一种新型的室温快速固化胶黏剂的研制

本文开发了一种新型的方舱夹芯板用室温固化高强度环氧结构胶黏剂,验证了其物化特性、相关力学性能和环境适应性。结果表明此胶黏剂具有优良性能,可以满足方舱用大板胶黏剂的使用需求。     

Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

A novel bio‐based phthalonitrile resin derived from catechin: synthesis and comparison of curing behavior with petroleum‐based counterpart

The development of bio‐based thermosetting resins with good thermal stability can potentially afford sustainable polymers as replacements for petroleum‐based polymers. We report a practical route to a novel catechin‐based phthalonitrile resin precursor (CA‐Ph), which contains free phenolic hydroxyl groups that result in ‘self‐curing’ at elevated temperatures to afford a thermostable polymer. Comparison of the performance of this CA‐Ph resin with that of a conventional petroleum‐based bisphenol A phthalonitrile resin (BPA‐Ph; containing 5 wt% of the curing agent 4,4′‐diaminodiphenylsulfone) revealed that CA‐Ph exhibits a lower melting point and curing temperature. Cured CA‐Ph resin retains 95% of its weight at 520 °C under a nitrogen atmosphere, which compares favorably with results obtained for BPA‐Ph resin that retains 95% of its weight at a lower temperature of 484 °C. Kinetic results indicated that the curing reactions of both CA‐Ph and BPA‐Ph systems follow an autocatalytic mechanism. These results suggest that catechin is a useful bio‐based feedstock for the preparation of self‐curing and thermally stable phthalonitrile resins for advanced technological applications. © 2017 Society of Chemical Industry     

Chloride migration in concrete with superabsorbent polymers

Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixtures are tested 7, 14, and 28 days after casting. The development of degree of hydration is followed for 20 corresponding paste mixtures.Both when SAP is added with extra water to compensate the SAP water absorption in fresh concrete and without extra water, the internal curing water held by SAP may contribute to increase the degree of hydration. No matter if SAP is added with or without extra water, it appears that the so-called gel space ratio can be used as a key parameter to link age and mixture proportions (water-to-cement ratio and SAP dosage) to the resulting chloride migration coefficient; the higher the volume of gel solid relative to the space available for it, the lower the chloride migration coefficient, because the pore system becomes more tortuous and the porosity becomes less.     

含磷固化剂及固化环氧树脂的合成及表征

以4,4′-二氨基二苯基甲烷(DDM)、苯甲醛和亚磷酸二乙酯为原料,合成了两种含磷固化剂PM1和PM2,用红外光谱、核磁共振氢谱对PM1和PM2的结构进行了表征。用DDM,PM1,PM2分别固化双酚A型(DGEBA)环氧树脂,得到DGEBA-DDM,DGEBA-PM1,DGEBA-PM2树脂,采用示差扫描量热法、热重分析(TGA)和极限氧指数(LO I)对DGEBA-DDM,DGEBA-PM1,DGEBA-PM2树脂的玻璃化转变温度(Tg)、反应活性、热稳定性和阻燃性能进行了表征。实验结果表明,PM2的反应活性比PM1低;DGEBA-DDM,DGEBA-PM1,DGEBA-PM2树脂的Tg分别为178,112,145℃;TGA结果表明,700℃时DGEBA-PM1和DGEBA-PM2树脂的成炭率分别为29%和35%,而700℃时DGEBA-DDM树脂的成炭率只有19%;DGEBA-PM1和DGEBA-PM2树脂的LO I值由DGEBA-DDM树脂的24%分别增至30%和35%,且阻燃性能大幅度提高。     

复杂土坝的渗流安全分析评价

根据福华山土坝的渗流观测资料,建立了测压管水位的回归统计模型,定量分析了各影响量(水位分量、时效分量)对测压管水位的影响效应。在此基础上,结合观测资料,采用有限元法反演了大坝各填筑区的渗透系数,并综合评价了大坝的渗流性态。     

Rheological cure characterization of phosphazene–triazine polymers

Cyclomatrix phosphazene–triazine network polymers were synthesized by co‐curing a blend of tris(2‐allylphenoxy), triphenoxy cyclotriphosphazene (TAP), and tris(2‐allylphenoxy) s‐triazine (TAT) with bis(4‐maleimido phenyl) methane (BMM). The co‐curing of the three‐component resin was investigated by dynamic mechanical analysis using rheometry. The cure kinetics of the Diels–Alder step was studied by examining the evolution of the rheological parameters, such as storage modulus (G′), loss modulus (G″), and complex viscosity (η*), for resins of varying compositions at different temperatures. The curing conformed to an overall second‐order phenomenological equation, taking into account a self‐acceleration effect. The kinetic parameters were evaluated by multiple‐regression analysis. The absence of a definite trend in the cure process with blend composition ratio was attributed to the occurrence of a multitude of competitive reactions whose relative rates depend on the reactant ratio and the concentration of the products formed from the initial phase of reaction. The cure was accelerated by temperature for a given composition, whereas the self‐acceleration became less prominent at higher temperature. Gelation was accelerated by temperature. The gel conversion decreased with increase in maleimide concentration and, for a given composition, it was independent of the cure temperature. The activation energy for the initial reaction and the crosslinking process were estimated for a composition with a maleimide‐to‐allyl ratio of 2 : 1. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 908–914, 2003     

柴北缘地区走滑反转构造及其深部地质因素分析

过去普遍认为柴达木盆地北缘地区的冷湖南八仙构造带的深部为向南逆冲的燕山晚期构造,浅部为向北逆冲的喜马拉雅晚期构造.但通过详细层位对比和构造分析,发现冷湖5号、6号、7号构造与南八仙构造基本为喜马拉雅晚期定型的走滑压扭构造,局部构造主体发育多条高角度走滑断层,构造变形集中于断裂带附近,而断裂带之间的凹陷则未发生大的变形,以沉积、沉降作用为特征.深部地质与地球物理特征揭示,柴达木盆地深部地壳存在低速层,地壳块体可能沿深部断裂带发生东西向的拆离作用.构造分析认为,在侏罗系烃源岩的排烃高峰阶段,冷湖6号构造并没有形成圈闭,而冷湖7号构造的高点与现今不一致,因而现在的构造高部位不具备原生油气藏形成条件.冷湖构造带附近为侏罗系断陷分布区,侏罗系厚度较大,原生油气藏可能分布在该带的周缘地区,包括北部斜坡、喜马拉雅运动早中期的构造圈闭与岩性-地层圈闭,继承性凹陷的深部以及由深凹陷内侧断裂带所围限的断块也是油气运聚的有利部位.图4参10     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

Effects of Salting, Drying, Cooking, and Smoking Operations on Volatile Compound Formation and Color Patterns in Pork

ABSTRACT: The traditional small-scale production of boucané, a cured smoked pork-belly product from Réunion, involves several unit operations that are performed in a single step. The aim of this study was to highligh the impact of 4 unit operations (salting, drying, cooking, and smoking) on stability, color, and flavor development in processed pork. These characateristics are the 3 main criteria of boucané's quality. Mass transfer, color, and volatile compounds were measured, analyzed, and compared in 4 products. Results indicated that a major quantity of volatile compounds detected in the processed meat were derived from the smoking process. Color variations were mainly explained by muscle pigment modification due to the cooking process, and by the input of volatile compounds of smoke.