辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

自重湿陷性黄土地基预钻孔浸水处理的可靠度设计方法

为解决传统预浸水法存在的浸水时间长、浸水处理范围难以确定等不足,基于土体中水分运移规律,依据可靠度理论、极限状态设计方法及复合 Poisson 过程原理,提出一种消除黄土湿陷性的处理浸水方法——预钻孔浸水法。给出了利用预钻孔浸水法对自重湿陷性黄土地基进行浸水时,水平向及竖直向浸水影响范围的确定模型;在此基础上结合达西定律给出了浸水孔设计参数如孔深、孔间距及浸水孔个数的确定方法。结合铜川某工程,设计进行了现场预钻孔浸水试验,对该方法的合理性进行了验证,并通过现场钻探、现场勘探、室内湿陷性试验等方法对该方法的处理效果进行了评价。该浸水方法具有浸水时间短、浸水影响范围可根据浸水孔布设进行控制等优点,且浸水处理效果良好,完全符合施工要求。     

YOLSO: You Only Look Small Object

Small object detection is challenging and far from satisfactory. Most general object detectors suffer from two critical issues with small objects: (1) Feature extractor based on classification network cannot express the characteristics of small objects reasonably due to insufficient appearance information of targets and a large amount of background interference around them. (2) The detector requires a much higher location accuracy for small objects than for general objects. This paper proposes an effective and efficient small object detector YOLSO to address the above problems. For feature representation, we analyze the drawbacks in previous backbones and present a Half-Space Shortcut(HSSC) module to build a background-aware backbone. Furthermore, a coarse-to-fine Feature Pyramid Enhancement(FPE) module is introduced for layer-wise aggregation at a granular level to enhance the semantic discriminability. For loss function, we propose an exponential L1 loss to promote the convergence of regression, and a focal IOU loss to focus on prime samples with high classification confidence and high IOU. Both of them significantly improves the location accuracy of small objects. The proposed YOLSO sets state-of-the-art results on two typical small object datasets, MOCOD and VeDAI, at a speed of over 200 FPS. In the meantime, it also outperforms the baseline YOLOv3 by a wide margin on the common COCO dataset.     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

Strong tribocatalysis of strontium titanate nanofibers through harvesting friction energy for dye decomposition

Friction is a common clean energy and can be harvested and converted into electricity energy via triboelectricity, which can electrochemically drive dye decomposition in theory. In this work, the tribocatalytic Rhodamine B dye decomposition has been experimentally realized in strontium titanate (SrTiO₃) nanofibers, which are synthesized via a hydrothermal method. In the tribocatalytic dye decomposition process, the friction is exerted in the interface between catalyst surface and a polytetrafluoroethylene (PTFE) Teflon rod setup with the different stirring speed. The RhB dye decomposition ratios of SrTiO₃ nanofibers at these stirring speeds of 200 rpm, 400 rpm, 600 rpm, and 800 rpm are respectively 24.2%, 51.8%, 73.9% and 88.6%, yielding to these reaction rate constants of ～0.0112 h^?1, ～0.0260 h^?1, ～0.0562 h^?1 and ～0.0877 h^?1. The main active species, which play an important role in tribocatalytic process, are the superoxide radicals and holes on basis of the active species quenching experiment results. The excellent tribocatalysis activity makes SrTiO₃ nanofibers potential for application in dye wastewater treatment through utilizing the environmental friction energy.     

Visually deficient working conditions and reduced work performance in office workers: Is it mediated by visual discomfort?

IntroductionThe main purpose of this cross-sectional study was to investigate whether visual discomfort acts as a mediating factor between perceived visual ergonomic working conditions and self-rated visual performance among office workers who carry out administrative tasks and computer-based work at the Swedish Tax Agency.MethodsA questionnaire was sent to 94 office workers addressing: 1) perceived visual quality of the visual display units; 2) prevalence of eye symptoms; and 3) self-rated visual performance. Eighty-six persons (54 women (63%), 31 men (36%), and 1 of unspecified sex) answered the questionnaire. Multiple regression analysis investigated the association between visual ergonomic working conditions and visual performance, both with and without visual discomfort as a mediator.ResultsThe group mean of the Indexed survey questions indicated a reasonably good quality of visual ergonomic working conditions, a relative absence of eye symptoms, and acceptable self-rated visual performance. Results from multiple regression analysis showed a significant association between perceived visual ergonomic working conditions and self-rated visual performance (r² = 0.30, β = 0.327, p < 0.01). When visual discomfort was used as a mediator, the association between perceived visual ergonomic working conditions and self-rated visual performance remained the same (r² = 0.32, β = 0.315, p < 0.01).DiscussionIt was remarkable to discover that self-rated visual performance was independent of visual discomfort. Possible explanations include exposure factors not included in the current study, such as dry air and sensory irritation in the eyes, psychosocial stress, time spent performing near work activities, or time exposed to visually deficient working conditions.Relevance to industryThe strong connection between satisfaction with visual ergonomic working conditions and productivity in this study has implications for workplace profitability and staff satisfaction. If productivity is enhanced by better visual ergonomic working conditions, then managers of workplaces may be able to improve work outcomes by optimizing the physical work environment.     

Weighted preliminary-summation-based principal component analysis for non-Gaussian processes

For industrial chemical process, preliminary-summation-based principal component analysis (PS-PCA), an amended PCA method was recently provided for coping with both Gaussian and non-Gaussian characteristics. By summing the training and monitoring data respectively, PS-PCA is capable of resolving the issue of non-Gaussian processes and achieves higher fault detection rate than the traditional PCA. However, in the PS-PCA summation operation, all data samples are regarded as the same weight, which results in the fault information of newly-samples may be diluted, leading to significant detection delays. To address this challenge, in this paper, we propose a novel weighted PS-PCA (WPS-PCA) method that employs an exponential weighting scheme to put more emphasis on recent information. Subsequently, a mathematical argument demonstrates that when the number of variables is enough plentiful, the obtained summation combined with the generalized central limit theorem conforms to approximately a Gaussian distribution. The kurtosis relationships indicate this conversion will bring out well-pleasing feasibility for conventional PCA. Ultimately, the proposed technique verifies detection performance using the Tennessee Eastman process, which is compared with the existing PCA and PS-PCA schemes, in terms of the fault detection time and fault detection rate. The simulation studies reveal that the proposed method is efficient and superior.     

An Improved Torque Sensorless Speed Control Method for Electric Assisted Bicycle With Consideration of Coordinate Conversion

In this paper, we propose an improved torque sensorless speed control method for electric assisted bicycle, this method considers the coordinate conversion. A low-pass filter is designed in disturbance observer to estimate and compensate the variable disturbance during cycling. A DC motor provides assisted power driving, the assistance method is based on the real-time wheel angular velocity and coordinate system transformation. The effect of observer is proved, and the proposed method guarantees stability under disturbances. It is also compared to the existing methods and their performances are illustrated through simulations. The proposed method improves the performance both in rapidity and stability.      

定子分段式永磁直线同步电机速度波动抑制方法研究

为了解决定子分段式永磁直线同步电机(PMLSM)存在的因磁阻效应、负载阻力、摩擦力、参数摄动以及动子进出定子时耦合面积变化所造成的控制性能下降的难题,根据动子和定子的耦合状态,提出一种在完全耦合阶段和动子退出定子阶段的分段式控制方法。首先,在动子与定子完全耦合阶段采用改进滑模控制器减小推力波动导致的速度波动,再通过加入扰动观测器降低滑模切换项所带来的抖振现象;在动子退出定子阶段,建立相关电磁参数与动子位置的函数关系,实时补偿由耦合面积变化引起的动子失速,使动子速度在退出时接近给定值。仿真及实验结果表明动定子完全耦合过程中的速度稳态误差为0.005 m/s,收敛时间为0.3 s,动子退出定子阶段的速度波动不超过0.04 m/s,满足定子分段式PMLSM用于长行程自动运输系统对平稳性及快速性的需求。