A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

岩石物理横波速度曲线计算技术

横波速度是地震勘探中的重要参数。针对实际生产中缺乏横波速度测井曲线资料，利用经验公式计算精确度不高的问题，通过对横波速度计算理论模型的研究分析，选择Blot-Gassman模型法，利用岩石矿物成分、流体成分、孔隙度及密度等测井曲线进行横波速度测井曲线的计算，并对横波速度计算技术和流程进行研究。在实际工区进行了横波速度曲线计算，计算结果与实测横波吻合程度较高，误差小于10％，该技术在储层和流体识别预测的应用中取得了较好效果。     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。     

Conductive Mechanism of Organic Conductor

Organic conductor is a kind of organic compound which has special electronic and magnetic properties. The research of the organic compounds has received considerable attention because of their potential applications in many areas. The molecular conductive units are theoretically investigated as well as their energy gap and charge distribution. The relationship of conductivity and micro-mechanism is discussed.     

低潮时期宽带网建设需要注意的问题

宽带建设低潮期实际上是一次优胜劣汰的过程,宽带运营竞争的手段将由低价竞争转向服务质量和特色的竞争。应在重视宽带接入建设的同时,也要重视业务运营管理平台的建设。应从长远考虑,不应仅为了节省投资而降低对设备的要求。由于降低成本的主要方向是在线缆部分,因此EVDSL技术应用的速度将大大超过人们的预期。在网络建设上,IPDSLAM虽有优势但也有不足,还需要进一步的成熟、稳定和实践的检验。     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

The mechanics of compressive kinking in unidirectional fiber reinforced ductile matrix composites

Three distinct stages of kink band formation and propagation exist in ductile matrix composites subjected to compressive loading. These stages are called incipient kinking, transient kinking and kink band broadening. Each stage involves a different deformation mode. The mechanics governing each stage are discussed. Incipient kinking, where the peak load is attained, and kink band broadening, where the load attains a steady-state, are important in structural design. Two design philosophies are presented. References to pertinent literature are made throughout.     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

L波段窄脉宽500W固态功放组件的设计

介绍了作者研制的应用于固态雷达发射机上的L波段500W固态功放组件的工作原理、用途及其主要技术指标。描述了功放组件的设计过程和测试结果。该功放组件在窄脉宽条件下实现了快速上升沿,性能优良,工作稳定可靠。