Effect of nitriding atmosphere on the morphology of AlN nanofibers from solution blow spinning

High purity AlN fiber is a promising thermal conductive material. In this work, AlN fibers were prepared using solution blow spinning followed by nitridation under N₂ or NH₃ atmosphere. Soluble polymer, such as polyaluminoxane, and allyl-functional novolac resin were adopted as raw materials to form homogeneous distribution of Al₂O₃ and C nanoparticles within the fibers, which could inhibit the growth of alumina crystal and promote their nitridation process. The effect of nitriding atmosphere on the fiber morphology was investigated. XRD results showed that complete nitridation was achieved at 1300 °C in the NH₃ or at 1500 °C in the N₂ atmosphere. Hollowed fiber structure was observed when fiber was nitrided in N₂ at high temperature, which was caused by gaseous Al gas diffusion, and this phenomenon was eliminated in NH₃ atmosphere. The nitridation mechanisms in different atmosphere were analyzed in detail. It was demonstrated that the nitridation of Al₂O₃ fibers in the NH₃ atmosphere offered the favored AlN morphology and chemical quality. Flexible AlN fiber with O content of 0.7 wt% was achieved after nitriding in NH₃ at 1400 °C. The high quality AlN can be used in thermal conductive composite materials.     

高过滤性能石墨烯复合纳米纤维膜的制备及性能

将石墨烯(GR)纳米颗粒掺杂到聚丙烯腈(PAN)纺丝溶液中,利用静电纺丝技术制备石墨烯/聚丙烯腈(GR/PAN)复合纳米纤维膜。研究PAN质量分数、GR用量、纺丝电压及接收距离对GR/PAN复合纳米纤维膜形貌和过滤性能的影响,发现最优纺丝工艺参数为PAN质量分数14.0%、GR用量1.5%、纺丝电压26 kV、接收距离14 cm、注射速度1 mL/h。此最优纺丝工艺参数制备的GR/PAN复合纳米纤维膜的过滤效率为98.86%,过滤阻力为110.30 Pa。     

Electrochemical hydrogen storage performance of as-cast and as-spun RE-Mg-Ni-Co-Al-based alloys applied to Ni/MH battery

The La-Mg-Ni-Co-Al-based AB₂-type La_0.8–xCe_0.2Y_xMgNi_3.4Co_0.4Al_0.1 (x=0, 0.05, 0.1, 0.15, 0.2) alloys were prepared via melt spinning. The analyses of the X-ray diffraction (XRD) and scanning electron microscopy (SEM) proved that the experimental alloys contain the main phase LaMgNi₄ and the second phase LaNi₅. Increasing Y content and spinning rate lead to grain refinement and obvious change of the phase abundance without changing phase composition. Y substitution for La and melt spinning make the life-span of the alloys improved remarkably, which is attributed to the improvement of anti-oxidation, anti-pulverization and anti-corrosion abilities. In addition, the discharge capacity visibly decreases with increasing the Y content, while it firstly increases and then decreases with increasing spinning rate. The electrochemical kinetics increases to the optimum performance and then reduces with increasing spinning rate. Moreover, all the alloys achieve to the highest discharge capacities just at the initial cycle without activation.     

安泰贝抗菌黏胶大提花面料的开发

安泰贝抗菌黏胶纤维与精细棉混纺,在纺纱过程中需要对安泰贝抗菌黏胶纤维进行预处理,需合理调整流程及工艺参数;对织造过程中整经注意事项、浆料选择及织机参数的设定进行了说明;采用酶退浆后进行烧毛、冷轧堆前处理与染色,工艺参数与染化料用量控制在较低限度内;后整理选用亲水性柔软剂,可以赋予织物持久亲水性。通过工艺调整,成功开发了安泰贝抗菌黏胶大提花面料。     

镍基高温合金锥筒形件拉深旋压成形机理研究

针对镍基高温合金因加工硬化严重成形时极易产生破裂和起皱等典型缺陷的问题,以锥筒形壳体类零件为对象,提出了一种由锥形预制坯经过真空固溶处理后拉深旋压成形锥筒形件的方法,并对其成形机理进行了研究。基于Abaqus/Explicit平台,建立了锥筒形件拉深旋压有限元模型,分析了成形过程中的瞬态等效应力、等效塑性应变、切向应力、壁厚及三向应变分布规律。结果表明:在旋压成形过程中,最大瞬态等效应力位于旋轮接触区及附近区域、最大瞬态等效塑性应变位于坯料口部;瞬态切向压应力最大值位于旋轮接触区,而瞬态切向拉应力最大值位于旋轮接触区附近的两侧区域。筒形段中部壁厚减薄,而坯料口部壁厚增厚。旋压成形试验表明,锥形预制坯经拉深旋压后可获得壁厚均匀的锥筒形件。     

撞击流反应器撞击面稳定性研究进展

撞击流技术因其良好的混合特性近些年用于强化制备超细粉体反应中的混合过程。撞击面的稳定影响反应器内的混合效果，所以本文对撞击面稳定性的研究进行了综述。撞击流反应器不同结构形式包括平面撞击流、轴对称撞击流和微型撞击流等。文中简述了撞击流稳定性的实验研究手段，分析轴对称撞击流反应器的径向偏转振荡的起止条件和不同喷嘴间距下的轴向偏移振荡规律，并且分析平面撞击流反应器的撞击面偏转周期以及偏转振荡的起止条件。得出轴对称撞击流与平面撞击流撞击面驻点的振荡对混合都有促进作用，并且偏移振荡周期不定，轴对称撞击面偏移振幅与喷嘴间距和雷诺数相关。平面撞击流的偏转振荡周期与进口流速成反比，反应器结构参数是撞击流稳定性的影响因素之一。根据轴对称撞击流偏移振荡对混合的促进作用，本文提出一种新型的预设流量波形双组撞击流反应器。新型撞击流反应器的独特结构克服了物料反应通道单一缺点，通过预设波形控制其进口流量，增大其撞击面偏移振幅，消除撞击面无序振荡，使流动轨迹扩展，扩大混合区域，并设计实验装置与方法讨论动态流量撞击流反应器撞击面稳定性对混合效果的影响。最后，本文对轴对称撞击流反应器的混合性能研究前景进行展望。     

可调偏迈步式胶带自移机尾的研究

随着掘进工作面自动化程度的提高,掘进巷道速度也在日益加快,而现有的顺槽皮带机机尾移动缓慢且移动时工作量大,需要两三人配合操作,存在一定的安全隐患。针对以上问题,研发可调偏迈步式胶带自移机尾,具有与悬挂二运皮带转载机搭接行程长,可以迈步式前进,自动调偏等功能,同时,可以降低工人的劳动强度,加快巷道掘进速度。     

GO/PI复合纳米纤维的制备及其过滤性能研究

为制备高过滤效率、低过滤阻力的空气过滤材料,将氧化石墨烯纳米颗粒(GO)掺杂到聚酰亚胺(PI)纺丝溶液中,制备氧化石墨烯/聚酰亚胺(GO/PI)复合纳米纤维过滤材料。通过观察其形貌、过滤性能来确定最优纺丝工艺参数。结果表明:当PI质量分数为30%,GO质量分数为1%,纺丝电压为25 kV,接收距离为20 cm时,复合纳米薄膜的纤维形貌较好,过滤性能优良。与PI纯组分纳米纤维过滤材料相比,GO/PI复合纳米纤维过滤材料的过滤性能更好,制得GO/PI复合纳米纤维膜的平均孔径为1.8μm,过滤效率为99.68%,过滤阻力仅为85.35 Pa。     

Solution blow spun titania nanofibers from solutions of high inorganic/organic precursor ratio

In this work titania nanofibers were produced from different precursor solutions by solution blow spinning. Hydrophilic polyvinylpyrrolidone, hydrophobic poly(vinyl acetate) and amorphous and semi-crystalline poly(lactic acid) polymers were used with green-solvents and titanium isopropoxide as the inorganic precursor. Hybrid nanofibers with high inorganic loading content were successfully produced from all precursor solutions. The fibers were calcined at different annealing temperatures for evaluation of phase transitions. The minimum temperature to obtain pure titania fiber was found to be 500 °C, as assessed by thermal characterization. Anatase was the unique polymorph formed at this annealing temperature. This is of paramount importance due to its photocatalytic character. Calcination at high temperatures showed that rutile slightly appeared at 600 °C for the polyvinylpyrrolidone-based system and showed a strong peak at 700 °C for all systems, co-existing with anatase as minor phase. The use of amorphous and semicrystalline poly(lactic acid) polymers did not influence the anatase crystal size and phase conversion. This was found to be dependent on the annealing temperature and medium acidity, as currently found in powder synthesis.