Optical properties and conductivity of PEDOT:PSS films treated by polyethylenimine solution for organic solar cells

We report on conductivity and optical property of three different types of poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) films [pristine PH1000 film (PH1000-p), with 5 wt.% ethylene glycol additive (PH1000-EG) and with sulfuric acid post-treatment (PH1000-SA)] before and after polyethylenimine (PEI) treatment. The PEI is found to decrease the conductivity of all the PEDOT:PSS films. The processing solvent of 2-methoxyethanol is found to significantly enhance the conductivity of PH1000-p from 1.1 up to 744 S/cm while the processing solvent of isopropanol or water does not change the conductivity of PH1000-p much. As for the optical properties, the PEI treatment slightly changes the transmittance and reflectance of PH1000-p and PH1000-EG films, while the PEI leads to an substantial increase of the absorptance in the spectral region of 400–1100 nm of the PH1000-SA films. Though the optical property and conductivity of the three different types of PEDOT:PSS films vary with the PEI treatment, the treated PEDOT:PSS films exhibit similar low work function. We demonstrate solar cells with a simple device structure of glass/low-WF PEDOT:PSS/P3HT:ICBA/high-WF PEDOT:PSS cells that exhibit good performance with open-circuit voltage of 0.82 V and fill factor up to 0.62 under 100 mW/cm² white light illumination.     

Influence of Bridgman solidification on microstructures and magnetic behaviors of a non-equiatomic FeCoNiAlSi high-entropy alloy

The non-equiatomic FeCoNiAlSi alloy is prepared by the Bridgman solidification (BS) technique at different withdrawal velocities (V = 30, 100, and 200 μm/s). Various characterization techniques have been used to study the microstructure and crystal orientation. The morphological evolutions accompanying the crystal growth of the alloy prepared at different withdrawal velocities are nearly the same, from equiaxed grains to columnar crystals. The transition of coercivity is closely related to the local microstructure, while the saturation magnetization changes little at different sites. The coercivity can be significantly reduced from the equiaxed grain area to the columnar crystal area when the applied magnetic field direction is parallel to the crystal growth direction, no matter what is the withdrawal velocity. In addition, the alloy possesses magnetic anisotropy when the applied magnetic field is in different directions.     

Impact sensitivities of energetic materials: Exploring the limitations of a model based only on structural formulas

Using a comprehensive set of drop weight impact test data (h₅₀) newly compiled from literature for 308 materials, a recent approach to predict impact sensitivities of nitro compounds is generalized to most explosive substances of interest. Compared to previous ones, this procedure is more thoroughly validated and exhibits a good predictive value. Furthermore, it yields new insight into the physical mechanisms involved, explaining for instance the unexpected desensitization of some oxygen-deficient triazoles upon nitration.     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Suitability,efficiency and microbiological safety of novel physical technologies for the processing of ready‐to‐eat meals,meats and pumpable products

Consumer studies and market reports show an increase in consumption of ready‐to‐eat (RTE) foods. Although conventional processing technologies can in most cases produce safe products, they can also lead to the degradation of nutritional compounds and negatively affect quality characteristics. Consumers strongly prefer food that is minimally processed with the maximum amount of health‐promoting substances. Novel processing technologies as pre‐ or post‐treatment decontamination methods or as substitutes of conventional technologies have the potential to produce foods that are safe, rich in nutrient content and with superior organoleptic properties. Combining novel with conventional processes can eliminate potential drawbacks of novel technologies. This review examines available scientific information and critically evaluates the suitability and efficiency of various novel thermal and nonthermal technologies in terms of microbial safety, quality as well as nutrient content on the production of RTE meals, meats and pumpable products.     

埋地管道在冻土带的热力变形分析

埋地油气管道通过永冻土地带时,由于管内介质与周围的冻土发生了热力作用,使冰土解冻,在管道周围形成融化圈。文章分析了永冻土的特点,建立了永冻土地带土壤传热数学模型:融化圈内外传热方程、管道向土壤和土壤表面向大气所放热量的守恒关系、融化圈界面处土壤温度、相变界面处固相变为液相的传热条件。还建立了埋地管道模型,并以穿过永冻土地带土壤的输油管道为例,分析并计算了各种应力的最大值所在的位置和大小,提出了在永冻土地带减小管道热力变形的措施。     

ca油田稠油油藏系统保护油气层研究

针对ca油田多层状砂泥薄互层稠油油藏的特点,开展了热采和非热采条件下储层变化特征研究、钻井和固井过程入井液的研究、采油工艺技术等系统保护油气层研究,了解各种变化的作用过程和原因,有效地预防现场施工中可能发生的储层伤害,从而达到储层保护、提高采收率的目的。     

储层应力敏感性影响因素研究

全面分析储层应力敏感性产生的机理认为，外部因素的改变会引起储层产生应力敏感性．而储层岩石物性等内部因素对应力敏感性的强弱起决定性作用。室内岩心应力敏感性评价时．仪器与设备的精度、加载与卸载方式、实验用流体类型以及各种人为因素等都会对评价结果产生影响，其中岩心密封套在高压、高温条件下的密闭性会对实验结果产生较大影响。所以储层应力敏感性不应该从孔隙度和渗透率的高低进行简单评价，中、高渗储层和低渗储层在生产过程也都可能表现出较强的应力敏感性现象。