地应力条件下的凿岩爆破数值模拟

为了研究地应力对凿岩爆破的影响,采用DDA方法模拟爆炸应力波作用下考虑地应力条件时的单孔和多孔凿岩爆破破岩过程。模拟发现,随着初始地应力水平的增加,裂纹扩展半径和破岩区域面积减小,裂纹发育主方向趋于地应力的最大主应力方向,初始地应力对裂纹的抑制和引导作用明显;初始地应力水平的增加,对拉伸裂纹的抑制作用更为显著,从而降低了拉伸破坏对爆破破岩的贡献。模拟也表明,在初始地应力存在的条件下,通过对爆破载荷和炮孔布置进行针对性的优化,可以克服地应力带来的影响,并取得预期的爆破效果。本研究对地应力条件下的凿岩爆破工程具有理论和参考意义。     

Strength and deformation properties of frozen sand under a true triaxial stress condition

In recent years, the mechanical properties of frozen soils under complex stress states have attracted significant attention; however, limited by the test apparatus, true triaxial tests on frozen soils have rarely been conducted. To study the strength and deformation properties of frozen sand under a true triaxial stress state, a novel frozen soil testing system, i.e., a true triaxial apparatus, was developed. The apparatus is mainly composed of a temperature control system, a servo host system, a hydraulic servo loading system, and a digital control system. Several true triaxial tests were conducted at a constant minor principal stress (σ₃) and constant intermediate principal stress ratio (b) to study the effect of intermediate principal stress (σ₂) on the mechanical properties of frozen sand. The test results showed that the stress–strain curve can be mainly divided into three stages, with evidence of strain hardening characteristics. The strength, elastic modulus, and friction angle increased with the increase in b from 0 to 0.6, but decreased when increasing b from 0.6 to 1, whereas the cohesion varied little with the variation in b. The deformation in the direction of σ₂ changed from dilative to compressive and that in the direction of σ₃ remained dilative throughout.     

Direct shear behavior of gravel-rubber mixtures: Discrete element modeling and microscopic investigations

In this paper, a newly developed 3-dimentional discrete element model (DEM) for gravel-rubber mixtures (GRMs), namely DEM4GRM, that is capable of accurately describing the macro-scale shear response (from small to large deformation) of GRMs in a direct shear box apparatus is presented. Rigid gravel grains are modelled as simple multi-shape clumps, while soft rubber particles are modeled by using deformable 35-ball body-centered-cubic clusters. Mixtures are prepared with different volumetric rubber content (VRC) at 0, 10, 25, 40 and 100%, statically compressed under 30, 60 and 100 kPa vertical stress and then sheared, by closely simulating a reference laboratory test procedure. The variation of micro-scale factors such as fabric, normal and tangential force anisotropy is carefully examined throughout the shearing process and described by means of novel micro-mechanical relationships valid for GRMs. Moreover, strong-force chains are scrutinized to identify the transition from rigid to soft granular skeleton and gain insights on the load transfer and deformation mechanisms of GRMs. It is shown that the development of the fabric and force anisotropy during shearing is closely related to the macro-scale shear strength of GRMs, and strongly depends on the VRC. Besides, strong-force chains appear to be primarily formed by gravel-gravel contacts (resulting in a rigid-like mechanical behavior) up to VRC = 30%, and by rubber-rubber contacts (causing a soft-like mechanical response) beyond VRC = 60%. Alternatively, at 30% < VRC < 60%, gravel-rubber contacts are predominant in the strong-force network and an intermediate mechanical behavior is observed. This is consistent with the behavioral trends observed in the macro- and micro-mechanical responses.     

Post-erosion mechanical responses of internally unstable gap-graded soil under drained torsional simple shear and triaxial compression

Internal erosion is a major threat to hydraulic earth structures, such as river levees and dams. This paper focuses on suffusion and suffosion phenomena which are caused by the movement of fine particles in the granular skeleton due to seepage flow. The present study investigates the impact of internal erosion on the dynamic response under cyclic torsional shear and monotonic responses under triaxial compression and torsional simple shear. A series of experiments, using a gap-graded silica mixture with a fines content of 20%, is performed under loose, medium, and dense conditions using a novel erosion hollow cylindrical torsional shear apparatus. The erosion test results indicate that the critical hydraulic gradient and the rate of erosion are density-dependent, where a transition from suffosion to suffusion is observed as the seepage continues. Regardless of the sample density, variations in the radial strain and particle size distribution, along the specimen height after erosion, are no longer uniform. Furthermore, the dynamic shearing results show that the small-strain shear modulus increases, but the initial damping ratio decreases after internal erosion, probably due to the removal of free fines. In addition, the elastic threshold strain and reference shear strain values are found to be higher for the eroded and non-eroded specimens, respectively. Finally, based on drained monotonic loading, the post-erosion peak stress ratio increases remarkably under triaxial compression, while that under torsional simple shear depends on the relative density where the direction of loading is normal to the direction of seepage. These observations indicate that the horizontal bedding plane becomes weaker, while the vertical one becomes stronger after downward erosion.     

Effect of geotextile ageing and geomembrane surface roughness on the geomembrane-geotextile interfaces for heap leaching applications

A series of large scale direct shear experiments is used to investigate the effect of the geomembrane (GMB) surface roughness, geotextile (GTX) properties, and GTX ageing, on the GMB-GTX interface shear behaviour. Interfaces involving smooth, coextruded textured, and structured surface GMBs underlying four different nonwoven needle-punched staple fibres (GTXs) with mass per unit areas between 200 and 2400 g/m², and a geocomposite drain (GCD) are examined at normal stresses between 250 and 1000 kPa. The results showed that the interlocking between the GMB and GTX increased with increasing the GMB asperity height and/or decreasing the mass per unit area of the GTX. For the interfaces that involved GTXs preaged prior to the shear box experiments for up to 2 years at 85 °C, it was found that the 2400 g/m² heat bonded two-layered GTX exhibited internal shear failure at low shear displacements. However, all the highly aged single layered GTXs showed an increase in the peak interface friction angles with the increase in their ageing. For these single layered GTX, the results suggest that assessing the interface friction angles using unaged GTXs for the stability analysis is conservative as long as the GTX remains intact in the field.     

Role of particle shape on the shear strength of sand-GCL interfaces under dry and wet conditions

Interface shear strength of geosynthetic clay liners (GCL) with the sand particles is predominantly influenced by the surface characteristics of the GCL, size and shape of the sand particles and their interaction mechanisms. This study brings out the quantitative effects of particle shape on the interaction mechanisms and shear strength of GCL-sand interfaces. Interface direct shear tests are conducted on GCL in contact with a natural sand and a manufactured sand of identical gradation, eliminating the particle size effects. Results showed that manufactured sand provides effective particle-fiber interlocking compared to river sand, due to the favorable shape of its grains. Further, the role of particle shape on the hydration of GCL is investigated through interface shear tests on GCL-sand interfaces at different water contents. Bentonite hydration is found to be less in tests with manufactured sand, leading to better interface shear strength. Grain shape parameters of sands, surface changes related to hydration and particle entrapment in GCL are quantified through image analysis on sands and tested GCL surfaces. It is observed that the manufactured sand provides higher interface shear strength and causes lesser hydration related damages to GCL, owing to its angular particles and low permeability.     

Stability assessment of 3D reinforced soil structures under steady unsaturated infiltration

Internal stability assessment of geosynthetic-reinforced soil structures (GRSSs) has been commonly carried out assuming plane-strain conditions and dry backfills. However, failures of GRSSs usually show three-dimensional (3D) features and occur under unsaturated conditions. A procedure based on the kinematic limit-analysis method is proposed herein to assess 3D effects and the role of steady unsaturated infiltration on the required geosynthetic strength for GRSSs. A suction stress-based framework is used to describe the soil stress behavior under steady unsaturated infiltration. Based on the principle of energy-work balance, the required geosynthetic strength is determined. A comparison analysis with the prior research is conducted to verify the developed method. Two kinds of backfills, i.e., high-quality backfill and marginal backfill, are considered for comparison in this work. It is shown that accounting for 3D effects and the role of unsaturated infiltration considerably reduces the required geosynthetic strength. The 3D effects are primarily affected by the width-to-height ratio of GRSSs, and the contribution of unsaturated infiltration is mainly influenced by the soil type, flow rate, GRSS's height, and location of the water table.     

Liquefaction behavior of fiber-reinforced calcareous sands in unidirectional and multidirectional simple shear tests

A study on the liquefaction resistance of calcareous sands reinforced with polypropylene fibers was reported. Stress-controlled cyclic simple shear tests were conducted on specimens prepared at a relative density of 50%, with and without fiber reinforcements. The liquefaction behavior was investigated by considering the effects of fiber contents ranging from 0% to 1%, fiber lengths varying from 3 mm to 12 mm and loading patterns. The results indicated that increasing fiber content and fiber length resulted in a decrease in the deformation, a reduction in pore pressure accumulation rate, and improved the liquefaction resistance of calcareous sands. Additionally, the risk of soil liquefaction could be significantly reduced when the fiber content was greater than 0.8%. The multidirectional loading had a considerable effect in reducing the liquefaction resistance compared to unidirectional loading. Further, the stiffness degradation of calcareous sands decreased with increasing fiber content and fiber length. The pore pressure generated in the cyclic tests was analyzed and was found to be affected by fiber content. A pore pressure prediction model was proposed to obtain the pore pressure characteristics of fiber-reinforced calcareous sands under various fiber content conditions.