Densification effects on the fracture in fused silica under Vickers indentation

This study investigates the effects of densification on the deformation and fracture in fused silica under Vickers indentation by both the finite element analysis (FEA) and experimental tests. A refined elliptical constitutive model was used, which enables us to investigate the effects of the evolution of yield stress under pure shear and elastic properties with densification. The densification distribution was predicted and compared with experiments. The plastic deformation and indentation stress fields were used to analyze the initiation and morphology of various crack types. The formation mechanism of borderline cracks was revealed for the first time. This study reveals that the asymmetry of the densification distribution and elastic-plastic boundary significantly influences the cracking behavior. Under the Vickers indentation, conical cracks have the largest penetration depth. When these cracks emerge from a region far from the impression, they extend with constant radii to form circles on the sample surface. Otherwise, they tend to be initiated at the centers of the indenter-material contact edges before propagating towards the impression corners with increasing radii. Therefore, the borderline cracks consisting of successive partial conical cracks can form at a low load and makes them the first type of crack to appear.     

Charge source and the charging mechanism of the contact electrification of polymer powder

The charge sources, as well as the charging mechanism of the contact electrification (CE) of polymers, are still debatable. Since CE is accompanied by destruction, it is considered that “hard contacting” via ball milling can induce covalent bond scission and produce naked-activated-charge sources. Regarding “soft contacting” via nano-scale sliding, which does not induce covalent bond scission, a frontier-electron, “f-electron,” of the naked-activated-charge source is crucial to electron transfer among the naked-activated-charge sources. Here, we configure naked-activated-charge-source models, naked-activated-mechano-anion, and naked-activated-mechano-cation, which are produced by mechanical energy induced heterogeneous covalent bond scission, as well as naked-activated-mechano-radicals that are produced by homogeneous covalent bond scission. Regarding “soft contacting” among naked-activated-charge sources in a vacuum, f-electron can be transferred from a donor to an acceptor if the energy level of the donor is higher than that of the acceptor. The net amount of the normalized transferred-f-electrons is obtained by adopting settings in which the average energy level of the naked-activated-charge sources (as the donors) is higher than that of the sources employed as acceptors. Thus, the surfaces comprising the donors and acceptors will exhibit positive and negative net surface charges, respectively. We conclude that net surface charges depend on the average energy level of naked-activated-charge sources. Further, we observe that the alignment of polyethylene (PE)-polyvinyl chloride (PVC)-polytetrafluoroethylene (PTFE) to the average energy level is identical to that of the triboelectric series.     

负载羧基化球状介孔纳米颗粒TFN膜的研究

在薄层复合膜(thin-film composite membrane, TFC膜)中引入无机纳米颗粒，形成薄层纳米复合膜(thin-film nanocomposite membrane, TFN膜)，近几年作为反渗透膜开始应用于水处理研究。但是无机纳米颗粒在TFC膜中的性能的不稳定性和膜的机械强度等变成了突出问题。合成制备了粒径约为110 nm修饰羧基的介孔氧化硅球状纳米颗粒(MSN—COOH)，并将其成功地化学键合在TFC膜的表面功能层交联网络中。与TFC膜相比，键合有MSN—COOH的TFN膜，水通量提高了56.2%，保持高脱盐率；由于单分散介孔纳米颗粒表面亲水官能团的引入，使膜表面的亲水性有很大程度提高，单分散介孔纳米颗粒在基体中的有序排列，使膜表面粗糙度降低，提高了膜的抗污染能力。与普通TFN膜相比较，具有更好的稳定性和柔韧性，可以在长时间高压过滤操作下保持稳定。     

基于声源定位的高校在线巡课系统设计与研究

随着网络建设以及信息化教学方法在高校教学过程中的应用普及,越来越多的高校使用在线巡课系统对教师的教学过程进行跟踪和管理,以便发现课堂教学中的亮点、问题和不足。文章提出的在线巡课系统,基于声源定位的技术,对传统的在线巡课系统做出了改进,解决了已有巡课系统中“只闻其声,不见其人”的问题,能够更直观地跟踪到教师的教学过程,包括教学行为以及师生互动过程,有效提升教务人员巡课效果和体验感受。     

压水堆核电厂堆外源量程探测器计数率分析

压水堆核电厂启动过程中，次级中子源为堆外源量程探测器提供本底计数率，避免测量盲区，确保反应堆安全启动。但次级中子源的引入会为核电厂带来较大的经济和环境负担，同时也需承受次级中子源破损等带来的风险。为此，可使用受辐照燃料组件的自发裂变中子源进行替代，即无源启动方式。通过研究堆外源量程探测器计数率的理论计算方法，并基于运行电厂测量数据进行分析验证，为源量程探测器计数率的理论预估提供了较为完善的理论方法流程。本文结果可为无源启动源量程探测器计数率分析提供支持，同时也可用于次级中子源装载量或布置位置的优化分析等。     

Inverse identification of constitutive parameters from heat source fields: A local approach applied to hyperelasticity

In this paper, a new inverse identification method of constitutive parameters is developed from full kinematic and thermal field measurements. It consists in reconstructing the heat source field from two different approaches by using the heat diffusion equation. The first one requires the temperature field measurement and the value of the thermophysical parameters. The second one is based on the kinematic field measurement and the choice of a thermo-hyperelastic model that contains the parameters to be identified. The identification is carried out at the local scale, ie, at any point of the heat source field, without using the boundary conditions. In the present work, the method is applied to the challenging case of hyperelasticity from a heterogeneous test. Due to large deformations undergone by the rubber specimen tested, a motion compensation technique is developed to plot the kinematic and the thermal fields at the same points before reconstructing the heterogeneous heat source field. In the present case, the constitutive parameter of the Neo-Hookean model has been identified, and its distribution has been characterized with respect to the strain state at the surface of a cross-shaped specimen.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

NH2-MCM-41的改性及其pH响应性释药的研究

采用正硅酸乙酯（TEOS）和3-氨丙基三乙氧基硅烷（APTES）通过共缩聚法合成介孔二氧化硅（MCM-41）。首先对其氨基修饰，再通过有机合成接枝—R基团（—R：—CHO、—OH、—CH₃、—COOH），制备得到Me-Ph-NH-MCM-41、OHC-Ph-NH-MCM-41、HO-Ph-NH-MCM-41、HOOC-Ph-NH-MCM-41四种不同的药物载体。利用FT-IR、Zeta电位、XRD和SEM对其结构和形貌表征，结果表明NH₂-MCM-41改性成功。以罗丹明B（RhB）为模型进行载药性能测试，并考察了此释药系统在模拟不同pH的体液下的敏感释药行为，同时探究了不同—R基团对释药的影响。结果显示，四种载体在中性条件下几乎不发生药物释放，通过改变环境体系pH可以有效控制药物释放，其释药行为可以用Korsmeyer-Peppas动力学模型来描述。实验表明，释药量：RhB@HOOC-Ph-NH-MCM-41>RhB@OHC-Ph-NH-MCM-41>RhB@HO-Ph-NH-MCM-41>RhB@Me-Ph-NH-MCM-41，不同—R基团的药物载体的pH响应性不同，其中RhB@HOOC-Ph-NH-MCM-41释药量在pH=1.2时可达57.87%，在用于药物智能控释材料方面具有一定的应用潜力。     

Modelling of electron energy absorption and backscattering during EBW

A three-dimensional heat flux model for deep-penetrating electron beam welding (EBW) is established to mathematically describe the physical heat generation process during interaction between electrons and the dynamic molten pool free surface. Monte Carlo method is used to determine the electron-target interaction, and random distribution of initial electrons, progressive trajectory tracing and electron backscattering models are used to describe the spatial distribution of electrons absorption. The model is verified in preset keyholes and applied in the simulation on electron beam welding process, and the calculated bead shape shows a good consistency with experimental results.