Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

CFD Prediction of Flow and Homogenization in a Stirred Vessel: Part I Vessel with One and Two Impellers

A simulation of flow field and tracer homogenization was performed using the commercial CFD software FLUENT 6.1. The aim is to investigate the potential of CFD software to predict concentration distribution of added tracer in cylindrical vessels. The calculated results – dimensionless velocity profiles, power and pumping numbers, dimensionless concentration curves, and mixing times – were compared with experiments in stirred vessels. In Part I, the study was performed for vessels agitated by one or two impellers on a centric shaft. Two different impellers were used – a 6‐bladed 45° pitched blade turbine and a standard Rushton turbine. The standard k‐? turbulence model and multiple reference frames method were used for the simulations. The influence of the grid type was also investigated; three types of grid – a structured, unstructured and a special user‐defined grid – were studied.     

Regional chemotherapy of liver tumors

In the absence of adequate autogenous vein for tibial artery bypass in limb salvage surgery, the use of prosthetic grafts with a distal anastomotic vein cuff or patch has shown promising results. Here, we describe how the Florester Internal Vessel Occluder (Meadox UK, Bedfordshire, UK) can facilitate the construction of a distal anastomotic vein cuff.     

Two Isomers of C60F48: Computed Inter-isomeric Equilibrium

C₆₀F₄₈ has been known to exist in two isomeric forms of D₃ and S₆ symmetries. However, the quantum-chemical calculations have not agreed on their stability order though a near-isoenergetic picture is otherwise always encountered. In order to clarify the situation, the entropy effects are evaluated for synthetic temperatures of about 500K. The entropy evaluations suggest that the D₃ isomer should be more stable in the potential energy by 2.05-2.55 kcal/mol (to which term the ab initio data are closer than the semiempirical ones).     

The influence of preparation conditions on the electrochemical behaviour of CuO in a Li/CuO cell

A dozen CuO samples prepared under various conditions and from different starting materials were evaluated as cathode materials for a primary Li/CuO cell. The “thin electrode” method was used for rapid evaluation of the samples. Both coulombic efficiency and discharge voltage depend considerably on the method of synthesis. No correlation was found between the specific surface area and the resistivity of the samples on the one hand and the cathode performance on the other. Best results were obtained from CuO prepared by the oxidation of Cu₂O under controlled temperature and time of oxidation.     

A review of the metallurgy of heat treatment of welded joints

This paper deals with the metallurgical changes which occur during heat treatment of welded joints. Stress relieving heat treatment in the temperature range below A₁, the normalizing heat treatment and the heat treatment in the intercritical range A₁–A₃, are all considered. The thermal regime of welding is described. The practice of intercover of the weldment before applying PWHT to ambient temperature is described. It is stressed that the aim of stress-relieving heat treatment is not only to relax internal stresses but also to improve the microstructure and impact properties of HAZ and weld metal, to improve dimensional stability and increase resistance against stress corrosion. Examples are given of the effect of annealing in the intercritical range A₁–A₃ on the improvement in toughness of electroslag welded joints. Changes in dislocation distribution and density, precipitation processes and grain sizes during PWHT are described.     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

Portosystemic shunt in Budd-Chiari syndrome: long-term survival and factors affecting shunt patency in 25 patients in Western countries

BACKGROUND: In Budd-Chiari syndrome (BCS) treated by portosystemic shunt, postoperative shunt thrombosis is associated with high morbidity and mortality rates. The aim of this study was to determine factors associated with shunt thrombosis. METHODS: From 1985 to 1991, 25 patients underwent portosystemic shunt for BCS. According to the patency of the shunt during the postoperative period and follow-up, patients were divided into two groups including 17 patients with patent shunt and 8 (32%) with shunt thrombosis. RESULTS: In patients with patent shunt, actuarial survival rate at 5 years was 87% versus 38% in patients with shunt thrombosis (p < 0.05). Duration of symptoms before operation was higher in patients with shunt thrombosis than in patients with patent shunt (315 +/- 483 vs 109 +/- 168 days, p < 0.05). In patients with patent shunt, extensive fibrosis or cirrhosis was observed in 3 of 17 (18%) versus in 5 of 8 (63%) of patients with shunt thrombosis (p < 0.05). Shunt thrombosis was observed in 3 of 3 patients (100%) with the combination of myeloproliferative disorder, duration of symptoms more than 100 days, and cirrhosis versus 0 of 6 (0%) patients without this combination (p < 0.05). CONCLUSIONS: In acute form of BCS (with short history of the disease and absence of extensive fibrosis or cirrhosis), early portal decompression is mandatory, with low risk of shunt thrombosis and good long-term results. In chronic form of BCS, the risk of shunt thrombosis is high and long-term results are bad; in these patients, orthotopic liver transplantation must be considered.     

A Survey on the Numerics and Computations for the Landau-Lifshitz Equation of Micromagnetism

The Landau-Lifshitz (LL)equation of micromagnetism governs rich variety of the evolution of magnetization patterns in ferromagnetic media. This is due to the complexity of physical quantities appearing in the LL equation. This complexity causes also an interesting mathematical properties of the LL equation: nonlocal character for some quantities,nonconvex side-constraints, strongly nonlinear terms. These effects influence also the numerical approximations. In this work, recent developments on the approximation of weak solutions, together with the overview of well-known methods for strong solutions,are addressed. Author is supported by the Fund for Scientific Research - Flanders FWO (Belgium).