弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法

提出了一种新的计算弹性-粘弹性复合结构随机响应的各阶谱矩的计算方法，它是一种时域复模态分析方法。利用此方法获得了弹性-粘弹性复合结构在白噪声、滤过白噪声等典型平稳随机激励下随机响应的各阶谱矩的解析表达式，分析了粘弹性对各阶谱矩的影响。此计算方法简便、易用，无论单自由度或多自由度系统均适用，为进一步研究弹性-粘弹性复合结构在随机激励下的可靠性打下良好基础。     

挖金湾矿近距离煤层联合布置开采可行性研究

提出挖金湾矿近距离煤层联合布置开采方案，并对开采方案的技术难点进行了分析，找出了解决方法。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

导向钻井系统在多目标大井斜定向井中的应用

详细介绍了C-D井在钻进过程中井眼轨迹的控制过程,总结了在C-D井中使用导向钻井系统的成功经验。用1根导向马达、2套钻具组合、3只牙轮钻头顺利地完成了定向、增斜、稳斜及降斜,7个目标点一次击中,且最小靶心距仅0.99m。用15d完成了这口斜深2287.09m、井斜58.40°、水平位移903.11m的多目标定向井,钻穿目标点之多、实钻井眼剖面符合率之高、施工难度之大、速度之快,在目前国内都处于领先地位。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

燃气联合循环的新发展

根据国内外能源结构的调整变化，就我国和世界上其他国家采用燃气联合循环发电的情况以及能电共生新趋势作一些介绍，供规划建设联合循环发电决策参考。     

1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。     

Biogas and biomass technology: Energy generation from biomass and waste in the Netherlands

Within the European Community, the interest in energy generation from biomass and waste is increasing. A brief overview is given of several thermal conversion technologies, of biomass production and waste availability in the Netherlands. Based on this, the possibilities for energy generation from biomass and waste in the Netherlands are evaluated.     

Modified oil agglomeration process for coal beneficiation. III. Grinding and agglomeration using different szego mill designs

The simultaneous grinding/agglormeration process has been used to beneficiate Minto coal. Experiments with the Szego Mill, a planetary ring-roller mill with grooved rollers, have given good results. Different roller ridge/groove sizes have been tested and favourable oil-coal-water ratios established. Ash removal is closely related to grinding performance. Very short mill residence times, of the order of 10 seconds, are sufficient for microagglomerate formation. Considerable equipment and operating cost savings are possible with the modified process.     

地下硐室锚喷支护堵漏防渗处理实践

本文简要地介绍了我国几个地下矿在锚喷网联合支护的硐室工程中堵漏防渗处理所取得的良好效果，可供类似矿山参考。