T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

用测井资料预测储层的润湿性

岩心电性及润湿性实验测量结果表明，润湿性对阿尔奇饱和度指数n有很大影响。通过引入相对润湿指数，发现阿尔奇饱和度指数n的对数与相润湿指数之间存在很好的线性关系，为利用饱和度指数预测储层的润湿性提供了依据。同时使用电磁波传播测井和微球形聚焦电阻率测井求出饱和度指数随地层深度的变化曲线，预测储层的润湿性。现场井资料处理结果表明，该方法能快速直观显示不同深度处储层润湿性的变化。     

高温钎料PdCu-Ti在氧化铝陶瓷上的润湿性及界面反应

本文采用座滴法试验研究了合金系统ＰｄＣｕ－Ｔｉ在Ａｌ２Ｏ３上润湿性的变化规律，探讨了界面冶金及结合等行为，运用热力学理论对结果进行了分析，随Ｔｉ含量的增加及Ｐｄ含量的减少润湿角逐渐降低，Ｔｉ的加入使界面发生了一个双重变化；液相侧富氧，钛吸收层的生成及随后的固相侧氧化钛的生成，只有界面上生成一氧化钛，才能有较好的润湿行为和较强的结合力。     

Au-Ag-Si新型中温共晶钎料的研究

根据合金相图的基本原理,分析了Au-Ag-Si系相图,研制出熔化温度在400℃～500℃的共晶钎料合金.通过钎料合金与Ni板的润湿性测试和润湿后界面的微观组织分析.结果表明:Au-Ag-Si系钎料对于纯Ni具有良好的漫流性和润湿性,在450℃～500℃范围内,可以对Ni板进行钎焊.     

Sn-Cu系无铅钎料的研究现状与发展

介绍了无铅钎料应用时应该满足的基本要求和Sn-Cu系无铅钎料的国内外研究和应用现状,概述了Sn-Cu系无铅钎料润湿性能、物理性能、力学性能等方面的一些特点,分析探讨了Sn-Cu系无铅钎料存在的不足,详细阐述了添加不同合金元素(如Bi、Ag、Ni、RE等元素)对Sn-Cu系无铅钎料性能的影响规律,并对Sn-Cu系无铅钎料的应用前景和发展方向进行了展望.