井下液气分离器分离原理及结构改进

液气分离器就是充分利用电泵机组的高转速、气体和液体之间悬殊的密度差异进行液气离心分离。经过多年的发展,在传统的液气分离器结构基础上又出现了许多新的设计和改进,大大提高了液气分离器的分离效果。文章重点论述了液气分离器的分离原理和结构上的改进之处。     

Modeling and simulation of a fully air swept ball mill in a raw material grinding circuit

A raw material grinding circuit was modeled using plant data. Samples were collected from around the circuit and, following a crash stop, from inside the mill. The size distributions of the samples were determined down to a few microns. Using the data from inside the mill a modeling approach, based on perfect mixing, was developed. The modelling approach implicitly assumes that the mixture of feed materials broken is homogenous from the breakage point of view. The air classification around the circuit was modeled using the efficiency curve approach. In order to measure the success of the method the circuit performance was predicted by simulation studies while it was operating at different conditions. The results were then compared with the measured data. It is concluded that modeling gives a useful quantitative indication of what may occur in fully air swept mills.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

导磁不锈钢毛的结构化研究

研制了一种新型的结构化钢毛——胶结钢毛。和传统的普通钢毛相比,胶结钢毛具有很强的结构刚度和很低的钢毛流失量;同时,对高岭土有较高的除铁效率。     

乙苯/苯乙烯塔分离效率问题的技术分析及整改措施

分析了齐鲁分公司200kt/a乙苯/苯乙烯装置乙苯/苯乙烯塔(T-401)分离效率低的原因,即降液管设计偏小,液体在降液管内流速过快,引起液体飞溅;安装分布器使用的石棉垫片溶胀而粉碎后堵塞了分布槽;分布器上使用的垫片脱落形成缝隙而漏液;填料装得不密实,留有缝隙;二级分布槽变形等.针对存在问题提出了相应的整改措施,并考察了整改措施实施效果.结果表明,整改后该塔的分离能力满足了工艺要求,并有一定的操作弹性.     

排气管偏置对PV型旋风分离器性能影响的研究

以Ф300mm、标准PV型旋风分离器为基准模型进行冷态对比实验，研究了排气管与筒体轴线偏心布置对PV型旋风分离器分离性能的影响。结果表明，排气管偏置是进一步提高PV型旋风分离器性能的有效措施之一。在适当的偏心矩和偏置方位下，不仅能降低压降，还可以显著提高分离效率。     

NUMERICAL SIMULATION OF PARTICLE SEPARATION IN AN OIL-SAND SEPARATOR

ＮＯＴＡＴＩＯＮＳＡ　Ａｒｅａｏｆｉｎｌｅｔ ,ｍ2ａ　Ｃｅｎｔｒｉｆｕｇａｌａｃｃｅｌｅｒａｔｉｏｎ ,ｍ2 /ｓｉ　Ｇｒｉｄｏｆａｘｉａｌｄｉｒｅｃｔｉｏｎｍｌ 　ＭａｘｉｍｕｍｇｒｉｄｎｕｍｂｅｒｏｆｒａｄｉａｌｄｉｒｅｃｔｉｏｎＱ　Ｆｌｕｉｄｍａｓｓｒａｔｅ ,ｍ3/ｓＲｃ 　Ｍａｘｉｍｕｍｒａｄｉｕｓｏｆｃｙｃｌｏｎｅ ,ｍＲｅ　Ｒｅｙｎｏｌｄｓｎｕｍｂｅｒｒ　Ｄｉｍｅｎｓｉｏｎｌｅｓｓｒａｄｉａｌｄｉｓｔａｎｃｅｔ　Ｄｉｍｅｎｓｉｏｎｌｅｓｓｔｉｍｅｕ　Ｄｉｍｅｎｓｉｏｎｌｅｓｓａｘｉａｌｖｅｌｏｃ…     

Direct-Ink-Writing of Electroactive Polymers for Sensing and Energy Storage Applications

Considering the high levels of materials used in the fields of electronics and energy storage systems, it is increasingly necessary to take into consideration environmental impact. Thus, it is important to develop devices based on environmentally friendlier materials and/or processes, such as additive manufacturing techniques. In this work, poly(vinylidene fluoride) (PVDF) and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) are prepared by direct-ink-writing (DIW) by varying solvent evaporation temperature and fill density percentage. Different morphologies for both polymers are obtained, including dense films and porous membranes, as well as different electroactive β-phase content, thermal and mechanical properties. The dielectric constant and piezoelectric d₃₃ coefficient for dense films reaches up to 16 at 1 kHz and 4 pC N⁻¹, respectively for PVDF-HFP with a fill density of 80 and a solvent evaporation temperature of 50 °C. Porous structures are developed for battery separator membranes in lithium-ion batteries, with a highest ionic conductivity value of 3.8 mS cm⁻¹ for the PVDF-HFP sample prepared with a fill density of 100 and a solvent evaporation temperature of 25 °C, the sample showing an excellent cycling performance. It is demonstrated that electroactive films and membranes can be prepared by direct-ink writing suitable for sensors/actuators and energy storage systems.     

蒸发二段真空度不稳定原因分析

对斯那姆尿素工艺二段蒸发真空度不稳定原因进行了较详细的分析，并提出相应的操作处理措施     

中压分离器夹套部位接管组焊工艺

针对中压分离器夹套部位接管结构特点,分析了在制造过程中所面临的困难问题。介绍了为此而制定的特殊工艺方案以及方案的实施情况和结果。