Post-erosion mechanical responses of internally unstable gap-graded soil under drained torsional simple shear and triaxial compression

Internal erosion is a major threat to hydraulic earth structures, such as river levees and dams. This paper focuses on suffusion and suffosion phenomena which are caused by the movement of fine particles in the granular skeleton due to seepage flow. The present study investigates the impact of internal erosion on the dynamic response under cyclic torsional shear and monotonic responses under triaxial compression and torsional simple shear. A series of experiments, using a gap-graded silica mixture with a fines content of 20%, is performed under loose, medium, and dense conditions using a novel erosion hollow cylindrical torsional shear apparatus. The erosion test results indicate that the critical hydraulic gradient and the rate of erosion are density-dependent, where a transition from suffosion to suffusion is observed as the seepage continues. Regardless of the sample density, variations in the radial strain and particle size distribution, along the specimen height after erosion, are no longer uniform. Furthermore, the dynamic shearing results show that the small-strain shear modulus increases, but the initial damping ratio decreases after internal erosion, probably due to the removal of free fines. In addition, the elastic threshold strain and reference shear strain values are found to be higher for the eroded and non-eroded specimens, respectively. Finally, based on drained monotonic loading, the post-erosion peak stress ratio increases remarkably under triaxial compression, while that under torsional simple shear depends on the relative density where the direction of loading is normal to the direction of seepage. These observations indicate that the horizontal bedding plane becomes weaker, while the vertical one becomes stronger after downward erosion.     

Stability assessment of 3D reinforced soil structures under steady unsaturated infiltration

Internal stability assessment of geosynthetic-reinforced soil structures (GRSSs) has been commonly carried out assuming plane-strain conditions and dry backfills. However, failures of GRSSs usually show three-dimensional (3D) features and occur under unsaturated conditions. A procedure based on the kinematic limit-analysis method is proposed herein to assess 3D effects and the role of steady unsaturated infiltration on the required geosynthetic strength for GRSSs. A suction stress-based framework is used to describe the soil stress behavior under steady unsaturated infiltration. Based on the principle of energy-work balance, the required geosynthetic strength is determined. A comparison analysis with the prior research is conducted to verify the developed method. Two kinds of backfills, i.e., high-quality backfill and marginal backfill, are considered for comparison in this work. It is shown that accounting for 3D effects and the role of unsaturated infiltration considerably reduces the required geosynthetic strength. The 3D effects are primarily affected by the width-to-height ratio of GRSSs, and the contribution of unsaturated infiltration is mainly influenced by the soil type, flow rate, GRSS's height, and location of the water table.     

Consolidation considering increasing soil column radius for dredged slurries improved by vacuum preloading method

Soil column is often investigated in the improvement of dredged slurries. Different from the smear zone, the soil column forms gradually and has extremely low permeability. This study presents an analytical solution for soil consolidation considering the increasing radius of the soil column and time-dependent discharge capacity. Based on the solution, the influence of the radius' increase on the consolidation behavior is found significant when the soil column has low permeability and large final radius, and the increase of formation time can lead to the increase of consolidation speed and final consolidation degree.     

Experimental study on the load bearing behavior of geosynthetic reinforced soil bridge abutments with different facing conditions

This paper presents an experimental study on reduced-scale model tests of geosynthetic reinforced soil (GRS) bridge abutments with modular block facing, full-height panel facing, and geosynthetic wrapped facing to investigate the influence of facing conditions on the load bearing behavior. The GRS abutment models were constructed using sand backfill and geogrid reinforcement. Test results indicate that footing settlements and facing displacements under the same applied vertical stress generally increase from full-height panel facing abutment, to modular block facing abutment, to geosynthetic wrapped facing abutment. Measured incremental vertical and lateral soil stresses for the two GRS abutments with flexible facing are generally similar, while the GRS abutment with rigid facing has larger stresses. For the GRS abutments with flexible facing, maximum reinforcement tensile strain in each layer typically occurs under the footing for the upper reinforcement layers and near the facing connections for the lower layers. For the full-height panel facing abutment, maximum reinforcement tensile strains generally occur near the facing connections.     

Effect of the particle size ratio on macro- and mesoscopic shear characteristics of the geogrid-reinforced rubber and sand mixture interface

As a new type of material for civil engineering projects, the rubber and sand mixture is widely used in roadbed fillers, offering environmental benefits over traditional tyre disposal methods. This study uses a large-scale direct shear apparatus to examine the interface shear properties of the geogrid-reinforced rubber and sand mixture, considering different particle size ratios (r), rubber contents, and normal stresses. Based on indoor tests, direct shear models of the mixture with different values of r are established in PFC^3D, revealing the meso-mechanical mechanism of the mixture in the direct shear process. The results show that when r is greater than 1, incorporating a certain amount of rubber particles can increase the shear strength of the mixture. The r values of 15.78, 7.63, and 3.98 correspond to an optimal rubber content of 30%, 10%, and 20%, respectively. When r is less than 1, mixing rubber particles can only reduce the shear strength of the mixture. When the rubber content is low, the smaller the value of r, the greater is the thickness of the shear band. Furthermore, the normal and tangential contact forces are greater. The fabric anisotropy evolution law of the mixture is consistent with the change in the contact force distribution.     

Structural damage and shear performance degradation of fiber–lime–soil under freeze–thaw cycling

The freeze–thaw cycling damages the soil structure, and the shear performance of soil are degraded. A series of tests on lime–soil(L–S) and fiber–lime–soil(F–L–S), including freeze–thaw test, the triaxial compression test, nuclear magnetic resonance (NMR) test and scanning electron microscope (SEM) test, were completed. The test results showed that fiber reinforcement changed the stress–strain behavior and failure pattern of soil. The cohesion and internal friction angle of soil gradually decreased with the increase of freeze–thaw cycles (F–T cycles). The pore radius and porosity of soil increased, while the micro pore volume decreased, and the small pore volume, medium pore volume and large pore volume increased, and the large pore volume had a little variation after 10 F–T cycles. The number of pores of F–L–S was less than L–S, demonstrating that the addition of fiber helped to reduce the pore volume. The interweaved fibers limited the development and the connection of cracks. By means of the spatial restraint effect of fiber on the soil and the friction action between fiber and soil, the shear performances and freeze–thaw durability of F–L–S better were than that of L–S.     

火花放电原子发射光谱类型标准化校正方式的探讨

在国内,火花放电原子发射光谱分析广泛使用类型标准化进行方法校正。在国外,标准和文献中鲜见使用此方法的相关论述。类型标准化主要采用平移校正和转动校正两种方式,哪种方式更加合理也鲜见报道。国外设备类型标准化的默认设置优先采用转动校正方式,相关国内标准对最优校正方式的规定尚不明确,此默认设置的合理性有待探讨。实验选用低合金钢20CrNi2Mo、R407标准样品和不锈钢317L、0Cr18Ni9标准样品,引用国内相关标准,以正确度临界差为评判依据,模拟类型标准化样品和待测样品“十分接近”和“接近”两种情况下平移校正和转动校正的数据正确度。经数据统计分析,平移校正分析结果均满足要求,转动校正结果在“接近”情况下部分元素不满足要求。结合相关国家标准中元素含量范围和精密度数据进行分析,通过计算允许最大偏倚量并制作曲线图方式展开分析,得出如下结论:在满足文中类型标准化控制要点前提下,分析设置更适合于采用平移校正方式。     

渗流作用下新型装配重力式挡土墙有限元分析

为研究渗流作用下新型装配重力式挡土墙应力变化及墙体排水通道对墙后土体固结的影响,采用ABAQUS进行有限元分析,有限元分析结果与模型试验结果相吻合,证明该模型的合理性。在此基础上研究渗流作用下墙体应力变化趋势及墙体排水通道对墙后土体固结效果的影响。研究结果表明:横向排水通道对墙后土体固结效果的影响优于纵向排水通道对土体固结效果的影响,墙体底部横向排水通道的影响作用最显著;渗流作用下墙体应力由上往下呈先增大后减小的趋势,墙体下部所受最大水平剪应力最大。