Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

数字电视用中分辨率74cm纯平彩色显像管BC配列不良的分析与对策

通过对74cm中分辨率纯平彩色显像管BC配列局部严重群散不良的调查分析,确定荫罩受力塌陷是主要原因,通过改良设计、工艺优化及其它方面的综合对策,使以上技术难题得到满意的解决,整管不良率由4.78%下降到0.172%。     

Selective area epitaxy of CdTe

We have performed selective area epitaxy (SAE) of CdTe layers grown by molecular beam epitaxy using a shadow mask technique. This technique was chosen over other SAE techniques due to its simplicity and its compatibility with multiple SAE patterning steps. Features as small as 50 microns × 50 microns were obtained with sharp, abrupt side walls and flat mesa tops. Separations between mesas as small as 20 microns were also obtained. Shadowing effects due to the finite thickness of the mask were reduced by placing the CdTe source in a near normal incidence position. Intimate contact between the mask and the substrate was essential in order to achieve good pattern definition.     

荫罩黑化及DX气与煤气成分的探讨

本文介绍了彩色显像管荫罩黑化反应的机理,详细说明了DX气制气流程,以及DX气的成分对黑化膜品质的影响。计算分析了成分不同的煤气在制成DX气时的成分变化。同时还分析了黑化工艺和黑化设备对煤气成分波动的适应性,及在生产实践中改变DX气制气时的煤气空气对黑化膜质量的影响。     

Optical analysis of crack tip stress fields: a comparative study

Four optical techniques for evaluating stress intensity factors in opaque specimens are described in outline, and compared for both an artificial crack and a fatigue crack. The results are compared to a standard solution for the geometry considered. All the techniques gave acceptable results over a range of stress levels and crack lengths. The methods of caustics and strain gauges were less good, whilst photoelasticity gave consistent results over a wide range of stress levels. Comments on the ease of application and the resource implications are also made in order to assist practitioners.     

局部阴影下光伏阵列MPPT算法的研究

针对局部阴影状态下光伏阵列P-U特性曲线多峰值的问题,提出了一种基于搜索-计算-判断的三步法全局最大功率点跟踪(GMPPT)策略。该方法使用改进型扰动观察法反向搜索第一个峰值点,利用计算和判断减小搜索区域,将多峰值间接转化为单峰值搜索,解决了搜索过程中陷入局部极值的问题。通过建立3种阴影状态下的模型,将该方法与现有最大功率点跟踪(MPPT)算法进行仿真对比,并建立相应的试验进行验证。仿真及试验结果表明,该方法在有、无阴影状态下均能稳定实现GMPPT,有效地提高了系统的跟踪精度和跟踪速度。     

数字皮影动画脚本的研究与应用

为简化数字皮影动画的制作流程,提高数字皮影作品的交互性,降低数字皮影实时表演的难度,对皮影常见角色及动作进行了抽象、分类,提出一种针对特定类型的通用的骨骼模型。基于反向动力学,设计了一套描述皮影骨骼动画的脚本。该脚本通过对骨骼位置与旋转属性的控制定义皮影角色的基本动作,并通过对基本动作的叠加实现复杂动作。脚本对动作的定义基于骨骼模型而非具体角色,具有通用性。最后通过实验证明了脚本的有效性。     

皮影电脑动画解析

为实现皮影电脑动画的再现,从剧本选择进行解析,提出武打戏中的动态表现美;从动画软件运用上阐明了二维电脑动画软件是表现皮影动画的最佳选择;在画面分镜头设计中,强调动画镜头艺术表现力是提升皮影电脑动画艺术感染力的重要手段．经过分析得出,电脑动画在表现皮影戏艺术方面有着独到的优势．