基于跨临界CO2热泵的茶叶生产能源系统负荷削减潜力

乡村产业中的化石能源设备逐渐被电能技术替代，引起了乡村负荷波动增大、部分时段产生集中高负荷的问题。为了解决以上问题，将低品位清洁能源应用至乡村的茶叶生产中，针对烘茶全过程的工艺要求提出了跨临界CO₂热泵烘茶技术；并以某茶叶生产乡村为对象，对其代表台区的全年日用电量及产茶日负荷进行了分析，得出采用CO₂热泵烘茶后其负荷得到大幅度削减，整体可降低至原负荷的39.6%~46.8%，峰值负荷与平时负荷的比值由原本的13.6降至5.4~6.2。跨临界CO₂热泵应用至农产品生产中可有效缓解乡村供电压力。     

水-油连续螺旋折流板换热器热力性能研究

利用计算流体力学(Computational Fluid Dynamic, CFD)方法，针对连续螺旋折流板换热器建立物理模型和数学模型，在管侧介质为水和壳侧介质为原油条件下，研究不同原油流量及螺旋角对螺旋折流板换热器内部流场、换热性能及阻力性能的影响，并拟合了水油换热时螺旋折流板换热器的Nu、f与Re的关联式。结果表明：22°螺旋角的螺旋折流板换热器与其它较小螺旋角换热器对比，壳侧压降和换热系数逐渐减小，综合换热性能最佳。通过对壳侧原油为层流状态下的阻力系数和对流换热系数关系式进行拟合，更好地指导水-油连续螺旋折流板换热器的热力设计。     

恒湿文物展柜用吸附式空气取水方法

博物馆恒湿文物展柜的湿度控制至关重要，为实现展柜的自动恒湿功能，本文基于吸附式空气取水原理，提出了一种将环境水汽自动补充至恒湿文物展柜系统水箱的方法，并搭建了相应的小型空气取水装置，证明了该方法的可行性；同时，构建了传热传质耦合的空气取水装置数学模型，在获取环境温湿度对装置取水量的影响规律后，分析加热功率和吸附床结构对装置单位能耗取水量的影响；此外，为便于装置的后期推广应用，提出了两个基于吸附床高度和直径的量纲为1参数。结果表明：进口空气的温度对取水量影响较小，但进口空气的湿度对取水量影响较明显，取水量随着湿度增加而增加；加热功率存在最优值，单位能耗取水量随着加热功率先增大后减小；在当前几何参数组合下，两个量纲为1参数η=2、β=4时，装置的单位能耗取水量最高。     

MSCT多期增强扫描在肾脏透明细胞癌中的诊断价值

目的探讨多排螺旋CT(MSCT)多期增强扫描在肾脏透明细胞癌诊断中的规律性,提高对该肿瘤诊断水平。方法回顾性分析2016年1月~2018年6月14例均经手术切除病理证实为肾脏透明细胞癌患者的CT影像资料,所有病例均行MSCT平扫及多期动态增强扫描。结果14例肾脏透明细胞癌形态大多数呈圆形或者类圆形,瘤体最大径范围1.7cm^11.3cm,平均(4.8±1.4)cm,13例CT平扫时肿瘤密度不均匀,呈等低密度,1例呈等密度;12例出现坏死囊变,钙化1例,伴肾盂、肾盏侵犯2例;动态增强扫描可见12例包膜完整,1例均匀性强化,13例不均匀性强化;引入对比剂后皮质期,出现10例病灶强化幅度大于肾皮质,而仅4例低于肾皮质,三期平均CT值分别为110±30Hu,90±15Hu及75±14Hu,其中在实质期出现13例肿瘤强化幅度小于肾实质,仅1例大于肾实质。结论引入对比剂动态增强扫描后,肾脏透明细胞癌在皮质期明显不均匀强化,实质期强化幅度下降显著,呈现出典型的“快进快出”血流动力学强化方式,且肿瘤容易出现坏死、囊变为其特点。     

煤制天然气中氢对X80钢螺旋焊管力学性能的影响

近年来,我国多项煤制天然气示范工程投入运行,X80钢螺旋焊管常用于天然气长输管道建设,其与煤制天然气的相容性直接影响了长输管道的服役寿命和安全可靠性。为研究煤制天然气对国产X80钢螺旋焊管的力学性能影响,分别从埋弧螺旋焊管的母材和螺旋焊缝处取样,在总压为12 MPa,氢气分数为0,1vol%,2.2vol%,5vol%的模拟环境中分别进行慢应变速率拉伸试验和疲劳裂纹扩展速率试验。试验结果表明:含氢量5vol%以下时,煤制天然气对国产X80管线钢强度性能影响很小,但对塑性性能有一定影响,对疲劳裂纹扩展性能影响很大,煤制天然气中氢对母材的疲劳裂纹扩展性能劣化影响比螺旋焊缝严重。     

Improved district heating network operation by the integration of high-temperature heat pumps

Biomass combined heat and power (CHP) plants connected to district heating networks are a very good opportunity to increase the share of renewable sources into energy systems. Frequently, important consumers are connected to ensure a stable base heat demand throughout the year but they often have higher requirements in terms of temperature (i.e. steam), which involves a high level of temperature in the district heating network during the whole year and high levels of heat losses in the network. This contribution presents the possibility to decrease the level of temperature at which the district heating network operates and to use high-temperature heat pumps connected locally at the consumption point to produce steam when it is required. An investigation of the global design and integration through thermodynamic simulation models is realised for the University of Liège district heating network. This study is intended to determine the heat pump coefficient of performance and, therefore, to assess the balance between the savings in terms of heat losses and the additional heat pump electricity consumption.     

内插螺旋立式上行管流场及传热性能的实验研究

通过粒子图像测速流场实验与传热实验相结合，研究了内插螺旋立式上行管的螺旋节距、丝径、中径比等结构参数在不同Re下对流场、阻力及传热性能的影响。结果表明，内插螺旋能够有效扰动和混合管内流体，使管内形成多个纵向旋涡的流体结构、增大管壁附近液体涡量，有利于强化传热。当Re相同时，管内平均流速v、Nu和综合换热性能PEC均随丝径增大而增大，随中径比减小而增大；随节距增大，3种参数均出现增大的趋势，节距大于20 mm后开始减小。管内流体的阻力f随丝径和节距增大而减小，随中径比增大而增大。综合比较，在较低Re时，节距p=20 mm、丝径e=1.6 mm、中径比D/d=0.75时综合传热效果最好。     

A systemic framework and analysis of urban water energy

Energy impacts of urban water systems are substantial, but not typically analysed systemically. We develop a new system boundary framework including a utility, the ‘bulk water supply authority’ (SB1); the ‘urban water system’ including water use (SB2); and the ‘regional water system’ (SB3). We use the framework to review existing models and show that most address only one boundary. We apply the framework to quantify thermal equivalents of water-related energy in SB1 and SB2, and identify that over 96% of water-related energy in South East Queensland (SEQ) is outside SB1 and within SB2. Consideration of energy influenced by water use is paramount to systemic energy efficiency and optimisation in the urban water system. Clear articulation of system boundaries will improve modelling and management of the energy impact of urban water. Systemic modelling will help decision makers answer increasingly integrated and cross-system and sector questions regarding water and energy interactions.     

A survey on fog computing for the Internet of Things

Fog computing has emerged to support the requirements of IoT applications that could not be met by today’s solutions. Different initiatives have been presented to drive the development of fog, and much work has been done to improve certain aspects. However, an in-depth analysis of the different solutions, detailing how they can be integrated and applied to meet specific requirements, is still required. In this work, we present a unified architectural model and a new taxonomy, by comparing a large number of solutions. Finally, we draw some conclusions and guidelines for the development of IoT applications based on fog.