Fatigue life improvement of 12Cr1МoV steel by irradiation with Zr+ ion beam

Cyclic tension and bend tests were performed on heat-resistant 12Cr1MoV steel specimens in as-supplied condition as well as after Zr⁺ ion beam surface irradiation. Distinct differences in strain induced relief, as well in cracking pattern of modified surface layer were observed by optical microscopy and interference profilometry. Changes in subsurface layer are characterized by means of nano- and microindentation and fractography of fracture surfaces (with the help of scanning electron microscopy). It is shown that the main influence on mechanical properties is mostly induced by thermal treatment during irradiation rather than formation of a 2 μm thick layer doped with Zr. The differences in deformation behavior may be explained by physical mesomechanics concepts.     

Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。     

游梁式抽油机间歇供电装置的研制与应用

针对游梁抽油机电动机效率低和井场窃电问题,研制了具有节电和防井场窃电功能的游梁抽油机调压+间歇供电装置。该装置通过控制可控硅的导通角实现在电动机做功期调压供电,在电动机发电期不供电。分析了间歇供电对电动机、抽油机和电网的影响;根据现场实测数据分析了该装置的节电效果及现场应用情况。该装置节电效果显著,能防止井场窃电,可用于对游梁抽油机电动机的长期驱动。     

自动交换光网络控制平面功能结构的探讨

文章主要讨论了自动交换光网络(ASON)控制平面的两种不同结构：控制平面在网元外部的结构和控制平面部分集成在网元内部的结构，并对这两种结构进行了比较．     

An Acoustic Converter Used to Measure Ionizing Radiation Energy Loss

A monitor is proposed based on ultrasonic production when ionizing radiation passes through a medium. The recording element is a 0.2 mm aluminum plate mounted in a ceramic acoustic converter AC in the form of a wedge of thickness 2 mm. The low plate thickness minimizes the beam parameter distortion, while special technology used in the AC provides high sensitivity. The device has been calibrated in the proton beam from the ITEP accelerator at 200 MeV with 2·10⁹–6·10¹⁰ particles in a pulse and a pulse length of 70 nsec.     

天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。     

MPID─TOF质谱的快速时间分辨微弱信号测试系统

把瞬态记录仪Ｂｉｏｍａｔｉｏｎ８ｌ００与微型计算机ＩＢＭ─ｐＣ／ＸＴ联接建成了一个高速数据采集系统，本文介绍了系统的硬件接口设计及软件设计。在超声分子束条件下，把它应用于环氧乙烷（Ｃ＿２Ｈ＿４Ｏ）的多光子电离与离解飞行时间（ＭＰＩＤ─ＴＯＦ）质谱的实验研究中，并给出了实验结果；本系统在微观基元化学反应动力学实验研究中广泛适用于对时间分辨微弱信号的探测。     

局部设有钢筋砼电梯井墙的设计探讨

本文就局部设有钢筋砼电梯井的工程计算及理论分析，阐明分析了少墙的框剪结构的设计及注意问题。