Novel organic dyes containing N-bridged oligothiophene coplanar cores for dye-sensitized solar cells

Three novel organic dyes adopting fully-fused coplanar heteroarene as the donor moieties end-capped with two cyanoacrylic acids as acceptors and anchoring groups have been synthesized, characterized, and used as the sensitizers for dye-sensitized solar cells (DSSCs). The photophysical and electrochemical properties of the novel dyes and the characteristics of the DSSCs based on the novel organic dyes were investigated. The incorporation of the coplanar cores with electron-donating N-bridges are beneficial for the better intramolecular charge transfer (ICT), giving these new dyes good light-harvesting capability. The LUMO energy levels of these coplanar heteroacene-based dyes are sufficiently high for the efficient electron injection to TiO₂ upon photo-excitation, while the suitable HOMOs allow the regeneration of oxidized dyes with the electrolyte redox (I⁻/I₃⁻). The structural features of the coplanar cores (penta vs. hexa heteroarene) as well as the alkyl substitutions play crucial roles in governing the physical properties and device performance. Among these three novel organic sensitizers, the EHTt dye composed of a fully fused hexa-arene core and less bulky N-alkyl groups caused the DSSC to show the best photovoltaic performance with an open-circuit voltage (V_OC) of 0.58 V, a short-circuit photocurrent density (J_SC) of 13.72 mA/cm², and a fill factor (FF) of 0.69, yielding an overall power conversion efficiency (PCE) of 5.52% under AM 1.5G solar irradiation.     

Use of the Retarded Solution-Reprecipitation Process to Attain a Higher Initial Permeability in MnZn Ferrites

We investigated the effect of various amounts of liquid phase on microstructure development during sintering and the resulting magnetic permeability of MnZn ferrite (MZF) samples. Our results revealed that the microstructure and the final magnetic permeability depend on the thickness of the liquid-phase film during sintering. The solution-reprecipitation (S-R) process, which is associated with an intensive microstructure development in MZF, starts when a continuous liquid-phase film of critical thickness δ_o, which wets the MZF grains, is formed. The solid-state sintering that takes place before the formation of the continuous liquid-phase film is essential for the final microstructure of MZF.     

软锰矿氧化硫化钡制高纯碳酸锰和氢氧化钡工艺研究

软锰矿同硫化钡溶液在较低温度下进行氧化还原反应，当硫化钡含量控制在26-75g／L范围内，软锰矿与硫化钡的物质的量比为2．5-3，反应时间50-60min，软锰矿被硫化钡还原为MnO，其还原率可达93．5％以上；还原后的锰用硫酸浸取，溶液经除杂后，与碳酸铵反应而制成高纯碳酸锰。硫化钡则被氧化为氢氧化钡，经蒸发、结晶而制得入水氢氧化钡，其回收利用率高速95％。     

Biodegradation of monoaromatic hydrocarbons in aquifer columns amended with hydrogen peroxide and nitrate

The ability of indigenous microorganisms to degrade benzene, toluene, ethylbenzene and xylenes (BTEX) in laboratory scale flow-through aquifer columns was tested separately with hydrogen peroxide (110 mg/l) and nitrate (330 mg/l as NO₃⁻) amendments to air-saturated influent nutrient solution. The continuous removal of individual components from all columns relative to the sterile controls provided evidence for biodegradation. In the presence of hydrogen peroxide, the indigeneous microorganisms degraded benzene and toluene (> 95%), meta- plus para-xylene (80%) and ortho-xylene (70%). Nitrate addition resulted in 90% removal of toluene and 25% removal of ortho-xylene. However, benzene, ethylbenzene, meta- and para-xylene concentrations were not significantly reduced after 42 days of operation. Following this experiment, low dissolved oxygen (< 1 mg/l) conditions were initiated with the nitrate-amended column influent in order to mimic contaminated groundwater conditions distal from a nutrient injection well. Toluene continued to be effectively degraded (> 90%), and more than 25% of the benzene, 40% of the ethylbenzene, 50% of the meta- plus para-xylenes and 60% of the ortho-xylene were removed after several months of operation.     

SO2转化温度异常情况分析

结合凤山实业总公司硫酸车间 SO2 转化系统的具体工艺流程 ,分析近几年转化系统出现温度不正常的原因 ,提出解决方法     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

添加剂对尖晶石型锰酸锂性质表征的影响

以LiOH·H_20和MnO_2为原料,分别掺入H_2BO_3、Al_2O_3、SiO_2和P_2O_5等添加剂,用固相分段法制备尖晶石型锰酸锂。结果表明,SiO_2和P_2O_5可以有效地改善LiMn_2O_4的电化学性能,H_3BO_3对锰酸锂的电化学性能影响不大,而Al_2O_3破坏了LiMn_2O_4的电化学性能。面扫描结果显示,Si或P元素各自都均匀地分散于LiMn_2O_4的物相中。从元素电负性和原子半径的角度分析了B、Si、P和Al元素对尖晶石型LiMn_2O_4结构和性能的影响。     

锂离子电池正极材料锂锰氧化物的固相合成研究进展

阐述了固相合成反应的原理，综述了锂锰氧化物的几种固相合成方法，并着重介绍了熔融渍法，多步加热法，机械化学法和微波化学法等在锂锰氧化物合成中的研究进展。     

理学SMX-10/11型X荧光光谱仪的改进

对理学SMX-10／ll型X荧光光谱仪真空系统、样品定位系统及热交换器冷却水循环路径等易发生故障部位进行改进，并在11型仪器上增加了S元素分析通道。生产应用表明，改进效果良好，简化了分析工艺。降低了分析成本，提高了仪器的稳定性。     

动力配煤高温复合固硫剂研究

分析了高温复合固硫剂各成分的作用，实验研究了在不同配比的燃烧试验下，各成分对燃煤着火和燃烧以及对炉渣固硫的影响，得出了该煤种高温复合固硫剂的最佳配方。