Fabrication and properties of diatomite ceramics with hierarchical pores based on direct stereolithography

Porous diatomite ceramics with hierarchical pores and high apparent porosity (50.29–56%) were successfully fabricated via direct stereolithography. The pre-ball-milling time, dispersant type and dispersant concentration were systematically investigated to prepare diatomite pastes with high solid loading, low viscosity and a self-supporting effect. The results showed that a pre-ball-milling time of 24 h was more suitable to prepare diatomite pastes with high solid loading, and Span80 at 2 wt% was the optimal dispersant to obtain 40 vol% diatomite paste with a low viscosity and a self-supporting effect. To restrain the formation of defects, a heating rate as low as 0.2 °C/min was allowed to control the pyrolysis rate in the multistage debinding process. At sintering temperatures ranging from 900 °C to 1000 °C, porous diatomite ceramics exhibited a typical bimodal porosity, high apparent porosity and great flexural strength.     

一种用于电气设备状态监测的新式FBG传感器北大核心CSCD

为了监测绕组变压器的静态应力场和发生短路等故障时的动态应力变化,设计了一种用于电气设备状态监测的新式FBG传感器。该传感器由聚醚醚酮材料封装的FBG构成,通过内部圆锥形空腔结构实现将轴向应力集中于FBG敏感位置。通过仿真对不同压力强度下传感器结构的应力场部分及形变趋势进行了计算与分析,论证了设计的合理性。实验分别对静态载荷和动态冲击进行测试,结果显示,在静态压载测试中,当100 N相似文献   

两种混合单元混合机理的数值模拟

为了研究SV型和SX型混合单元在全静态乳化器的混合机理,使用群体平衡模型对乳化器内部流场进行模拟分析。结果表明,SV型与SX型混合单元的混合机理是油相与水相材料通过混合单元时其空间流动方向改变,在流场内形成大量的漩涡,从而达到乳化的目的;通过比较流体在经过SV型和SX型混合单元后的水相索特平均直径(d_(32)),得出SV型混合单元的乳化效果更强,但同时消耗更多的能量,压降更大。     

Evaluation of a sulfidogenic system fed with microalgal biomass of Chlorella pyrenoidosa as an electron donor: Sulfate reduction kinetics

In this study, a sulfidogenic reactor fed with microalgal biomass of Chlorella pyrenoidosa as an electron donor was operated in a continuous mode. This study evaluated the influence of various initial sulfate concentration from 1.0 to 2.5 g/L on anaerobic sulfate reduction kinetics by a sulfidogenic enrichment culture predominantly Desulfovibrio sp. VSV2. It was observed that volumetric sulfate reduction rate (VSRR) was consistently increasing with an increase in volumetric sulfate loading rate (VSLR) across the retention time of 7–10 days. For a retention time of 7 days, the maximum VSRR was noted as 0.0050 g/(L.h) with a corresponding VSLR of 0.0089 g/(L.h). When retention time was maintained for 10 days, a maximum sulfate reduction of 65% and a maximum bacterial concentration of 1.632 g/L were achieved for an initial sulfate concentration of 1.5 g/L. It was concluded that VSLR facilitated through both dilution rate and initial sulfate concentration had a significant influence over sulfate reduction kinetics. The results of the study suggested that the microalgal-fed sulfidogenic system could be effectively employed for reduction of sulfate from sulfate-rich wastewater.     

Ferulic acid and EGCG alter the structural characteristics of ovalbumin and its application in mineral loading

This study aims to fabricate mineral-loading nanocarriers using natural materials. The interaction patterns between ovalbumin (OVA) and four water-soluble polyphenols, namely ferulic acid (FA), (-)-Epigallo-catechin 3-gallate (EGCG), gallic acid (GA) and epicatechin (EC), were investigated. Results showed that the optimised conditions for preparing stable OVA–polyphenol complexes are at the OVA–polyphenol ratio of 4:1 at pH 6, under which OVA–FA and OVA–EGCG showed the highest stability and mineral-loading capacity among four OVA–polyphenol complexes. The fluorescence results indicated that the addition of EGCG and FA induced a significant fluorescence quenching to OVA. The interaction between OVA and polyphenols involved hydrogen bonding, hydrophobic interaction and electrostatic interaction. Fourier transform infrared spectroscopy (FTIR) analysis suggested that both FA and EGCG enhanced the stability and orderliness of the structure of OVA. The transmission electron microscopy images also exhibited the spherical structure of OVA after the addition of FA and EGCG. Furthermore, scanning electron microscope–energy dispersive X-ray spectrum results suggested that OVA–FA and OVA–EGCG complexes were better mineral carriers than OVA–GA and OVA–EC. This study may serve as the theoretical support for the promising application of OVA in the fabrication of mineral-loading nanocarriers in functional food and pharmaceutic.     

Influence of density on the post-suffusion behavior of gap-graded sand with fines

Suffusion erosion, characterized as the selective detachment and transportation of finer particles by seepage flow, is hazardous to the stability and serviceability of geotechnical structures. The removal of finer particles deteriorates the structure and fabric of the soil, leading to the degradation of its mechanical properties. Studies into the effects of suffusion on mechanical behavior have so far produced disparate results depending on the pre-erosion relative density of the specimens tested. To investigate this issue, small cyclic and monotonic loading tests were performed on intact and eroded gap-graded silty sand specimens in three dispersed density states, using a triaxial cell modified for the purpose of erosion. The variation of Young's modulus showed an inverse relationship with the pre-erosion density of the specimen, as the small strain stiffness decreased in the dense cases and increased in the loose cases. Conversely, Poisson's ratio increased in value as suffusion progressed regardless of the initial density of the specimens. In the contractive phase of monotonic loading, the densification of the coarse soil skeleton by the downward seepage flow resulted in a decrease in contractiveness and an increase in secant stiffness. In the dilative phase, the increase in porosity by the erosion of finer particles reduced the dilatancy and peak strength of the specimens. The results suggest that the pre-suffusion density determines the primary locus of affected mechanical behavior in triaxial compression, which shifts from the contractive phase to the dilative phase with the increase in pre-suffusion density. The critical state strength, inferred using stress–dilatancy theory, was largely unaffected by the erosion of finer particles. As the results indicate, pre-erosion density may be of practical significance in assessing the vulnerability to deterioration and collapse of geotechnical formations and structures subjected to suffusion erosion.     

Liquefaction behavior of fiber-reinforced calcareous sands in unidirectional and multidirectional simple shear tests

A study on the liquefaction resistance of calcareous sands reinforced with polypropylene fibers was reported. Stress-controlled cyclic simple shear tests were conducted on specimens prepared at a relative density of 50%, with and without fiber reinforcements. The liquefaction behavior was investigated by considering the effects of fiber contents ranging from 0% to 1%, fiber lengths varying from 3 mm to 12 mm and loading patterns. The results indicated that increasing fiber content and fiber length resulted in a decrease in the deformation, a reduction in pore pressure accumulation rate, and improved the liquefaction resistance of calcareous sands. Additionally, the risk of soil liquefaction could be significantly reduced when the fiber content was greater than 0.8%. The multidirectional loading had a considerable effect in reducing the liquefaction resistance compared to unidirectional loading. Further, the stiffness degradation of calcareous sands decreased with increasing fiber content and fiber length. The pore pressure generated in the cyclic tests was analyzed and was found to be affected by fiber content. A pore pressure prediction model was proposed to obtain the pore pressure characteristics of fiber-reinforced calcareous sands under various fiber content conditions.     

Revisit the Pitot static tubes in the standards

A Pitot tube is a popular device used for the measurements of flow fields. To control the accuracy of the Pitot tube coefficient, the international standard organization (ISO), the American Society for Testing and Materials (ASTM), and the Japanese Industrial Standards (JIS) issued guidelines that recommended the shape and working conditions of these devices. However, many Pitot tubes on the market do not follow these guidelines. In the present study, various types of Pitot tubes in the market were tested at the National Metrology Institute of Japan (NMIJ) to determine the effects of the geometry and flow characteristics. The results revealed certain limitations in the existing ISO and JIS standards, specifically with regard to the recommended design parameters of the AMCA Pitot tube, the reference coefficient value for the JIS Pitot tube, and the redefinition and limitation of Reynolds numbers pertaining to Pitot tube working conditions.     

矿用提升机盘形制动器制动安全分析

通过解析矿用提升机制动器制动的工作原理,分析影响安全制动的因素,可以在工作中尽快找出影响安全制动的原因,并采用相应的解决方法使提升机在有效制动范围内运行。     

A hidden Markov model to detect regime changes in cryptoasset markets

The objective of this work is to understand the dynamics of cryptocurrency prices. Specifically, how prices switch between different regimes, going from “bull” to “stable” and “bear” times. For this purpose, we propose a hidden Markov model that aims at explaining the evolution of Bitcoin prices through different, unobserved states. The implementation of the proposed model includes a likelihood ratio test that allows to compare models with different states and with different covariance structures. Our empirical findings show that the time movements of Bitcoin prices across different exchange markets are well-described by the proposed model. In particular, a parsimonious model with a diagonal covariance matrix leads to better predictions, compared with a model with a full covariance matrix.