离子型稀土矿山淋洗及尾水富集试验研究

对浸矿后离子型稀土原地浸矿场采用清水进行淋洗，在184天的清水淋洗过程中，尾水氨氮值从最开始的507mg/L，降低至140mg/L，淋洗尾水pH4.52~3.10。淋洗尾水采用两级反渗透膜分离，既回收有价资源稀土，又能使出水氨氮达标。结果表明，产水氨氮浓度稳定低于15mg/L，对稀土的截留率高于98.25%，浓水中稀土离子平均浓度313.4mg/L，可进一步回收稀土资源。     

High-entropy titanate pyrochlore as newly low-thermal conductivity ceramics

Low-thermal conductivity ceramics play an indispensable role in maximizing the efficiency and durability of hot end components. Pyrochlore, particularly zirconate pyrochlore, is currently a highly promising and widely studied candidate for its extremely low thermal conductivity. However, there are still few pyrochlores that offer both stiffness, insulation, and good thermal expansion properties. In this work, the solidification method was innovatively introduced into the preparation of titanate pyrochlore, and combined it with the compositional design of high-entropy. Through careful composition design and solidification control, the high-density and uniform elements distributed high-entropy titanate pyrochlore ceramics were successfully prepared. These samples possess high hardness (15.88 GPa) and Young’s modulus (295.5 GPa), low thermal conductivity (0.947 W·m^?1·K^?1), excellent thermal expansion coefficient (11.6 ×10^?6/K) and an exquisite balance between stiffness and insulation (E/κ, 312.1 GPa·W^?1·m·K), in which the E/κ exhibits the highest value among the current reported works.     

Structural,electrical, and linear/nonlinear optical characteristics of thermally evaporated molybdenum oxide thin films

Homogeneous thin films of Molybdenum oxide (MoO₃) were grown on quartz and glass substrates using the thermal evaporation method. XRD results showed that the MoO₃ powder has a polycrystalline structure with an orthorhombic crystal system whereas the MoO₃ thin films have amorphous nature. SEM images showed that the MoO₃ thin films have a nearly uniform surfaces with worm-like shape grains. The film thickness influences on the linear and nonlinear optical characteristics of MoO₃ thin films that were examined using spectrophotometric measurements and from which, the linear optical constants of the MoO₃ thin films were estimated. The electronic transition type was determined as a direct allowed one. The values of the optical band gap were obtained to be in the range of 3.88–3.72 eV. The dispersion parameters, third-order nonlinear optical susceptibility, and the nonlinear refractive index of the MoO₃ thin films were determined and interpreted in the light of the single oscillator model. The temperature dependence of the DC electrical conductivity and the corresponding conduction mechanism for the MoO₃ films were investigated at temperatures ranging from 303 to 463 K.     

Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

Novel proton-conducting layered perovskite based on BaLaInO4 with two different cations in B-sublattice: Synthesis,hydration, ionic (O2−, H+) conductivity

The present study focused on the novel material with significantly improved properties for the application in the area of clean energy. The new complex oxide BaLaIn_0·5Y_0·5O₄ with layered perovskite structure was obtained for the first time. It was proved that the introduction of Y³⁺ ions in the perovskite layer of BaLaInO₄ leads i) to the rise of the oxygen-ionic conductivity due to the increase in mobility of oxygen ions as a result of the expand of the cell volume and ii) to the enhancement of protonic conductivity due to the increase in the proton concentration and mobility. The sample BaLaIn_0·5Y_0·5O₄ is nearly pure proton conductor below 400 °C and has the protonic conductivity value 1.6?10^?5 S/cm at this temperature.     

Preparation of high-purity SiC ceramics with good plasma corrosion resistance by hot-pressing sintering

High-purity SiC ceramic devices are applied in semiconductor industry owing to their outstanding properties. Nevertheless, it is difficult to densify SiC ceramics without any sintering additive even by HP sintering. In this work, high-purity and dense SiC ceramics were fabricated by HP sintering with very low amounts of sintering aids. Residual B content was only 556 ppm and relative density was more than 99.5%. Furthermore, thermal conductivity of as-prepared SiC ceramics was improved from 155 W m^?1 K^?1 to 167 W m^?1 K^?1 by increasing holding time and their plasma corrosion resistance was promoted in the meantime. The as-prepared high-purity SiC ceramics have broad application prospects in the field of semiconductor industry.     

W波段用BeO-TiO2衰减瓷研究

以氧化铍、二氧化钛为原料,通过还原气氛烧结制备出BeO-TiO₂衰减瓷,采用扫描电镜、矢量网络分析仪及闪射法导热仪等检测仪器,研究了BeO-TiO₂衰减瓷的微观形貌及在W波段(75~110GHz)的微波衰减性能和导热性能。     

Laser damage resistance of plasma-sprayed alumina and honeycomb skeleton/alumina composite ceramic coatings

Al₂O₃ and honeycomb skeleton-Al₂O₃ composite coatings on Titanium alloy (Ti–6Al–4V) were prepared by atmospheric plasma spraying. A laser ablation experiment on as-sprayed coatings was performed. In this paper, the laser damage resistance, microstructure, phase composition of Al₂O₃ coatings were examined. 3D Dimensional Confocal Microscopy, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and Energy Dispersive Spectrometry (EDS) characterized the laser damage morphology, microstructure, phase composition, and element analysis, respectively. The influence of the honeycomb skeleton on the laser ablation damage on as-sprayed coatings was investigated by a comparative analysis of the laser damage morphology with different laser ablation times and gas flow. The results show that the honeycomb skeleton raises thermal conductivity and thermal diffusivity. Moreover, a “tower”-like dendrite was generated during the laser irradiation of the composite coating. The honeycomb skeleton refined the structure, suppressed crack propagation, and reduced the influence of gas flow on cracks. Under the same experimental laser ablation parameters, the laser damage area of the honeycomb skeleton-Al₂O₃ composite coating was smaller than that of the Al₂O₃ coating. It was demonstrated that the laser damage resistance of the honeycomb skeleton-Al₂O₃ composite coating was superior to that of the Al₂O₃ coating.     

Effect of nickel addition on the physicochemical properties of SrTiO3-based materials

Synthesis of materials in Ni/SrTiO₃ system was undertaken. Perovskite structure material with nominal composition SrTi_0.98O₃ was synthesised by the sol-gel method. Nickel was introduced into the system by the wet impregnation method followed by proper thermal treatment. Two research paths were carried out: the evaluation of sintering conditions on material properties (sintering temperature: 1100, 1200, 1300 and 1400 °C; sintering time: 1, 3 and 5 h for sintering at 1300 °C) and the effect of nickel addition on the material properties - 1, 2, and 5 mol% of Ni compared to the amount of Ti was introduced into the analysed system. The microstructures of the materials, together with their structural (XRD analysis) and electrical (total conductivity and Seebeck coefficient) properties, were determined. Furthermore, temperature-programmed reduction (TPR) and temperature-programmed oxidation (TPOx) measurements were performed to evaluate the materials’ redox properties. It was shown that less than 1 mol% of Ni could be incorporated into the strontium titanate structure when a wet impregnation was chosen as the method for the introduction of Ni into the SrTiO₃-based system. NiO and, for the highest amount of introduced nickel, also NiTiO₃ were the main additional nickel-containing phases. For all materials synthesised in the Ni/SrTiO₃ system, the positive value of the Seebeck coefficient was observed, suggesting that nickel is an acceptor-type dopant while incorporated into the perovskite structure. However, the TPR measurements clearly imply that nickel can be incorporated into the strontium titanate structure in various oxidation states.