聚丙烯酸酯/醇酸树脂复合乳液的合成与表征

用乳液聚合法合成了聚丙烯酸酯/醇酸树脂复合乳液,研究了醇酸树脂组成和用量及聚合条件对动力学和复合乳液性能的影响。结果表明,醇酸树脂对乳液聚合有明显的阻聚作用,而且这种阻聚作用随醇酸树脂中马来酸酐含量的增加而加剧。升高聚合温度和增加引发剂用量均有利于改善乳液的机械稳定性。随着醇酸树脂用量的增加,复合乳液的机械稳定性和涂膜的耐水性逐渐提高;醇酸树脂中马来酸酐含量增加,乳液机械稳定性提高,当醇酸树脂中马来酸酐质量分数为2 4%时,涂膜具有最佳的耐水性。     

以表面负载季铵盐阳离子型苯/丙乳胶粒为模板制备ZrO_2空心微球

以C9油与甲基丙烯酰氧乙基三甲基氯化胺的共聚物P(C9-DMC)为乳化剂制备苯/丙阳离子乳胶粒,并以其为模板,利用直接包覆法制备了由17 nm左右微晶体堆成的ZrO2空心微球。所制得的样品采用FT-IR、XRD、TEM和SEM等进行了表征。     

用SBR1502胶浆制取道路沥青改性用胶乳

用附聚法和降粘法浓缩ＳＢＲ１５０２胶浆制取道路沥青改性用胶乳。结果表明：总固物质量分数可由（２１±２）％上升到４５％～５０％。该胶乳与齐鲁石化公司炼油厂１００号乙沥青混合，改性后的道路沥青具有良好的使用性能，可满足高等级路面沥青的技术要求。     

高透明耐冲击聚氯乙烯接枝聚合研究

研究高透明耐冲击聚氯乙烯接枝聚合工艺，讨论了加料顺序、复合分散体系以及采用聚集粒子乳液、并用碱性物质调节其ｐＨ值等对接枝聚合物性能的影响，确定了接枝聚合最佳工艺条件。     

丁苯胶乳改性道路沥青的推广应用

用丁苯胶乳对胜利１００号沥青进行改性试验．发现随着胶乳掺量的增加．沥青的高温性能、粘结性能改善幅度也大。但综合考虑沥青生产成本等因素．认为：对丁苯胶乳改性胜利１００号道路沥青．掺胶量控制在２％即可满足一般高等级道路工程的需要。文中还介绍了丁苯胶乳沥青近年来的推广使用情况并做了相应的技术经济分析和建议。     

零VOC乳胶涂料的研究进展

在分析乳胶涂料中VOC主要来源的基础上,从乳液合成和助剂选择两方面阐述了消除VOC的途径.详细探讨了利用核壳乳液聚合、引入功能性单体和软硬乳液混拼等思路来解决乳液的高玻璃化温度(Tg)和最低成膜温度(MFT)之间的矛盾,并简单介绍了零VOC乳胶涂料中极低VOC含量的检测方法和标准.     

Effects of mastication on the distribution of molecular weights and on the mechanical properties of native and commercial dental gutta percha (trans-polyisoprene)

Mastication of gutta percha (trans-polyisoprene) resulted in the selective scission of molecules, producing a narrower distribution of lower molecular weights. The mechanical properties of the samples also underwent a significant change due to mastication. The greater the content of incompatible substances (salts and oxides) in commercial gutta percha. the more substantial were these effects. The atmosphere (air, N₂, O₂) in which the experiments were conducted yielded significantly different results. The decrease in molecular weight was far greater in an O₂ atmosphere than under a current of nitrogen or air, owing to the combination of double bonds with O₂.     

乳胶漆的市场现状和发展前景

对乳胶漆的生产现状，产品结构以及研究开发情况作了简单的综述，并展望了乳胶漆的发展前景。     

A comparative study of short nylon fiber—Natural rubber composites prepared from dry rubber and latex masterbatch

A novel method for the preparation of short nylon fiber–natural rubber composites was developed in which short fibers chopped to approximately 6 mm were incorporated in the latex stage and processed into sheet form. By this method, mixing cycle time was reduced without compromising the fiber dispersion. Fiber breakage during mixing was reduced. The new composites when compounded with a dry bonding system based on hexamethylenetetramine, resorcinol and hydrated silica (HRH) showed improved modulus, tensile strength and abrasion resistance compared to conventional composites. Tear strength, resilience, and compression set were similar to the conventional composites. SEM analysis indicated better interaction between matrix and fibers in the case of latex master batch. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008