首页 | 本学科首页   官方微博 | 高级检索  
文章检索
  按 检索   检索词:      
出版年份:   被引次数:   他引次数: 提示:输入*表示无穷大
  收费全文   1289篇
  免费   66篇
  国内免费   58篇
电工技术   1篇
综合类   72篇
化学工业   150篇
金属工艺   358篇
机械仪表   402篇
矿业工程   15篇
能源动力   2篇
轻工业   4篇
石油天然气   117篇
武器工业   3篇
无线电   7篇
一般工业技术   224篇
冶金工业   54篇
原子能技术   3篇
自动化技术   1篇
  2024年   7篇
  2023年   45篇
  2022年   53篇
  2021年   59篇
  2020年   48篇
  2019年   58篇
  2018年   58篇
  2017年   88篇
  2016年   57篇
  2015年   50篇
  2014年   43篇
  2013年   46篇
  2012年   81篇
  2011年   79篇
  2010年   59篇
  2009年   68篇
  2008年   43篇
  2007年   97篇
  2006年   100篇
  2005年   85篇
  2004年   57篇
  2003年   31篇
  2002年   36篇
  2001年   16篇
  2000年   17篇
  1999年   9篇
  1998年   4篇
  1997年   5篇
  1996年   5篇
  1994年   2篇
  1993年   3篇
  1992年   2篇
  1989年   1篇
  1988年   1篇
排序方式: 共有1413条查询结果,搜索用时 15 毫秒
1.
本研究分别采用多巴胺-端环氧基硅油与硝酸-端环氧基硅油体系改性碳纤维,对比了纤维表面形貌和化学官能团的变化,探究了化学协同改性机理。进一步表征了纸基摩擦材料的表面形貌、粗糙度及孔隙结构,研究了协同改性对纸基摩擦材料力学和摩擦学性能的影响规律。结果表明,硝酸-端环氧基硅油改性体系更有利于提升纸基摩擦材料力学强度和耐磨性,改性后纸基摩擦材料的拉伸强度和层间剪切强度分别较改性前提高了25.8%和23.6%,磨损率降至0.620×10-8 cm3/J;相比于多巴胺预处理,硝酸刻蚀过程不仅可以增加后续端环氧基硅油接枝改性的活性位点,同时提高了碳纤维与树脂间的化学交联密度。  相似文献   
2.
Based on the three-cathode plasma spraying system, tantalum (Ta) coatings were prepared on the substrate of CuCrZr alloy. The effects of different auxiliary gas (helium) flow rates on the microstructure, phase composition, mechanical and wear resistance properties of Ta coatings were studied. The results showed that the oxidation degree of the coatings decreases first and then increases with the increase of the auxiliary gas flow. When the auxiliary gas flow rate is 70 L·min–1, the oxidation degree of the coating is the lowest, minimum value of the porosity is 0.21%, and the bonding strength reaches the maximum, 59.3 MPa. At this time, the coating wear rate is 0.0012 mm3·N–1·m–1 with the best wear resistance. This indicates that the auxiliary gas flow has an important influence on the quality and surface mechanical properties of tantalum coating.  相似文献   
3.
Al-xNi-yCeO2 (x = 6, 10, 15, 20 and y = 0, 5, 10 wt%) composites were produced by a powder metallurgical production route. Powder mixtures of Al, Ni and CeO2 were fabricated via mechanical alloying (MA) for 4 h in a Spex-type high-energy ball mill. Both the mechanically alloyed (MAed) and non-MAed (as-blended mixtures) powders were pre-compacted in a hydraulic press under 650 MPa and then pressurelessly consolidated at 630 °C for 2 h under an inert atmosphere. The effects of MA process and the amounts of Ni and CeO2 on the microstructural, mechanical and tribological properties of the sintered composites were determined. Based on the SEM and XRD investigations, the MAed powders illustrated a homogenous structure, comprising flaky particles with smaller crystallite sizes and greater lattice strain. According to the XRD analysis, Ni formed Al–Ni intermetallic compounds in the matrix of sintered composites that act as secondary reinforcement phases. The SEM observations conducted on the MAed samples demonstrated more uniformly and finely distributed Al3Ni and CeO2 phases in the microstructure of the MAed samples, unlike the non-MAed ones. The hardness values of sintered composites increased due to the MA process and increasing Ni and CeO2 amounts, and the hardness value of the MAed Al20Ni–10CeO2 sample reached 179 HV. The ultimate compressive strength and failure strain of the MAed Al6Ni–10CeO2 sample were 441 MPa and 11.3%. In the Al20Ni–10CeO2 sample, the compressive strength and failure strain were 391 MPa and 5.5%, respectively. Additionally, the reciprocating wear test results illustrated that both wear resistance and hardness values of the composites increased as the amounts of Ni and CeO2 increased, and the Al20Ni–10CeO2 sample exhibited the highest wear resistance as 0.175 × 10-3 mm3/Nm.  相似文献   
4.
外加电磁场是改善摩擦副摩擦学性能的途径之一。从外加电磁场对位错运动的促进、接触表面氧化的增强和磨屑的细化氧化3个方面,综述了电磁场对金属材料摩擦副摩擦学性能改善的机理,介绍了外加电磁场类型、磁场强度、磁场施加方向、磁场频率以及摩擦副材料的磁导率大小及差异、外加磁性颗粒尺度对摩擦副摩擦磨损的影响,指出了未来电磁场抗磨减摩的研究方向。  相似文献   
5.
采用干压擦筛造粒法制备了炭黑造粒颗粒,研究了炭黑造粒颗粒质量分数对Cu-Fe摩擦材料显微组织、力学性能、摩擦性能的影响。结果表明:炭黑造粒颗粒易被压制成条状形态,当炭黑造粒颗粒质量分数较低时,其与金属基体能形成完整的界面,而含量较高时界面易出现孔洞和裂纹;随着炭黑造粒颗粒质量分数的增加,摩擦材料的力学性能先增加后降低、摩擦系数和磨损量均先降低后增加。当炭黑造粒颗粒质量百分数为5%时,摩擦材料的力学性能最大,摩擦系数最低,磨损量最小,材料的综合性能最佳。  相似文献   
6.
This study highlights the scratch adhesion failure characterization and tribo-mechanical properties of physical vapor deposited (Cr, Ti) N coating on AA7075-T6 by using magnetron-sputtering technique. The surface morphology, microstructure and chemical composition of CrTi/CrTiN film were inspected by an optical microscope, scanning electron microscope (SEM) incorporated with energy dispersive X-ray spectroscopy (EDX) in addition to focused ion beam milling. The coating to substrate critical load of about 1261 mN was obtained, by employing coating deposition parameters of; DC power (300 W, RF power (200 W)), temperature (300 °C) and nitrogen flow rate (6%). Failure adhesion characteristics exhibited initial arc-tensile cracking followed by chipping and spallation that led to complete coating failure at Lc3. The tribo-mechanical aspects were evaluated by a pin-on-plate reciprocating testing unit, which showed a lower friction coefficient of 0.36 for CrTiN as compared with 0.43 for AA7075-T6. Subsequently, the wear depth was also reduced from 9.5 to 5.9 μm. It was revealed that the wear mechanism for AA7075-T6 was extensive deformation, abrasion and delamination, while the CrTiN exhibited slightly oxidative abrasive wear mode.  相似文献   
7.
采用磁控溅射法,通过改变氩氮比率,在Si(100)衬底上成功制备了W2N薄膜,当氩氮比率为20:6时薄膜的结晶性最好.为了改善W2N薄膜的力学和摩擦学性能,采用射频和直流磁控共溅射方法分别在Si(100)和A304不锈钢衬底上制备了软质金属Y和硬质金属Cr共掺杂的W2N(Y-Cr:W2N)薄膜.在掺杂功率20~50 W范围内,当掺杂功率为30 W时,薄膜具有最大硬度,为23.71 GPa,此时样品的弹性模量为256.34 GPa; 当掺杂功率为20 W时,薄膜的平均磨擦系数最小,为0.37.这表明,金属Y和Cr的掺入使W2N薄膜的力学和摩擦学性能有了很大的改善.  相似文献   
8.
为了改善石墨烯在润滑油中的分散稳定性,利用一种高分子量丁二酰亚胺(分散剂A)辅助石墨烯分散于聚α-烯烃(PAO4)基础油中,采用紫外-可见分光光度法对其分散稳定性进行了监测,并使用UMT-3多功能摩擦试验仪和ContourGT-K型三维轮廓仪考察了石墨烯/PAO4分散液的摩擦磨损性能,利用扫描电子显微镜(SEM)、能谱仪(EDS)和X射线光电子能谱(XPS)对磨痕表面的形貌和元素组成进行定性和定量分析。结果表明:分散剂A可有效提高石墨烯在PAO4中的分散稳定性,加入分散剂A后,石墨烯/PAO4分散液静置一周后的相对浓度为0.667,是未加分散剂的分散液的7.8倍;石墨烯作为润滑油添加剂能显著提升摩擦磨损性能,添加0.8 mg/mL的石墨烯和质量分数为0.2%的分散剂A,跑合期从670 s缩短至250 s,磨损体积减少了55%。  相似文献   
9.
采用真空热压制备了三维连续网络Ti2AlC/TiAl复合材料,在明晰其高温氧化行为的基础上,利用摩擦磨损试验机对复合材料的高温氧化磨损行为及其机理进行了研究。结果表明,高温氧化条件下,复合材料表面在600℃以下生成Al2O3藓状氧化物,在800℃时生成TiO2聚集团以及TiO2和Al2O3的氧化物混合层;随着温度的升高,氧化膜的润滑作用使得摩擦系数降至0.3237,基材的软化与TiO2聚集团的突出生长使得磨损速率逐渐升至4.5×10-4mm3/(N.m),磨损机理由磨粒磨损转变为磨粒磨损与氧化磨损的混合磨损。  相似文献   
10.
范祥娟  李文生  崔帅  李建军 《表面技术》2021,50(5):152-159, 191
目的 合理选用摩擦偶件材料,以减缓Ni3Al基涂层宽温域内的摩擦磨损.方法 分别以WC-Co和316L为摩擦偶件,研究25~800℃内其对Ni3Al基涂层润滑和磨损机理的影响.采用高温硬度仪测试摩擦偶件在不同温度时的硬度,采用附带能谱仪的扫描电子显微镜观察磨损表面、磨斑和磨屑的形貌并测试成分,采用拉曼散射仪测试磨损表面和磨斑的成分.结果 在25~800℃,随温度的升高,两种摩擦副的摩擦系数具有一致的变化规律.与WC-Co对摩时,涂层在各温度下均具有低磨损率,且随温度升高,磨损率呈下降趋势.在25~200℃,与316L对摩时,涂层主要表现为粘着磨损和磨粒磨损,而与WC-Co对摩时,涂层在高接触应力下发生塑性变形,抑制Ag润滑相析出和涂层剥落,使其较前者具有高摩擦系数和低磨损率.在400℃,与WC-Co对摩时,高接触应力下产生的摩擦热促使涂层发生轻微的氧化,形成NiO和NiCr2O4,使其减摩性能优于Ni3Al/316L摩擦副.在600~800℃,与316L对摩时,涂层由严重的粘着磨损转变为氧化磨损;而与WC-Co对摩时,涂层由氧化磨损和剥层磨损转变为氧化磨损.此外,800℃时,Ni3Al/316L摩擦副的摩擦磨损发生在光滑润滑膜与粗糙转移膜之间,而Ni3Al/WC-Co摩擦副发生在光滑的润滑膜与转移膜之间.结论 在25~800℃,涂层与316L和WC-Co对摩时均具有良好的减摩性能,且与WC-Co对摩时具有更优的耐磨性能.  相似文献   
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号