高面板坝全寿命周期变形控制方法及应用

高面板坝的变形对面板的安全运行有着特别重要的影响，国内外已建的高面板坝工程中，因坝体变形大导致防渗面板挤压破损，坝体渗漏量大的实例较多，不得不降低水库水位进行修复处理，造成较大的经济损失乃至给大坝的长期运行留下安全隐患。通过发生挤压破损的实例分析，发现变形控制缺乏系统性是发生面板挤压破损的主要因素，为预防面板破损，系统提出了“控制坝体总变形，转化有害变形，适应纵向变形”的坝体变形控制方法，并在使用软硬岩混合料筑坝的董箐面板堆石坝中得到的应用，取得了良好效果，该工程运行至今达十余年，未见面板有挤压破损迹象，该方法对建设200 m以上乃至300 m级超高面板坝具有重要借鉴意义。     

高效液相色谱法测定化妆品中依克多因的含量

建立高效液相色谱法测定化妆品中依克多因的分析方法,采用Agilent Poroshell 120 EC-C₁₈色谱柱（100 mm×3.0 mm,2.7μm）分离,以甲醇和p H为3.0的40 mmol/L磷酸二氢钠-10 mmol/L 1-庚烷磺酸钠缓冲溶液梯度洗脱,流速0.8 m L/min,柱温30℃,检测波长210 nm。采用外标法定量测定化妆品中的依克多因含量。结果表明,依克多因在5～800 mg/L的质量浓度范围内呈现良好线性关系,相关系数为0.999 8,方法的检出限和定量限分别为0.3和1.0 mg/L。该方法具有分离效率高、分析时间短、节省溶剂等优点,解决了依克多因在C₁₈色谱柱上保留弱的问题。     

Predictive formulas for different measures of cheese yield using milk composition from individual goat samples

The objective of this study was to develop formulas based on milk composition of individual goat samples for predicting cheese yield (%CY) traits (fresh curd, milk solids, and water retained in the curd). The specific aims were to assess and quantify (1) the contribution of major milk components (fat, protein, and casein) and udder health indicators (lactose, somatic cell count, pH, and bacterial count) on %CY traits (fresh curd, milk solids, and water retained in the curd); (2) the cheese-making method; and (3) goat breed effects on prediction accuracy of the %CY formulas. The %CY traits were analyzed in duplicate from 600 goats, using an individual laboratory cheese-making procedure (9-MilCA method; 9 mL of milk per observation) for a total of 1,200 observations. Goats were reared in 36 herds and belonged to 6 breeds (Saanen, Murciano-Granadina, Camosciata delle Alpi, Maltese, Sarda, and Sarda Primitiva). Fresh %CY (%CY_CURD), total solids (%CY_SOLIDS), and water retained (%CY_WATER) in the curd were used as response variables. Single and multiple linear regression models were tested via different combinations of standard milk components (fat, protein, casein) and indirect udder health indicators (UHI; lactose, somatic cell count, pH, and bacterial count). The 2 %CY observations within animal were averaged, and a cross-validation (CrV) scheme was adopted, in which 80% of observations were randomly assigned to the calibration (CAL) set and 20% to the validation (VAL) set. The procedure was repeated 10 times to account for sampling variability. Further, the model presenting the best prediction accuracy in CrV (i.e., comprehensive formula) was used in a secondary analysis to assess the accuracy of the %CY predictive formulas as part of the laboratory cheese-making procedure (within-animal validation, WAV), in which the first %CY observation within animal was assigned to CAL, and the second to the VAL set. Finally, a stratified CrV (SCrV) was adopted to assess the %CY traits prediction accuracy across goat breeds, again using the best model, in which 5 breeds were included in CAL and the remaining one in the VAL set. Fitting statistics of the formulas were assessed by coefficient of determination of validation (R²_VAL) and the root mean square error of validation (RMSE_VAL). In CrV, the formula with the best prediction accuracy for all %CY traits included fat, casein, and UHI (R²_VAL = 0.65, 0.96, and 0.23 for %CY_CURD, %CY_SOLIDS, and %CY_WATER, respectively). The WAV procedure showed R²_VAL higher than those obtained in CrV, evidencing a low effect of the 9-MilCA method and, indirectly, its high repeatability. In the SCrV, large differences for %CY_CURD and %CY_WATER among breeds evidenced that the breed is a fundamental factor to consider in %CY predictive formulas. These results may be useful to monitor milk composition and quantify the influence of milk traits in the composite selection indices of specific breeds, and for the direct genetic improvement of cheese production.     

Thermal and photon effects on the reaction of H2 and O2 to water over Ag–Pd/TiO2

The reaction of H₂ and O₂ to water are studied over a Ag–Pd/TiO₂ anatase catalyst, under dark and photo-irradiation conditions in the gas and liquid phases. The catalyst consisted of metal particles of mean size of ca.1 nm dispersed over 10–15 nm TiO₂ particles. Kinetic parameters including order of reaction (n), rate constant (k), and activation energy (E_a), were evaluated. E_a for the thermal reaction was found to be 49-47 kJ mol^?1. The oxidation reaction rate constant was found to be ca. 3 times higher in the presence of photons when compared to dark reaction at room temperature. The overall quantum yield of the reaction in the slurry phase was found to be 0.09. Considering the number of metal particles on TiO₂, the photon yield per metal particle was found to be 0.16. A possible explanation of the changes in kinetics with respect to experimental conditions is given.     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

日本の寒地，北海道における2030年代の水稲生育への温暖化の影響予測とその対応(日语原文)

北海道では1980年代から2010年代まで，水稲圃場栽培期間である5–9月の気温は年代とともに上昇した。そこで，直近の2010年代（2010—2019年平均）と比べて， 2つの2030年代の予測気象から，既報の関係式より水稲生育を予測した。その結果，2030年代では2010年代に比べ，限界移植日（移植早限）が水稲栽培17地域の平均で8～9日早い。また，早限出穂期が1～5日早く，晩限出穂期が1～5日遅く，安全出穂期間が2～10日長い。出穂期は1～3日早い。出穂期から晩限出穂まで2～9日長いため，遅延型冷害の発生がやや少ない。生育期別気象は，出穂前24日以降30日間では生育が早いため平均気温が同じかやや低い。出穂前10日以降40日間および出穂期以降40日間では平均気温がやや高く，日射量はやや少ない。そのため，玄米収量は96～98％とやや低く，潜在収量性を示す気候登熟量示数は同じである。障害不稔発生に関係する穂ばらみ期冷害危険期の平均気温はわずかに低いかほぼ同じであるため，冷害発生の危険性は残る。一方，不稔発生をもたらす低温域の出現頻度には，地域間で差異がある。精米蛋白質含有率は同じであるが，アミロース含有率はやや低く，やや良食味である。米粒外観品質では被害粒歩合と着色粒歩合は一定の傾向がなく，未熟粒歩合はやや高い。精米白度は同じであるが，玄米白度はやや高い。以上の予測に対する技術的対応方向を示した。     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

Omega-6支撑身体，Omega-3支撑大脑：均衡摄入对儿童大脑发育的影响（网络首发、推荐阅读）

人体大脑和身体的发育，需要从食物中摄取均衡的营养物质。人类大脑是区分人类和其他动物的特征。食物中的必需脂肪酸是机体组织结构和功能的必要组成部分。Omega-6（O6）亚油酸（LA6）是皮肤组织的组成成分，且是炎症、血栓形成、免疫和其他信号分子的前体；Omega-3（O3）α-亚麻酸（ALA3），特别是其长链代谢产物——二十二碳六烯酸（DHA3），是大脑、视网膜和部分神经组织中的关键组分。从富含LA6脂肪酸（缺乏O3脂肪酸）的植物籽中提取出的廉价而优质油脂，是20世纪的西方国家食品工业生产的主要脂肪来源。在代谢通路中，高浓度的LA6脂肪酸可拮抗O3脂肪酸代谢，造成O3脂肪酸不足，因此，在给怀孕动物的饲料中，只提供富含LA6但缺乏O3脂肪酸的油脂作为唯一的脂肪来源，会导致幼崽大脑发育不良。过去20~30年的研究表明，低含量LA6且含DHA3的油脂可改善大脑的功能。近年来的研究较多集中在营养因素对大脑发育的影响，最新研究数据表明，脂肪酸平衡对营养不良儿童的大脑发育尤为重要。世界卫生组织（WHO）越来越重视大脑的营养健康，通过其下属的食品法典委员会，建议用于治疗严重急性营养不良儿童的即食治疗食品中，使用含有均衡脂肪酸组成/构成的脂肪。同样，脂肪酸均衡对老年人可能也很重要。目前，业界已经有了调整油脂成分的方法，以确保脂肪酸均衡，从而维持人体整个生命周期的大脑健康。     

Experimental study and numerical modeling of mixing by air injection in yield stress fluids using the OpenFOAM software

Mixing by gas injection is an operation used in industrial processes such as wastewater treatment, metallurgy, or methanization in which pressurized gas is injected into a fluid in order to reduce concentrations and temperatures gradients. This study demonstrates how the CFD toolbox OpenFOAM can be used to simulate such flows. Experimental measurements and observations have been performed on a pilot-scale reactor where pressurized air is injected in a yield stress fluid. The volume of fluid method and an adaptive mesh with refinement at the interface have been used to track the gas inclusions. The numerical model accuracy has been assessed by comparing experimental and numerical results related to the bubble's frequency, dimensions, and rising velocities as well as the fluid recirculation, yielded, and unyielded regions in the tank. The influence of injection parameters such as the injection flow rate and the fluid rheological parameters has been quantified.     

超高效液相色谱⁃四极杆⁃飞行时间质谱对含PET食品接触材料中可迁移非挥发性物质的筛查研究

采用超高效液相色谱⁃四极杆⁃飞行时间高分辨质谱（UPLC⁃Q⁃TOF）对4类不同类型的含聚对苯二甲酸乙二醇酯（PET）材质的食品接触材料在4 %乙酸和50 %乙醇模拟物中的迁移出的非挥发性未知物进行筛查解析。结果表明，产品在4 %乙酸模拟物的迁移风险远小于50 %乙醇模拟物，主要迁移物质为聚合单体形成的寡聚物，抗氧剂、润滑剂、胶黏剂等加工助剂以及生产加工、迁移过程中形成的非有意添加物（NIAS）物质；纯PET材质的产品迁移物质较少，多层复合材料迁移物质较多。复合材质的产品中，PET材质可能在生产时添加了己二酸、癸二酸、新戊二醇等物质，进行了改性处理；此外，部分迁移物质会与模拟物中的乙醇发生反应，生成新的NIAS物质。