Korea, i.e., Hyundai NEXO, based on the results obtained from the above study by alternator efficiencies.     

Scaling analysis of hydrogen flow with carbon dioxide cushion gas in subsurface heterogeneous porous media

Subsurface hydrogen (H₂) storage in geological formations is of growing interest for decarbonization. However, there is a knowledge gap in understanding the multiphase flow involved in this process, which can have a significant impact on the recovery performance of H₂. Therefore, a full-compositional modeling study was conducted to analyze potential issues and to understand the fundamental hydrodynamic mechanisms of H₂ storage. We performed a range of 2D vertical simulations at the decametre scale with a very fine cell size (0.1 m) to observe the detailed flow behaviour of H₂ with carbon dioxide (CO₂) as cushion gas in various flow regimes. Issues such as viscous instability, capillary bypassing, gas trapping and gravity segregation are analysed here. To generalize our calculations, we have validated and applied the scaling theory in the context of subsurface H₂ storage. Since this study is focused on the hydrodynamic behaviour, three dimensionless groups, including aspect factor, capillary/viscous ratio and gravity/viscous ratio were identified to correlate recovery performance between various scales in a fixed heterogeneous system. It was found that H₂ could infiltrate the cushion gas in the proximity of the injectors, meaning that CO₂ is not displaced away from the injectors in a piston-like fashion. As a result, the purity of the back produced H₂ is much degraded, particularly in a viscous-dominated scenario. On the other hand, the injected H₂ mostly accumulates at the top forming a highly restricted mixing zone with CO₂ in the gravity-dominated case. The recovery performance is therefore much improved in this case. Although the gas distribution can be significantly altered by capillary forces leading to bypassed zones, the recovery performance of H₂ is hardly influenced. This is because the back-produced H₂ recovery is not dependent on the sweep efficiency of the gas. H₂ can be back produced following the same paths which were formed during injection.     

Novel branched sulfonated polyimide membrane with remarkable vanadium permeability resistance and proton selectivity for vanadium redox flow battery application

A series of novel branched sulfonated polyimide (bSPI-x) membranes with 8% branched degree are developed for application in vanadium redox flow battery (VRFB). The sulfonation degrees of bSPI-x membranes are precisely regulated for obtaining excellent comprehensive performance. Among all bSPI-x membranes, the bSPI-50 membrane shows strong vanadium permeability resistance, which is as 8 times as that of commercial Nafion 212 membrane. At the same time, the bSPI-50 membrane has remarkable proton selectivity, which is four times as high as that of Nafion 212 membrane. The bSPI-50 membrane possesses slower self-discharge speed than Nafion 212 membrane. Furthermore, the bSPI-50 membrane achieves stable VRFB efficiencies during 200-time charge-discharge cycles at 120–180 mA cm^?2. Simultaneously, the bSPI-50 membrane exhibits excellent capacity retention compared with Nafion 212 membrane. All results imply that the bSPI-50 membrane possesses good application prospect as a promising alternative separator of VRFB.     

电磁场与电磁波课程思政教学改革探索与实践

课程思政作为思想政治理论课程的有效补充，是落实立德树人根本任务的重要组成。《电磁场与电磁波》是物理、电类等专业的重要专业基础课程，深入挖掘其课程思政元素,能够发挥专业课程的隐性育人作用，实现知识传授、能力培养与价值引领的有机融合，对于理工科专业课进行课程思政改革具有现实指导作用。