Fabrication and properties of diatomite ceramics with hierarchical pores based on direct stereolithography

Porous diatomite ceramics with hierarchical pores and high apparent porosity (50.29–56%) were successfully fabricated via direct stereolithography. The pre-ball-milling time, dispersant type and dispersant concentration were systematically investigated to prepare diatomite pastes with high solid loading, low viscosity and a self-supporting effect. The results showed that a pre-ball-milling time of 24 h was more suitable to prepare diatomite pastes with high solid loading, and Span80 at 2 wt% was the optimal dispersant to obtain 40 vol% diatomite paste with a low viscosity and a self-supporting effect. To restrain the formation of defects, a heating rate as low as 0.2 °C/min was allowed to control the pyrolysis rate in the multistage debinding process. At sintering temperatures ranging from 900 °C to 1000 °C, porous diatomite ceramics exhibited a typical bimodal porosity, high apparent porosity and great flexural strength.     

Evaluation of a sulfidogenic system fed with microalgal biomass of Chlorella pyrenoidosa as an electron donor: Sulfate reduction kinetics

In this study, a sulfidogenic reactor fed with microalgal biomass of Chlorella pyrenoidosa as an electron donor was operated in a continuous mode. This study evaluated the influence of various initial sulfate concentration from 1.0 to 2.5 g/L on anaerobic sulfate reduction kinetics by a sulfidogenic enrichment culture predominantly Desulfovibrio sp. VSV2. It was observed that volumetric sulfate reduction rate (VSRR) was consistently increasing with an increase in volumetric sulfate loading rate (VSLR) across the retention time of 7–10 days. For a retention time of 7 days, the maximum VSRR was noted as 0.0050 g/(L.h) with a corresponding VSLR of 0.0089 g/(L.h). When retention time was maintained for 10 days, a maximum sulfate reduction of 65% and a maximum bacterial concentration of 1.632 g/L were achieved for an initial sulfate concentration of 1.5 g/L. It was concluded that VSLR facilitated through both dilution rate and initial sulfate concentration had a significant influence over sulfate reduction kinetics. The results of the study suggested that the microalgal-fed sulfidogenic system could be effectively employed for reduction of sulfate from sulfate-rich wastewater.     

Ferulic acid and EGCG alter the structural characteristics of ovalbumin and its application in mineral loading

This study aims to fabricate mineral-loading nanocarriers using natural materials. The interaction patterns between ovalbumin (OVA) and four water-soluble polyphenols, namely ferulic acid (FA), (-)-Epigallo-catechin 3-gallate (EGCG), gallic acid (GA) and epicatechin (EC), were investigated. Results showed that the optimised conditions for preparing stable OVA–polyphenol complexes are at the OVA–polyphenol ratio of 4:1 at pH 6, under which OVA–FA and OVA–EGCG showed the highest stability and mineral-loading capacity among four OVA–polyphenol complexes. The fluorescence results indicated that the addition of EGCG and FA induced a significant fluorescence quenching to OVA. The interaction between OVA and polyphenols involved hydrogen bonding, hydrophobic interaction and electrostatic interaction. Fourier transform infrared spectroscopy (FTIR) analysis suggested that both FA and EGCG enhanced the stability and orderliness of the structure of OVA. The transmission electron microscopy images also exhibited the spherical structure of OVA after the addition of FA and EGCG. Furthermore, scanning electron microscope–energy dispersive X-ray spectrum results suggested that OVA–FA and OVA–EGCG complexes were better mineral carriers than OVA–GA and OVA–EC. This study may serve as the theoretical support for the promising application of OVA in the fabrication of mineral-loading nanocarriers in functional food and pharmaceutic.     

Influence of density on the post-suffusion behavior of gap-graded sand with fines

Suffusion erosion, characterized as the selective detachment and transportation of finer particles by seepage flow, is hazardous to the stability and serviceability of geotechnical structures. The removal of finer particles deteriorates the structure and fabric of the soil, leading to the degradation of its mechanical properties. Studies into the effects of suffusion on mechanical behavior have so far produced disparate results depending on the pre-erosion relative density of the specimens tested. To investigate this issue, small cyclic and monotonic loading tests were performed on intact and eroded gap-graded silty sand specimens in three dispersed density states, using a triaxial cell modified for the purpose of erosion. The variation of Young's modulus showed an inverse relationship with the pre-erosion density of the specimen, as the small strain stiffness decreased in the dense cases and increased in the loose cases. Conversely, Poisson's ratio increased in value as suffusion progressed regardless of the initial density of the specimens. In the contractive phase of monotonic loading, the densification of the coarse soil skeleton by the downward seepage flow resulted in a decrease in contractiveness and an increase in secant stiffness. In the dilative phase, the increase in porosity by the erosion of finer particles reduced the dilatancy and peak strength of the specimens. The results suggest that the pre-suffusion density determines the primary locus of affected mechanical behavior in triaxial compression, which shifts from the contractive phase to the dilative phase with the increase in pre-suffusion density. The critical state strength, inferred using stress–dilatancy theory, was largely unaffected by the erosion of finer particles. As the results indicate, pre-erosion density may be of practical significance in assessing the vulnerability to deterioration and collapse of geotechnical formations and structures subjected to suffusion erosion.     

氮含量对HPD-1双相不锈钢组织及力学性能的影响

通过显微组织观察与力学性能测试研究了氮含量(0.08%~0.22％,质量分数)对HPD-1双相不锈钢硬度、拉伸性能、低温冲击性能及疲劳性能的影响。结果表明,氮含量变化可显著影响试验钢γ/α相比例,当氮含量由0.08％升高到0.22％,γ相含量由38.1％提高至56.5％。α相的硬度由273 HV10提高到343 HV10,γ相的硬度由238 HV10提高到299 HV10,试验钢强度明显提升。氮元素对两相比例和奥氏体相韧性的双重影响导致试验钢低温冲击性能呈先上升后下降的趋势;更高的氮含量抑制疲劳裂纹萌生与拓展,是影响HPD-1双相不锈钢室温疲劳性能的主要因素。撕裂棱是疲劳断口的显著特征。     

Free vibration behavior of a thermally post-buckled FG Timoshenko beam under large deflection using a tangent stiffness-based method

For thermally postbuckled configurations, the free vibration behavior of functionally graded (FG) Timoshenko beams are investigated. The postbuckling configurations are obtained through a geometrically nonlinear static problem. The free vibration problem around the postbuckled configuration is formulated using its tangent stiffness. The energy based governing equations are solved following the Ritz method. The elements of the tangent stiffness matrix are obtained using the Ritz coefficients. The results are shown to exhibit the effects of FG material, material profile parameter, and length-thickness ratio. The comparative results are presented for both the cases of the physical neutral surface and the geometrical neutral surface.     

Vertical cyclic loading response of geosynthetic-encased stone column in soft clay

Dynamic responses of the geosynthetic-encased stone column (GESC) supported embankment under traffic loads have become a hot topic. This study investigates the responses of GESC improved ground under vertical cyclic loading. A series of laboratory tests in a designed model test tank have been carried out with different loading parameters (varied loading amplitudes and frequencies), different column dimensions (varied encasement lengths and column diameters). In the tests, the soil-column stress distribution, accumulated settlement of loading plate, excess pore water pressure in the surrounding soil and lateral bulging of the stone column are monitored. Experimental results indicate that the vertical stress on the stone column increases with the increment of encasement length, and decreases with the increment of column diameter, loading amplitude and loading frequency. The increasing stress on the surrounding soil leads to a greater accumulated settlement of the loading plate and excess pore water pressure, while the increasing stress on the column leads to larger lateral bulging of the column. Excess pore water pressure dissipates effectively through vertical and horizontal drainage channels provided by the stone column and the sand bed. The geosynthetic encasement prevents the clay from obstructing the drainage channel by filtration and guarantees the drainage effect.     

Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters (such as the hole spacing L and the empty hole diameter D) and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η₁ and η₂ that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η₁ and η₂ can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.     

LTE室分高倒流小区解决方案的研究

LTE室分高倒流直接影响室内4G用户的感知，同时较大程度拉低LTE网络驻留率指标。由于室内无线环境的封闭性，室分小区之间的覆盖独立性，仅仅通过参数调整的手段达到降低高倒流的效果非常不明显，因此本文针对目前影响室内用户感知的高倒流问题，从高倒流小区的标准出发，对室分高倒流小区的发现手段，产生原因及解决方案进行详尽地阐述，并针对各类型的高倒流情形提出解决方法，最终提供读者发现、分析及解决室分高倒流小区的有效方案，从而作为研究方法提供给LTE室内小区高倒流问题解决的指导意见     

150单缸机试验台冷却系统流动与传热计算分析

基于Flowmaster软件建立了150单缸柴油机试验台冷却系统流动与传热模型,并在某大功率发动机上进行了验证。在此基础上分析得到了冷却水温度和流量、气缸套和气缸盖温度变化对冷却水总传热流量的影响规律,以及管道尺寸、壁面粗糙度、冷却水流量对冷却水流动总阻力的影响规律。