基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。     

A Stimulation Method to Assess the Contractile Status of the Lumbar Extensors in a Seated Posture

The purpose of present study was to develop and evaluate methods to assess stimulation responses of the lumbar extensors, as part of a longer‐term goal of detecting fatigue during prolonged sitting. Three stimulation frequencies (2, 5, and 8 Hz) were tested in separate stages, which include 3 stimulation trains and 4 sampling blocks. Repeated measures analyses of variance were used to determine whether any significant differences in mean stimulation responses occurred with respect to stimulation frequency, sampling block, and stimulation train. Reliability of measured stimulation responses was assessed within and between sampling blocks using intraclass correlation coefficients. Stimulation frequencies significantly affected the stimulation responses and time‐to‐potentiation differed between the 3 stimulation frequencies; it was highest for 2 Hz stimulation. All 3 stimulation frequencies resulted in excellent reliability within and between sampling blocks. Use of the current protocol at 2 Hz is recommended as appropriate to measure the lumbar extensors status during prolonged sitting.     

基于射频技术的无刷同步电机励磁电流的检测

无刷同步电机的励磁系统对励磁电流的测量是制约该励磁方式发展的一大障碍。设计了一个射频系统可以用来解决同步电机的励磁电流的测量问题。该系统可以方便地检测到同步电机励磁机的整流二极管的工作状态并且可以动态地显示励磁电流，极大地方便了运行人员做出判断，而且结构简单、方便实用。     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。     

差分跳频通信系统的特点及性能

文章介绍了一种新型的短波跳频通信技术——差分跳频,分析了差分跳频技术区别于常规跳频技术的主要特点。针对按序列检测的信号接收方法,对差分跳频通信系统在AWGN信道下的性能进行了理论分析,同时做出相应的计算机仿真,证实了差分跳频通信技术和按序列检测方法的结合,使通信系统在AWGN信道下的性能得到了比较显著的提升。     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

移动机器人路径规划方法研究

移动机器人技术研究中的一个重要领域是路径规划技术，它分为基于模型的环境已知的全局路径规划和基于传感器的环境未知的局部路径规划。综述了移动机器人路径规划技术的发展现状指出了各种方法的优点与不足，最后对移动机器人路径规划技术的发展趋势进行了展望。     

小波变换在光谱特征提取方面的应用

人们在处理高光谱图像时一般要对一些典型地物进行光谱分析、特征波段的提取,以便提取出最大量的有效信息,剔除无用或冗余的信息,然后再进行分类识别.采用小波变换的分析方法,选用合适的小波进行分解,根据分解后的高频分量中包含的重要信息,利用局部相邻的正负极值点找出对应于原始光谱曲线上每个吸收带的左右边界;利用局部过零点,即可比较精确的提取出各个吸收带的中心波长.该方法比传统的光谱特征提取方法更简洁、有效,实验证明为一种比较理想的光谱特征提取方法.     

Accurate estimation of capacities and cross-traffic of all links in a path using ICMP timestamps

The estimation of the link capacity and its available bandwidth in an end-to-end path is crucial for network management, admission control and flow control for adaptive applications. This paper introduces an estimation mechanism able to accurately estimate the available bandwidth of all links in an end-to-end path, through its capacity and cross-traffic estimation. The estimation procedures resort to the dispersions of packet pairs and trains using the concepts of ICMP Timestamp and Traceroute that, efficiently used together, enable the measurement of the dispersions in all links in the path. These mechanisms were evaluated through simulation experiments, where we analyzed the influence of the several network parameters on each estimation mechanism. The results show that these estimation methods are able to accurately estimate both the capacity and the cross-traffic of all links in a path with moderate length and with low overhead.     

一种改进的MC-CDMA系统结构

MC-CDMA在频域扩频时实际上是一种频率分集,对于频率分集重数的要求通常小于子载波的数目N,故扩频因子可以小于子载波数目。改进了这种MC-CDMA系统的结构,通过在频域引入交织器,使交织后频率分集各分量经历独立的哀落,从而提高了抗哀落能力。最后给出了用系统仿真软件SPW仿真的结果。